• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.171-171
• /
• 2010

GaN 기반 Light emitting diodes(LEDs)의 p-type doping layer는 일반적으로 hole을 발생시키는 acceptor로 Mg이 사용하되고 있다. 보통 Mg이 도핑된 p-type GaN은 >$1\;{\Omega}{\cdot}cm$의 저항이 존재하는데 그 이유는 Mg의 열적 이온화를 위한 activation 에너지가 높아서 상온에서 valence band의 hole concentration는 전체 억셉터 농도의 1%가 되지 않기 ��문이다. 본 논문에서는 높은 hole 농도를 얻기 위해서 metalorganic chemical-vapor deposition (MOCVD)를 장비를 사용하여 사파이어 기판의 misorientation-angle에 따른 p-type a-plane(11-20) GaN 특성을 분석하였다. misorientation-angle은 c축 방향으로 $+0.15^{\circ}$, $-0.15^{\circ}$, $-0.2^{\circ}$, $-0.4^{\circ}$ off된 r-plane(1-102) 사파이어 기판 을 사용하였다. p-type 도핑물질로 bis-magnesium (Cp2Mg) 소스를 사용하였고 성장 과정중 발생하는 hydrogen passivation으로 인한 Mg-H complexes현상을 해결하기위해 conventional furnace annealing (CFA)와 rapid thermal annealing (RTA)를 이용하여 열처리 공정을 진행하였다. 열처리 공정은 Air와 N2 분위기에서 $650^{\circ}C$에서 $900^{\circ}C$ 사이의 다양한 온도에서 수행하였고 Hall 측정을 위해 Ni을 전극 물질로 사용하였다. 상온에서 Accent HL5500IU Hall system을 사용하여 hole concentration, mobility, specific resistance을 측정하였다. 열처리 공정 후 Hall측정 결과 $+0.15^{\circ}$, $-0.15^{\circ}$, $-0.2^{\circ}$, $-0.4^{\circ}$ off된 각 샘플들은 온도, 시간, 분위기에 따라 hole concentration ($7.4{\times}10^{16}cm^{-3}{\sim}6{\times}10^{17}cm^{-3}$), mobility(${\mu}h=\;1.72\;cm^2/V-s\;{\sim}15.2\;cm^2/V-s$), specific resistance(4.971 ohm-cm ~8.924 ohm-cm) 가 변화됨을 확인 할 수 있었다. 또한 광학적 특성을 분석하기 위해 Photoluminescence (PL)을 측정하였다.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.5
• /
• pp.1-6
• /
• 1997

An analysis method for the electromagnetic scattering of a tE polarized plane wave from a periodic strip grating over a grounded dielectric slab is consisered from the viewpoint of reflectio ngraing problem. The strip gratings showing bragg and off-bragg balzing phenomena at the frequency of 10GHz are designed, respectively. The strip grating structure is implemented using aluminum plate (hround conductor), paraffin(dielectric material ; .xi.$_{\gamma}$=2.24) and copper (strip conductor ; 0.08mm thickness). The experimental results (reflection power) for bragg as well as off-bragg blazing phenomenon have been compared with the theoretical results and fairly good agreements between theory and experiment have been observed.ed.

• Magazine of the Korea Concrete Institute
• /
• v.2 no.1
• /
• pp.79-90
• /
• 1990

The purpose of this paper is to study on the effect of cutting off tension bars in reinforced concrete beams. that is, the ultimate strength, the failure mode and thl} tension stress distribution through the span. To achieve this purpose, a full-scale frame and seven small scale model beams (five rectangular and two T-section beams) were tested. The four main model specimens and two speciml}ns without cutting off tension bars 1,'{ere analyzed as plane stmss element with package program ADINA. As a result of test and analysis, the shorter' distance bet ween the reaction point and the cutting off point, the higher the ultimate strength of a bl}am will be when other physical properties are equal.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.7
• /
• pp.786-795
• /
• 2010

In this paper, we propose a new EBG structure that the two unit cells are connected by the bridge line in signal transmission plane. The SSN of the power plane is reduced effectively by via holes and bridge lines connecting the unit cells. The superior signal transfer characteristic is shown between the signal lines in the signal transmission plane. The proposed EBG structure contains 1.2 GHz cut-off frequency and less than －30 dB suppression in the 8.3 GHz broad bandwidth. In addition, To improve the SI(Signal Integrity) in signal transmission plane keeping the same bandstop frequency range, the optimized location of the reference plane is proposed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.12
• /
• pp.1201-1211
• /
• 2014

