• 조명전기설비학회논문지
• /
• 제22권9호
• /
• pp.17-24
• /
• 2008

최근에 신뢰성 있는 전력공급의 중요성이 증가하고 있다. 이에 따라 전력기기 진단의 중요성 역시 증가하고 있다. 산업설비로 많이 사용되는 고압 회전기는 장기간 사용함에 따라 고정자 권선 절연부분이 열화되어 예상치 못한 절연파괴 사고로 많은 손실을 일으킨다. 이를 진단하기 위하여 고압 회전기 고정자 권선에 접촉식 Capacitive Coupler를 설치하고 부분방전 신호를 계측하여 유지 보수하는 것이 가장 넓게 사용되고 있다. 하지만 현장에서 부분방전 계측 시 노이즈가 혼재된다면 정밀한 부분방전 신호를 계측하는 것이 불가능해진다. 본 논문에서는 국내 수력발전소 중 25년 이상 가동 중인 13[kV]급 수력발전기 고정자 권선에서 160[pF] 용량의 접촉식 Capacitive Coupler를 이용하여 취득한 계측신호를 분석하여 기존 하드웨어적으로만 노이즈를 제거하여도 잔존하는 노이즈를 제거하기 위해 소프트웨어적인 주변신호원과의 관계를 고려한 노이즈제거 기법을 제안하였다.

• 한국지능시스템학회논문지
• /
• 제9권4호
• /
• pp.384-388
• /
• 1999

This paper describes an approach for synthesizing a modularized gain scheduled PD type fuzzy logic controller(FLC) of nonlinear magnetic bearing system where the gains of FLC are on-line adapted according to the operating point. Specifically the systematic procedure via root locus technique is carried out for the selection of the gains of FLC. Simulation results demonstrate that the proposed gain scheduled fuzzy logic controller yields not only maximization of stability boundary but also better control performance than a single operating point (without gain scheduling)fuzzy controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.177-177
• /
• 2000

In this paper, we propose a two-input two-output fuzzy controller to improve the performance of transient response and to eliminate the steady state error. The outputs of this controller are the control input calculated by position-type fuzzy controller and the accumulated error scaling factor. Here, the accumulated error scaling factor is adjusted on-line by fuzzy rules according to the current trend of the controlled process. To show the usefulness of the proposed controller, it is applied to several systems that are difficult to get satisfactory response by conventional PD controllers or PI controllers.

• 한국통신학회논문지
• /
• 제36권11B호
• /
• pp.1389-1393
• /
• 2011

본 논문에서는 자동차, 비행기, 선박 등의 제어시스템과 자동화 라인 컨트롤 시스템 (Product line control system) 그리고 의료 및 산업기기 등 실생활에 광범위하게 쓰이는 Controller Area Network(CAN) 통신을 가시광통신과 연동한 시스템을 구현한다. 가시광통신과 CAN 통신을 위한 응용회로를 개발하였으며 동작원리를 설명하였다. 회로의 Pulse 특성은 송, 수신단 각 부분의 신호 파형으로 보였으며 3m 거리에서 오류 없는 전송 성능 특성을 보였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1889-1892
• /
• 2003

The fabrication of micro-size patterning on alumina substrate is generated by laser direct writing, which has high precision and selectivity of various laser beam energies. The depth and width of patterns is affected by laser parameter such as laser power, scan rate. Through the chemical and mechanical polishing Pd seeds was effectively got rid of alumina substrate for selectivity electroless Ni plating. Thermal treatment is good method for changing electrical property of conductor line, because the treatment can control of the grain size.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1701-1703
• /
• 2002

This paper introduces a on-line monitoring system for insulation diagnosis of high-voltage motor stator windings. This system monitors the insulation condition of the stator winding with sensor, coupling capacitor. Partial discharge (PD) signals are able to be continuously measured and digitalized with a Peak-hold A/D converter to build the database of the high-voltage motor's insulation condition. This system can communicate with the central monitoring system via RS-485 This paper introduces an economic solution for data acquisition of partial discharges.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2066-2068
• /
• 2005

We developed an on-line Ultra-high frequency partial discharge monitoring system to prevent a catastrophic failure of gas- insulated switchgears. The system has been tested in the laboratory for detection of various UHF PD signals. We also performed detection sensitivity verification tests and compared them with conventional IEC60270 method.

• Journal of Electrical Engineering and Technology
• /
• 제11권6호
• /
• pp.1769-1776
• /
• 2016

For on-line partial discharge (PD) monitoring of rotating machines, a novel sensor is proposed, which can be installed on the power lead inside the terminal box of the machine. The sensor has been designed to have high capacitance, and minimal reflection of measured pulses. As a sensitivity of the sensor, transfer impedance $Z_t$ has been measured and compared to conventional coupler-type sensors. A simple method is presented for measuring $Z_t$ of coupler sensors, using a vector network analyzer and a practical lead-cable of rotating machine. Through this method, it became possible to measure the $Z_t$ of coupler sensors including the installation environment of them. The $Z_t$ of the proposed sensor is higher than that of same sized other conventional couplers at frequencies between 30 and 92 MHz. Another sensitivity test has been performed using a PD calibrator as a test pulse source. The proposed sensor has higher measured peak voltage than the conventional coupler type sensors when the same charges were input.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 센서 박막재료
• /
• pp.66-70
• /
• 2001

The partial discharge testing is widely used in diagnostic measuring technology because it gives low stress to power equipment which is undertaken tests. Therefore it is very useful method compare to previous destructive methods and effective diagnosis method in power system that requires on-line/on-site diagnosis. But partial discharges have very complex characteristics of discharge pattern, so it is required continuous research to development of precise analysis method. In recent, the study of partial discharge is carrying out discover of initial defect of power equipment through condition diagnosis and system development of degradation diagnosis using HFPD(High Frequency Partial Discharge) detection. In this study, simulated system is manufactured and HFPD occurred from those simulator is measured with broad-band antenna in real time, the degradation grade of system is analyzed through produced patterns in simulated target according to the AI/statistics processing.

• Journal of Electrical Engineering and Technology
• /
• 제3권4호
• /
• pp.559-565
• /
• 2008

This study designed a new type of loop antenna that is able to detect partial discharges based on microstrip line technology. In the diagnosis of power cables, partial discharge signals are generally produced at a frequency range less than 100MHz because high frequency PD signals are lost along a propagation path in such cables. The new type of loop antenna sensor has been studied using simulation software known as CST microwave studio version 5.0. In partial discharge measurement experiments, a commercial HFCT sensor was used as a reference sensor. Several experiments were made over HFCT and loop antenna sensors for detecting partial discharges on 22.9kV MV XLPE cable. In this study, we showed the loop antenna designed in this study that can be applied as a commercial HFCT sensor.