• Journal of the Korean Wood Science and Technology
• /
• v.15 no.3
• /
• pp.44-55
• /
• 1987

In order to study the effect of sawdustboard combined with plastic chips, 0.5mm($T_1$), 1mm($T_2$), 1.4mm($T_3$) thick nylon fiber. polypropylene rope fiber(RP), and 0.23mm thick moth-proof polypropylene net fiber(NP) were cut into 0.5, 1, 2cm long plastic chips. Thereafter, sawdustboard combined with plastic chips prepared as the above and plastic non-combined sawdustboard(control) were manufactured into 3 types of one-, two-, and three layer with 5 or 10% combination level. By the discussions and results at this study, the significant conclusions of mechanical and physical properties were summarized as follows: 1. The MORs were shown in the order of 3 layer> 2 layer> 1 layer among plastic non-combined boards, and $T_3$ < $T_2$ < $T_1$ < RP (NP(5%) < NP(l0%) among plastic combined boards. In 2cm long plastic chip in 1 layer board, the highest strength through all the composition was recognized. 1 layer board showing the lower strength with 0.5cm plastic chip rendered to the bending strength improvement by 2 or 3 layer board composition. On the other hand, 2 or 3 layer combined with 1, 2cm long polypropylene net fiber chips incurred MOR's conspicuous decrease requiring optimum plastic chip combined level and consideration to combined type. 2. MOE in plastic non-combined 3 layer board exhibited sandwich construction effect by higher resin content application to surface layer in the order of 3layer>1layer>2layer with the highest stiffness of the board combined with polypropylene chip, while nylon chip-combined board had little difference from plastic non-combined board. In relevant to length and layer effect, 3 layer board combined with the 0.5cm long polypropylene net fiber chip in 5% and 10% combined level presented 34-43% and 44-76% stiffness increase against plastic non-combined board(control), respectively. Moreover, in 1 layer board, 30% stiffness increase with 10% against 5% combined level in the 1 and 2cm long polypropylene net fiber chip was obtained. 3. Stress at proportional limit(Spl) showing the fiber relationship (r: 0.81-0.97) between MOR presented in the order of 1 layer<2 layer<3 layer in plastic non-combined board. Correspondingly, combined effect by layer and plastic chip length was similar to MOR's. 4. Differently from previous properties(MOR, MOE, Spl). work to maximum load(Wml) of 2 layer board approached to that of 3 layer board. Conforming the above phenomenon. 2 layer combined with 0.5cm long polypropylene net fiber chip kept the greater work than 1 layer. The polypropylene combined board superior to nylon -and plastic non - combined board seemed to have greater anti - failing capacity. 5. Internal bond strength(IB), in contrast to MOR's tendency. showed in the order of T1

• Current Research on Agriculture and Life Sciences
• /
• v.8
• /
• pp.107-113
• /
• 1990

This study was attempted to develop a remote controllable speed sprayer in order to protect an operator from agricultural chemicals. For the purpose of remote controllable transmission was developed by using one chip microcomputer. The following results could be summarized in this study. 1. Remote controllable transmission developed had not made even a single mistake during the test performed 100 times repeat. Thus, it could that this machine was very accurate. 2. One chip microcomputer was made by machine language and its was with in 3 sec's which was the same as human did. 3. One chip microcomputer which was used in the experiment could be widely used to automation of agricultural machinery, since it is smaller and chiper than any other similar ones such as personal computer, lap tap, one board computer. 4. Since, farm tractor has the same type of transmission as this system, it also could be adapted to farm tractors. 5. In this experiment, transmission lever was remote controll were designed to operate simultaneously. Thus, this system developed was more complicate than conventional system. However, by removing this transmission lever and by mounting the remote controll system at the speed sprayer, it would be higher and easier to handle than the conventional one.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.5 no.6
• /
• pp.413-417
• /
• 2000

In this study, a direct detection system for triazine derivative herbicides was developed using the photosynthetic reaction center (RC) from the purple bacterium, Rhodobacter sphaeroides, and surface plasmon resonance (SPR) apparatus. The histidine-tagged RCs were immobilized on an SPR gold chip using nickel-nitrilotriacetic acid groups as a binder for one of the triazine herbicide, atrazine. The SPR responses were proportional to the sample concentrations of atrazine in the range 0.1-1 $\mu\textrm{g}$/mL. The sensitivity of the direct detection of atrazine using the RC-assembled sensor chip was higher than that using the antibody-immobilized chip. The other types of herbicides, DCMU or MCPP, were not detected with such high sensitivity. The results indicated the high binding selectivity of the RC complex.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.869-872
• /
• 2005

