• 드라이브 ㆍ 컨트롤
• /
• 제18권4호
• /
• pp.84-90
• /
• 2021

Viscosity of hydraulic oils decreases due to loss reduction and efficiency increase of fluid power systems. However, low viscosity is not always appropriate due to the induction of large leakage and small lubricity. Therefore, a detailed study on the optimum viscosity of hydraulic oils is necessary. In this study, based on the thermohydrodynamic lubrication theory, numerical simulation was conducted using the slipper model of swashplate-type axial piston pumps and motors. The viscosity grades' (VG) effects of oils on power losses are mainly discussed numerically in fluid film lubrication, including changes in temperature and viscosity. The simulation results reveal that the flow rate increases and the friction torque decreases as VG decreases. The film temperature and power loss were minimised for a specific oil with a VG. The minimum conditions regarding the temperature and loss were different and closed. Under various operating conditions, the film temperature and power loss were minimised, suggesting that an optimum hydraulic oil with a specific VG could be selected for given operating conditions of pressure and speed. Otherwise, a preferable operating condition must be established to determine a specific VG oil.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2008년도 추계학술대회 논문집
• /
• pp.160-162
• /
• 2008

This paper presents the practical pressure control of hydraulic oil-pump system using SR drive for industrial application. In order to get a high performance of pressure dynamics in actual application, a data based PID control scheme is proposed in this paper. The look-up table from pre-measured data produces an approximately proper current reference according to motor speed and oil-pressure. And, PID controller can compensate the pressure error. With the combination of two references, the proposed control scheme can get a fast dynamics and stable operation. Furthermore, the suitable current controller considering the nonlinear characteristics of SRM(Switched Reluctance Motor) and practical test method for data measuring are introduced. The proposed control scheme is verified by the experimental test.

• Tribology and Lubricants
• /
• 제22권1호
• /
• pp.47-52
• /
• 2006

It is very important to control pressure and flow rate distribution on each component of engine lubrication network. Sometimes many kinds of orifice are used to control flow rate in the hydraulic lubrication field. In this study orifices were adopted on the lubrication network to control oil flow rate distribution. And unsteady transient flow network analysis was carried out to find out the effects of orifices on the engine oil circuit system.

• 드라이브 ㆍ 컨트롤
• /
• 제15권4호
• /
• pp.1-10
• /
• 2018

Spool displacement of a direction control valve is the standard signal to measure the bandwidth frequency of the direction control valve. When the spool displacement signal is not available, it is suggested in this study to use the metering hydraulic line as an alternative way to measure - 90 degree phase bandwidth frequency of the hydraulic direction control valve. Dynamics of the hydraulic line is composed of inertia, capacitance, and friction effects. The effect of oil inertia is dominant in common hydraulic line dynamics and the line dynamics is close to a derivative action in a range of high frequency; such as a range of bandwidth frequency of common directional control valves. Phase difference between spool displacement and line load pressure is nearly constant as a valve close to 90 degree. If phase difference is compensated from the phase between valve input and pressure, compensated phase may be almost same as the phase of spool displacement that is a standard signal to measure phase bandwidth frequency of the directional control valve. A series of experiments were conducted to examine the possibility of using line pressure in to measure phase bandwidth frequency of a directional control valve. Phase bandwidth frequency could be measured with relatively high precision based on metering hydraulic line technique and it reveals consistent results even when valve input, oil temperature, and supply pressure change.

• KSTLE International Journal
• /
• 제8권2호
• /
• pp.29-34
• /
• 2007

Recently, requirements relating to performance, environment and noise in the oil hydraulic system of the heavy construction equipment have been reinforced continuously. In order to solve these technical trends, studies on the system compactness, operation under high pressure and great rotating speed, electronic control, substitute oil, and noise reduction have been progressed briskly. Among these recent studies, the system operation under high pressure is quite difficult to carry into effect due to mechanical limitations; that is, for realizing the system operation in the hydraulic pump under high pressure, the improvements or innovations on the design techniques, the manufacturing techniques, and the lubrication performance of the working oil are required. Accordingly, in this study, the stress distribution and optimum design factors under the maximum pressure were discussed by using stress analysis on the cylinder block of the hydraulic axial piston pump, which is one of the most important relative sliding regions.

