• 한국신뢰성학회지:신뢰성응용연구
• /
• 제13권2호
• /
• pp.99-107
• /
• 2013

One-shot device is required to successfully perform its function only once at the moment of use. The reliability of a one-shot device should be expressed as a probability of success. In this paper, we propose a bayesian approach for estimating reliability of one-shot devices with small sample size. We employ a gamma prior to obtain the posterior distribution. Finally, we compare the accuracy of the proposed method with general maximum likelihood method.

• 한국항공우주학회지
• /
• 제35권5호
• /
• pp.419-425
• /
• 2007

수직발사를 위한 스트랩다운 관성항법시스템의 급속 One-Shot정렬 기법을 제시한다. 제시된 정렬기법은 종 항법시스템(Slave INS)의 가속도계 출력 값 및 주 항법시스템(Master INS)의 자세를 이용한다. 또한 정렬 성능 및 속도를 개선시키기 위하여 등가선형변환 및 사전 필터링 기법을 제시한다. 시험결과들은 제시된 방법이 정렬 정확도 및 정렬 속도 개선에 효과적임을 보였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권4호
• /
• pp.426-435
• /
• 2005

The lightness of components required in automobile and machinery industries is requiring high strength of components. Therefore this requirement is accomplished as the process of shot-peening method that the compressive residual stress is made on the metal surface as one of various improvement methods. Special research is, therefore, needed about compressive residual stress on the metal surface in the process of shot-peening method. Therefore, in this paper the effect of compressive residual stress of spring steel(JISG SUP-9) by shot-peening on fatigue crack growth characteristics in environmental condition(temperature) and mechanical condition(shot velocity, stress ratio) was investigated with considering fracture mechanics. By using the methods mentioned above, the following conclusions have been drawn. (1) The fatigue crack growth rate(da/dN) of the shot-peened material was lower than that of the un-peened one. In high temperature range. fatigue crack growth rate decreased with increasing temperature range, while fatigue crack growth rate increased by decreasing temperature in low temperature. (2) Fatigue life shows more improvement in the shot-peened material than in the un-peened material. And compressive residual stress of surface on the shot-peen processed operate resistance force of fatigue crack propagation.

• 한국항행학회논문지
• /
• 제22권6호
• /
• pp.500-506
• /
• 2018

본 논문에서는 유도탄의 정확한 자세를 알기 위해 주 관성항법장치와 유도탄 내부 관성항법장치를 이용하는 one-shot 정렬에 대해 고려하였다. One-shot정렬을 수행하기 위해서는 주 관성항법장치와 부 관성항법장치 사이의 비정렬각을 구해야 되는데, 장입유도탄과 부 관성항법장치 사이의 비정렬각을 구하여 보상하면 된다. 비정렬각은 장입유도탄의 롤 회전을 이용하여 산출되며, 장입유도탄을 회전하기 위한 정렬용 치구, 장입유도탄의 수평 상태를 측정하기 위한 수평각도계와 인터페이스 구조물이 제작되었다. TAS(tilt angle save) 점검 결과, 비정렬각 ${\alpha}$, ${\beta}$, ${\gamma}$ 값이 정상 범위이며 이 값을 보상하여 one-shot 정렬을 수행할 수 있다.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제54권11호
• /
• pp.669-672
• /
• 2005

An algorithm detecting abrupt and gradual shot boundaries is proposed in this Paper. The conventional methods detect abrupt shot boundaries well, but do not show good performance on gradual shot boundaries. The proposed method Is based on the fact that the difference of the characteristic between frames is large when the shot conversion occurs. And the Proposed method detects abrupt and gradual shot boundaries with one algorithm. Moreover, it detects not only position where gradual shot conversion occurs, but also the exact duration where gradual shot conversion occurs.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제16권1호
• /
• pp.32-40
• /
• 2016

Purpose: The purpose of this study is to analyze the effect of sampling points on accuracy of storage reliability estimation for one-shot systems by assuming a weibull distribution as a storage reliability distribution. Also propose method for determining of sampling points for increase the accuracy of reliability estimation. Methods: Weibull distribution was divided into three sections for confirming the possible to estimate the parameters of the weibull distribution only some section's sample. Generate quantal response data for failure data. And performed parameter estimation with quantal response data. Results: If reduce sample point interval of 1 section, increase the accuracy of reliability estimation although sampling only section 1. Even reduce total number of sampling point, reducing sampling time interval of the 1 zone improve the accuracy of reliability estimation. Conclusion: Method to increase the accuracy of reliability estimation is increasing number of sampling and the sampling points. But apply this method to One-shot system is difficult because test cost of one-shot system is expensive. So propose method of accuracy of storage reliability estimation of one-shot system by adjustment of the sampling point. And by dividing the section it could reduce the total sampling point.