In this paper we present a switch wrapper for an AMBA AXI, which is an efficient on-chip-network interface compared to bus-based interfaces in a multiprocessor SoC. The AXI uses an idea of NoC to provide the increasing demands on communication bandwidth within a single chip. A switch wrapper for AXI is located between a interconnection network and two IPs connecting them together. It carries out a mode of routing to interconnection network and executes protocol conversions to provide compatibility in IP reuse. A switch wrapper consists of a direct router, AHB-AXI converters, interface modules and a controller modules. We propose the design of a all-in-one type switch wrapper.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.10
• /
• pp.1598-1602
• /
• 2004

In this paper, we report a microthermostat using PDMS (poly-dimethylsiloxane) and glass. This PDMS/glass chip is able to maintain constant temperature that is necessary for restriction enzyme reaction. Since PDMS is the low-cost and the mass-producible material and has very good biochemical compatibility, PDMS chip has more benefit than general Si chip. Heater was made of Au wiring patterned on Pyrex glass. A reaction chamber has a capacity of about 3 ${mu}ell$. We performed a restriction enzyme reaction by using the fabricated microthermostat and conventional method. Then, with the electrophoresis, we made a comparison between the result from the micro reactor and the one from conventional method.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.219-222
• /
• 1991

It is difficult to adapt modern control theory to power conversion system for the price of real time control H/W and the difficulty of S/W implementation. But recent development of large integrated circuit make it possible that One-Chip microprocessor processes high speed arithmatic calculation used in control theory. Specially this chip is called Digital Signal Processing chip. So, this research developes high performance, high reliable digital control system using TMS320C30 of Texas Instrument for real time control in power conversion system.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.3
• /
• pp.186-192
• /
• 1996

A modified learning rule is introduced for the implementation of feedforward artificial neural networks with on-chip learning circuitry using standard analog CMOS technology. Learning rule, is modified form the EBP (error back propagation) rule which is one of the well-known learning rules for the feedforward rtificial neural nets(FANNs). The employed MEBP ( modified EBP) rule is well - suited for the hardware implementation of FANNs with on-chip learning rule. As a ynapse circuit, a four-quadrant vector-product linear multiplier is employed, whose input/output signals are given with voltage units. Two $2{\times}2{\times}1$ FANNs are implemented with the learning circuitry. The implemented FANN circuits have been simulatied with learning test patterns using the PSPICE circuit simulator and their results show correct learning functions.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.292-298
• /
• 1991

A new 6-axis robot controller with a high-speed 32-bit floating-point DSP TMS32OC30 has been developed in Samsung Electronics. The controller composed of Intel 80386 microprocessor for the main controller, and TKS32OC30 DSP chip for joint position controller. The characteristics of the controller are high sampling rate of 200us and fast reponsibility. The main controller supports MS-DOS, kinematics, trajectory planning, and sensor fusion functions which are vision, PLC, and MAP. The one high speed DSP chip is used for controlling 6 axes of a robot in 200us simultaneously. The control law applied is PID controller including a velocity feedforvard in joint position controller. The performance tests, such as command following, CP, were conducted for the controller integrated with a 6 axes robot developed in Samsung Electronics. The results showed a good performance. This controller can also perform the system control with other controllers, the communication with high priority controllers, and visual information processing.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.309-312
• /
• 2001

A primitive gas classification system which can classify limited species of gas was designed and simulated. The 'electronic nose' consists of an array of 4 metal oxide gas sensors with different selectivity patterns, signal collecting unit and a signal pattern recognition and decision Part in PLD(programmable logic device) chip. Sensor array consists of four commercial, tin oxide based, semiconductor type gas sensors. BP(back propagation) neutral networks with MLP(Multilayer Perceptron) structure was designed and implemented on CPLD of fifty thousand gate level chip by VHDL language for processing the input signals from 4 gas sensors and qualification of gases in air. The network contained four input units, one hidden layer with 4 neurons and output with 4 regular neurons. The 'electronic nose' system was successfully classified 4 kinds of industrial gases in computer simulation.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.1 s.14
• /
• pp.5-11
• /
• 2006

One of the most important is to insure that a new circuit design is qualified far release before it is scheduled for manufacturing, test, assembly and delivery. Due to various causes, there happens to be a low yield in the wafer process. Wafer test is a critical process in analyzing the chip characteristics in the EDS(electric die sorting) using analytic tools -wafer map, wafer summary and datalog. In this paper, we propose new analytic map algorithms for DDI chip test data. Using the proposed analytic map algorithms, we expect to improve the yield, quality and analysis time.