The purpose of this paper is to present the aperture cut-off filter for reduction of electromagnetic field penetration through a slot in conducting screen. The reduction characteristics of electric field penetration by the aperture cut-off filter are considered. In order to establish the concept of the aperture cut-off filter, the integral equation on the slot aperture field distribution is derived and solved by method of moments, and the reduction characteristics of penetration electric fields for the incident plane wave are calculated. The numerical results showed that the aperture cut-off filter for reduction of electric field penetration through the slot can be realized. To check the validity of the concept of an aperture cut-off filter and the theoretical analysis, the calculated electric field penetration of the metallic wall with narrow slot were compared with the experimental results.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.2
• /
• pp.101-111
• /
• 2021

Two different types of shear-friction tests were classified by external loadings and referred to as a push-off and a pull-off test. In a pull-off test, a tension force is applied in the transverse direction of the test specimen to produce a shear stress at the shear plane. This paper presents a method to evaluate shear transfer strengths of uncracked pull-off specimens. The method is based on the compression field theory and different constitutive laws are applied in some ways to gain accurate shear strengths considering softening effects of concrete struts based on Modified Compression Field Theory (MCFT) and Softened Truss Model (STM). The validity of the proposed method is examined by applying to some selected test specimens in literatures and results are compared with the predicted values. A general agreement is observed between predicted and measured values at ultimate loading stages in initially uncracked pull-off test specimens. A shear strength evaluation formula considering the effective compressive strength of a concrete strut was proposed, and the applicability of the proposed formula was verified by comparing with the experimental results in the literature.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.12
• /
• pp.1513-1519
• /
• 2013

A genetic algorithm (GA) is an optimization technique based on natural evolution theory to find the global optimal solution. Unlike the gradient-based method, it can design nanoscale structures in the electric field because it does not require sensitivity calculation. This research intends to design a nanoaperture with an unprecedented shape by the topology optimization scheme based on the GA and ON/OFF method in the visible frequency range. This research mainly aims to maximize the transmission rate at a measuring area located 10nm under the exit plane and to minimize the electric distribution at other locations. The finite element analysis (FEA) and optimization process are performed by using the commercial package COMSOL combined with the Matlab programming. The final results of the optimized model are analyzed by a comparison of the electric field intensity and the spot size of near field with those of the initial model.

• Journal of Mechanical Science and Technology
• /
• v.17 no.6
• /
• pp.854-859
• /
• 2003

In this paper, we examine the singular stresses and electric fields in a functionally graded piezoelectric ceramic strip containing an eccentric crack off the center line under anti-plane shear loading with the theory of linear piezoelectricity. It is assumed that the properties of the functionally graded piezoelectric ceramic strip vary continuously along the thickness. Fourier transforms are used to reduce the problem to the solution of two pairs of dual integral equations, which are then expressed to a Fredholm integral equation of the second kind. Numerical values on the stress intensity factor and the energy release rate are obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.1 s.178
• /
• pp.89-96
• /
• 2006

In this study, fabrication of the large area silicon mirror is accomplished by anisotropic wet etching using micromachining technology for implementation of integrated slim optical pickup and the process condition is also established for improving the mirror surface roughness. Until now, few results have been reported about the production of highly stepped $9.74^{\circ}$ off-axis-cut silicon wafers using wet etching. In addition rough surface of the mirror is achieved in case of tong etching time. Hence a novel method called magnetorheolocal finishing is applied to enhance the surface quality of the mirror plane. Finally, areal peak to valley surface roughness of mirror plane is reduced about 100nm in large area of $mm^2$ and it is applicable to optical pickup using infrared wavelength.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.514-517
• /
• 2004

We have studied motion of micro-particle immersed in liquid crystal (LC) controlled by in-plane field, which is an important technology in the electro-phoretic display (EPD). In the EPD on and off states are decided by movement of these charged particles and response time is influenced by moving velocity of charged particles. In addition, the velocity can be controlled by intensity of applied voltage such that the higher the applied voltage, the faster velocity of particles become. In this study, we investigated particles's motion as functions of applied voltage, temperature of LC, rubbing direction,