• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.1086-1092
• /
• 2015

The off-line and on-line partial discharge (PD) in the stator winding of three high-voltage (HV) motors (1,400 HP, 6.6 kV) is measured and analyzed in this paper. The off-line PD is measured at high values between 24,300 ~ 36,100 pC after 18 years of motor operation. Spare replacement motors were not available for testing the degree of deterioration of the stator windings in standstill status. Therefore, on-line periodic analysis was conducted to monitor the trend of PD after installing a ceramic sensor (110 pF, 6.6 kV) in the terminal box for each phase of each motor. In the stator winding of the No.1 and No.2 HV motors, which showed high magnitudes of off-line PD and low magnitudes of on-line PD, defects are expected to appear in the neutral end of the winding. On the contrary, in the stator windings of the No.3 HV motor, which exhibits high off-line and on-line PD magnitude, defects are expected to appear in the terminal end of the winding where a voltage close to the phase voltage is applied.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권5호
• /
• pp.205-213
• /
• 2001

This paper presents a virtual instrumentation(VI) system for LIMs performance on-line monitoring. The VI is designed using the graphical programming language LabVIEW and is capable of performing on-line measurement functions, including data acquisition, display, and analyses in the time and frequency domains, as well as data archiving. To monitor in real time the steady-state and transient electromagnetic thrust of LIMs, the search coil is used for the determination of the flux linkage components, which is then multiplied by the appropriate current components to yield a signal proportional to the electromagnetic thrust. This paper reports the LIM's dynamics measured by the proposed on-line monitoring system.

• 대한기계학회논문집B
• /
• 제24권10호
• /
• pp.1359-1367
• /
• 2000

In-situ particle monitors(ISPMs) are widely used for monitoring contaminant particles in vacuum-based semiconductor manufacturing equipment. In the present research, the performance of a Particle Measuring Systems(PMS) Vaculaz-2 ISPM at low pressures has been studied. We generated the uniform sized methylene blue particle beams using three identical aerodynamic lenses in the center of the vacuum line, and measured the detection efficiency of the ISPM. The effects of particle size, particle concentration, mass flow rate, system pressure, and arrangement of aerodynamic lenses on the detection efficiency of the ISPM were examined. Results show that the detection efficiency of the ISPM greatly depends on the mass flow rate, and the particle Stokes number. We also found that the optimum Stokes number ranges from 0.4 to 1.9 for the experimental conditions.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.677-682
• /
• 1998

Concrete is an inhomogeneous material consisting of larger aggregates and sand embedded in a cement paste matrix. In this study, an acoustic emission technique has been used to clarify the microscope failure mechanisms of concrete under three point bending test. AE source location has also been done to monitor the activities of internal damage and the progress of microscopic failure path during the loading. The relationship between AE characteristic and microscopic and microscopic failure mechanism is discussed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.269-272
• /
• 2004

The present study used a diagrammatic analysis of 6 sigma quality control and Taguchi method for injection molding process of monitor back-cover, evaluated the influence on the cycle time with part design, mold design, molding process and standardization activity involving design & molding, adopted analysis of sensitivity and effective factors of the part design and molding process conditions for productivity, identified main design molding factors, as critical ones influencing on the quality and productivity, of which is summarized as design guidance. The main contribution factors for cycle time can be sequentially enumerated as follows; hot spot, part thickness, coolant inlet temperature, melt temperature cooling line layout, etc.. As a first step critical factors of the design process of current monitor housing were investigated. And the optimal and better critical factors found in the first step were applied to a new product proving our process was correct. Moldflow software was used for injection molding simulation, and Minitab software for the statistical analysis. Finally, the productivity was increased by about 33 percents for our specific case.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2001년도 International Meeting on Information Display
• /
• pp.9-12
• /
• 2001

