• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.2
• /
• pp.99-107
• /
• 2006

Magnetic nondestructive testing is very useful far detecting a crack on the surface or near of the surface of the ferromagnetic materials. The distribution of the magnetic flux leakage (DMFL) on a specimen has to be obtained quantitatively to evaluate the crack. The magnetic camera is proposed to obtain the DMFL at the large lift-off. The magnetic camera consists of a magnetic source, magnetic lens, analog to digital converters (ADCs), interface, and computer. The magnetic leakage fields or the distorted magnetic fields from the object, which are concentrated on the magnetic lens, are converted to analog electrical signals tv arrayed small magnetic sensors. These analog signals are converted to digital signals by the ADCs, and are stored, imaged, and processed by the interface and computer. However the magnetic camera has limitations with respect to converting and switching speed, full range and resolution, direct memory access (DMA), temporary storage speed and volume because common ADCs were used. Improved techniques, such as those that introduce the operational amplifier (OP-Amp), amplify the signal, reduce the connection line, and use the low pass filter (LPF) to increase the signal to noise ratio are necessary. This paper proposes the exclusive embedded ADC including OP-Amp, LPF, microprocessor and DMA circuit for the magnetic camera to satisfy the conditions mentioned above.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.1
• /
• pp.44-54
• /
• 2001

In this paper, a novel test method is proposed to detect the hard and soft fault in analog circuits. The proposed test method makes use of the offset voltage, which is one of the op-amps characteristics. During the test mode, CUT is modified to unit gain op-amps with feedback loop. When the input of the op-amp is grounded, a good circuit has a small offset voltage, but a faulty circuit has a large offset voltage. Faults in the op-amp which cause the offset voltage exceeding predefined range of tolerance can be detected. In the proposed method, no test vector is required to be applied. Therefore the test vector generation problem is eliminated and the test time and cost is reduced. In this note, the validity of the proposed test method has been verified through the example of the dual slope A/D converter. The HSPICE simulations results affirm that the presented method assures a high fault coverage.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.6
• /
• pp.87-93
• /
• 2019

We discuss the design of a radiometer using a millimeterwave(Ka-band) seeker. We applied a total power radiometer, thus the radiometer is composed of a IF-drive amp, band-pass filter, detector and an Op-amp additionally. As a radiometer measure a radiated signal of an object which is noise-like, a radiometer is easily affected by the variance of system temperature. To mitigate an adverse effect, we propose a compensation method in a radiometer without brightmess temperature compensation circuits. Through some experiments such like a distinction a target and the background, we have verified that the designed radiometer system has distingushed a car from the ground completely.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.9
• /
• pp.912-917
• /
• 2006

A strain gauge weight measuring instrumentation system was designed with RF sensor network facilities. In the sensor module system data conversion and a series of signal processing were totally equipped. 16 strain gauges are incoming sensors and each output of the strain gauge was amplified and filtered for proper analog signal processing. Several measuring instrumentation OP amps and general purposed OP amps were used. 12 bits A/D converters converted analog signals to digital bits and a PIC microprocessor controlled the 16 channels of strain gauges. RF RS232 modules were used for wireless communication between the PIC microprocessor and an Ethernet host far a remote sensor monitoring system development.

• KIPE Magazine
• /
• v.9 no.3
• /
• pp.23-27
• /
• 2004

ADuC84x는 OP-AMP 아날로그-디지털 컨버터(ADC), 디지털-아날로그 컨버터(DAC)로 유명한 ADI(아날로그 디바이스사)의 8비트 임베디드 마이크로콘트롤러인 마이크로컨버터이다. ADI의 마이크로컨버터 ADuC84x는 산업용 정밀제어 및 계측용 애플리케이션의 고성능 신호처리를 위해 설계된 프로그래머블 고속 임베디드 마이크로콘트롤러이다.(중략)

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.141-144
• /
• 2002

Several charge Injection compensation circuits, such as, the dummy transistor circuit, the switched OP-amp circuit, the switched capacitor circuit, were fabricated and the test results were compared. The differences between SPICE simulation results and measurements were within around 10%.

• Journal of the KSME
• /
• v.25 no.2
• /
• pp.130-136
• /
• 1985

확정적 계측신호에 극한시키며 현장 혹은 연구실에 종사하고 있는 기계기술자에게 필요로 하는 애널로그계측과 디지틀계측의 특성과 계측시스템의 구성, 연산증폭기(Op. Amp)의 원리 및 응용, 측정신호의 선형화, 마이크로 프로세서의 원리 A/D, D/A 변환기의 원리 및 응용, 자료처리시 스템, 센서의 원리 및 응용, 디지틀계측시스템의 최근동향등 메카트로닉스시대에서 요청되는 계 측공학의 주요과제에 대하여 기술한다.

• Proceedings of the IEEK Conference
• /
• 2002.06d
• /
• pp.365-368
• /
• 2002

In this paper, we present a low cost circuit design for a sentence speech recognition. The basic circuit of the designed sentence speech recognizer is composed of resistor, capacitance, OP Amp, counter and logic gates. Through a sentence recognition experiment, we can find the effectiveness of the designed sentence recognition circuit

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.574-575
• /
• 2012

LP 레코더로 부터 음향신호를 검출하는 MM 카트리지와 포노 앰프의 연결 케이블의 기능을 분석하고 평탄 주파수 특성을 위한 최적 길이를 결정하였다. RG-58 동축 케이블이 MM카트리지 연결에 적합함을 보이고 OP-amp로 RIAA 필터를 구성하고 케이블 길이에 따른 음색변화를 확인하였다.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1263-1265
• /
• 2004

RF-ID system is one of the very interesting field not only in a technical and economical point of view but also that people are still trying to realize lossless power transmission. This paper has a purpose on the efficient power transmission at the passive type IDcard by using wireless power transmission system. The most difficult but important part of the passive type RF-ID system is building the system that supplies power from Reader-antenna to IDcard-antenna. To check what is the most efficient way to deliver power depending on what kind of specifications of the power-amp in reader, antenna and antenna in IDcard is for operating IDcard circuit efficiently receiving the power from reader-antenna. For this, we used 125kHz sinewave for RF signal as a basic specification, OP-amp for amplifying signal and power-amp for amplifying power, loop type antenna.