• 대한산업공학회지
• /
• 제36권4호
• /
• pp.212-218
• /
• 2010

This paper shows accuracy comparison results of reliability estimation methods for one-shot systems with respect to sample sizes. To compare accuracy in reliability estimation methods, quantal-response data, characterizing one-shot systems, were simulated using failure times of LED obtained through the accelerated life test, and then the true reliability over time was evaluated using the failure times. The simulated quantal-response data were used to estimate the true reliability through applying reliability estimation methods in open literature. Accuracy of each reliability estimation method was compared in terms of both SSE (Sum of Squared Error) and MSE (Mean Squared Error), and then estimation trend for each method is found. Feasible bounds which true reliability would exist within were estimated through applying the found trends to quantal-response data set of a real weapon system.

• 산업진흥연구
• /
• 제7권4호
• /
• pp.1-8
• /
• 2022

우리 주위를 살펴보면 한 번 사용하고 버리는 일회용품이 많다. 폭죽이나 탄약과 같은 일회용품이 대표적인데 이들 일회용품은 제조 후 한 동안 저장되어 있다가 필요한 때 사용하고 나면 폐기처분하게 된다. 하지만 이런 일회용품은 일반 운영장비와 달리 신뢰성평가가 제대로 이루어지지 못했다. 이에 본 연구에서는 일회용품 중에서 탄약에 대한 저장탄약신뢰성프로그램을 통해 탄약의 경우 신뢰성 확보를 위해 정부에서 어떤 일을 하는지 먼저 살펴본다. 이어서 통계분석적인 측면에서 탄약과 같은 일회용품에 대한 신뢰성분석 방안으로 어떤 것이 있는지 알아본다. 구체적으로 통계학에서 로트의 품질수준을 파악하는 샘플링검사를 활용하여 일정한 시기에 생산된 탄약에 대한 신뢰성의 수준을 파악할 수 있다. 본 연구에서는 KS Q0001인 계수규준형 1회 샘플링검사표를 이용할 수 있음으로 보여준다. 다음으로 탄약의 저장신뢰도를 파악할 수 있는 방법으로 비모수적인 방법과 모수적인 방법을 소개한다. 비모수적인 방법중에서 특히 Kaplan-Meier 방법은 중도중단데이터가 포함된 경우에도 활용될 수 있다. 마지막으로 모수적인 방법 중에는 신뢰성분석에 많이 활용되는 와이블분포가 탄약의 저장신뢰도를 파악하는 데에도 활용될 수 있다.

• 시스템엔지니어링학술지
• /
• 제16권1호
• /
• pp.1-8
• /
• 2020

In this paper we proposed to develop the reliability growth planning for the One-shot system using the PM2-Discrete model. The PM2-Discrete is the methodology specifically developed for discrete systems and is the first quantitative method available for formulating detailed plans in the discrete usage domain. First, the parameters RG, RI, T, MS and d of the PM2-Discrete model are set. Second, the case analysis was performed on One-shot system A. Third, the input parameter values were applied to drive the R(t) equation. Finally, using RGA 11 Software, the reliability Growth Planning Curve of One-shot system A was constructed. Also, the sensitivity analyses are performed for the changes of model parameters. The results of this study can be usefully used in establishing the reliability growth planning curve of the One-shot system.

• 한국정밀공학회지
• /
• 제34권2호
• /
• pp.151-156
• /
• 2017

Shot peening is widely used to improve the fatigue life and strength of various mechanical parts and an accurate method is important for the prediction of the compressive residual stress caused by this process. A finite element (FE) model with an elliptical multi-shot is suggested for random-angled impacts. Solutions for compressive residual stress using this model and a normal random vertical-impact one with a spherical multi-shot are obtained and compared. The elliptical multi-shot experimental solution is closer to an X-ray diffraction (XRD) than the spherical one. The FE model's peening coverage also almost reaches the experimental one. The effectiveness of the model based on an elliptical shot ball is confirmed by these results and it can be used instead of previous FE models to evaluate the compressive residual stress produced on the surface of metal by shot peening in various industries.