• 대한기계학회논문집
• /
• 제16권2호
• /
• pp.191-199
• /
• 1992

This paper presents in experimental study of the dynamic internal pressure within an oil hydraulic vane pump. The measurements of the dynamic internal pressures near the vane of a pressure balance type of an oil hydraulic vane pump with intravanes has been made to provide the essential information for the study of the pump dynamics and control, the pump design and the analysis of tribological problems in the sliding components. The influences of the discharge pressure and rotating speed of the vane on the dynamic pressure in four chambers surrounding a vane have been investigated. The results indicate that the surge pressures of the chambers at the instant moment of discharge and closure are affected by the rotating speed. The pressure in the intravane chamber maintains almost constant values, which remarkably effects the pulsating discharge pressure.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권3호
• /
• pp.369-378
• /
• 1999

This paper presents position control of an electro-hydraulic servo system whoch is operated by four 2-2way high speed on-off valves with either PWM PID control method or sliding mode control method, The advantages of using high speed on-off valves instead of electo-hydraulic servo valves or electro-hydraulic proportional valves are low price robustness for oil contamination and direct control without a D/A converter. The system consists of load cylinder inertia car potentiometer and external load cylinder. The experiments were carried out under several conditions and the results were compared. As a result the sliding mode method has shown good control performance and the robust and stable positioning of the elector-hydraulic servo system can be achieved accurately.

• 한국생산제조학회지
• /
• 제19권1호
• /
• pp.80-88
• /
• 2010

In a conventional system, hydraulic unit pumps out pressurized oil when the power use is not even necessary. As a result, it causes much power loss. This study is on the proposal of new hydraulic unit which controls the revolution of the pump in order to produce proper power needed and to have good response characteristic. In addition, the existing control methods such as PID control method, fuzzy control method, and adaptive control method are applied to the proposed hydraulic unit. Then the best control method is selected and the controller is developed to realize minimum power loss.

• 항공우주시스템공학회지
• /
• 제16권3호
• /
• pp.84-92
• /
• 2022

전기-정유압식 작동기(EHA)는 독립적으로 유동력원을 운용함에 따라, 복잡한 유압 배관을 제거할 수 있어 누유 및 중량 최소화, 안전성 향상의 장점이 있어 최근 항공기용 비행제어 분야에서 사용되고 있다. 이러한 EHA를 탑재하는 항공기의 경우, 기존 중앙 유압시스템을 탑재한 항공기에 비해 제한된 냉각원에 따른 EHA의 열관리 이슈가 대두된다. 이러한 열관리 이슈의 해결을 위해서는, EHA의 열특성을 예측할 수 있는 열해석 모델이 필요하다. 본 연구에서는 유압펌프 및 전기모터로 구성되는 EHA 유압동력모듈의 내부 회전체를 고압 하에서 고속으로 회전이 가능하도록, 유압동력모듈 내부에 유체 순환 회로를 적용하였다. 적합한 열해석 모델을 구축하고, 유냉식 또는 비유냉식 유압동력모듈 적용에 따른 해석 결과의 비교 및 검토를 통해 EHA의 열특성 영향성을 확인하고자 하였다.

• 한국정밀공학회지
• /
• 제5권2호
• /
• pp.33-42
• /
• 1988

In a large scale oil hydraulic system having repeatedly operated actuator, such as a large scale forging press, pressure surges often due to the recombination of oil column in a return line attached to the downstream side of a directional control valve. Expecially, the pressure surges appear very severe ones at a certain valve operating frequency. These pressure surges restrict the operating frequency of the hydraulic system. But related reports on the above mentioned phenomenon are rarely to be found. In this study, therefore, the authors investigate the exact reason why such severe pressure surges occur at a certain range of valve operating frequency. The study is performed by experiment and numerical computation on the relationship between pressure surges and valve operating frequency.