With the explosive growth of Note-PC and Desktop monitor market, TFT LCD market confronted a entire supply shortage during 1999. Forecasting a more booming stage for the next several years, many TFT-LCD panel manufacturers continue to expand the capacity of their existing plants and also make an additional investment in building new plants. The new investment is concentrated on the $4^{th}$ generation TFT LCD line in order to improve investment efficiency. The set up of the Samsung's Gen 3.5 line progressed with satisfactorily performance using $600{\times}720mm$ glass size. We have continuously reviewed several issues regarding the glass size for our next Gen. 4 line, which leads to adopt $730{\times}920mm$. Due to the continuous enlargement of a substrate size and following difficulty in transferring cassettes, the next line is expected to be the last line that employs "cassette transfer". The layout of the next line will shift from conventional "concentration-type" to "separation-type" configuration for the purpose of reducing transfer distance as well as transfer time. The details will be discussed in this paper.

• International Journal of Aeronautical and Space Sciences
• /
• 제10권2호
• /
• pp.34-42
• /
• 2009

Gas turbine performance diagnostics is a method for detecting, isolating and quantifying faults in gas turbine gas path components. On-line precise fault diagnosis can promote greatly reliability and availability of gas turbine in real time operation. This work proposes a GUI-type on-line diagnostic program using SIMULINK and Fuzzy-Neuro algorithms for a helicopter turboshaft engine. During development of the diagnostic program, a look-up table type base performance module are used for reducing computer calculating time and a signal generation module for simulating real time performance data. This program is composed of the on-line condition monitoring program to monitor on-line measuring performance condition, the fuzzy inference system to isolate the faults from measuring data and the neural network to quantify the isolated faults. Evaluation of the proposed on-line diagnostic program is performed through application to the helicopter engine health monitoring.

• 한국수학교육학회지시리즈D:수학교육연구
• /
• 제6권1호
• /
• pp.97-106
• /
• 2002

Educators have found that the concept of randomness is often misunderstood by students. Chance recently pointed out that students should be introduced to the concept of randomness through the use of simulations. In this article, we studied various aspects of the probability distribution off linear random path in a circle and introduce some related simulations to guide student exploration and discovery. Consider a random line segment that crosses a circle with a certain radius. Perhaps it can be considered to be a path that an airplane shows up and flies into a random direction in a monitor. What is the expected amount of flying distance through the monitor, and the expected variation\ulcorner Are we monitoring what we see scientifically\ulcorner This article studies the probability distribution and some related aspects of a linear random path within a circular monitor. Some simulative activity is also introduced which can be used in a statistics or probability classes.

• 전기학회논문지
• /
• 제57권9호
• /
• pp.1589-1593
• /
• 2008

The condition of a high voltage motor was monitored with the motor performance monitor (MPM) at the motor control center. The MPM detected defects in the rotor bar and end ring and input power according to motor and load conditions. The assessment of the condition of a coal pulverizer motor indicated it was clearly in good condition in terms of the rotor bars, over voltage, and motor performance. However, the side bands at frequency, 56.48 Hz indicated existence of rotor end-ring fault. The large torque ripple indicated abnormal operating conditions. After visual inspection, it has been observed that an impeller blade of the circulating water pump was broken off causing the irregular torque pattern.

• 소성∙가공
• /
• 제14권4호
• /
• pp.368-374
• /
• 2005

In the present study we used a diagrammatic analysis of 6 sigma quality control and Taguchi method for injection molding of monitor back-cover, evaluated the influence on the cycle time with part design, mold design, molding process and standardization activity involving design and molding, adopted analysis of sensitivity and effective factors of the part design and molding process conditions for productivity, identified main design molding factors. The contributing factors for the final cycle time could be enumerated as follows; the thickness of hot spot, main nominal part thickness, coolant inlet temperature, melt temperature and cooling line layout, etc.. As a first step, all the critical factors of design process applied to the current monitor housing were investigated through 6 sigma process. Thereafter, the optimal and better critical factors found in the first step were applied to new product design to prove that our process was correct. The Moldflow was used for injection molding simulation, and Minitab software for the statistical analysis, respectively. Finally, the productivity of new design was increased about 33 percents for our specific case.