• Proceedings of KOSOMES biannual meeting
• /
• 해양환경안전학회 2017년도 추계학술발표회
• /
• pp.93-94
• /
• 2017

• Resources Recycling
• /
• 제4권4호
• /
• pp.12-15
• /
• 1995

In this paper, some representative waste tire pyrolysis were investigated together with the analysis of the problems associated with the commercialization of various waste tire treatment technologies. Also, R & D results on recovering the oil from the pyrolysis of waste tires, when waste oil was used as a heating medium, were summarized in this study. Experimental results show that the present pyrolysis process has both lower pyrolytic temperature and higher pyrolysis rate than usual one and that the quality of the product oil and residue obtained was relatively even with large availability.

• Journal of the Korean Society of Safety
• /
• 제12권2호
• /
• pp.22-26
• /
• 1997

A small scale centrifugal oil separator consisted of two concentric tubes was fabricated for spilt oil recovery. With speed control of the inner tube, its performance of oil separation was investigated. Oil-water mixture is separated by forced vortex motion with the rotating inner tube. Velocity and pressure distributions in the tubes were calculated. Control of rotating speed, which is the most influencing parameter, showed an optimum value 946rpm corresponding to the acceleration of 20g at the inner tube surface. Separation performance was suddenly deteriorated at rotating speed higher than 1200rpm.

• Tribology and Lubricants
• /
• 제13권2호
• /
• pp.46-51
• /
• 1997

Crosshead bearings in two-stroke marine diesel engines are operated under severe conditions of lubrication because the load on the bearing is unidirectional and the sliding speed is very low and oscillatory. In this paper, the motion of journal in a bearing is investigated using the lubrication theory. Several locus paths are presented to show the effects of oil groove size, bearing clearance and oil inlet pressure. It is found that the minimum film thickness is affected by the oil groove and bearing clearance, and the oil groove is an important design factor.

• Applied Microscopy
• /
• 제50권
• /
• pp.21.1-21.3
• /
• 2020

Sample preparation is significantly important to the high-resolution transmission electron microscopy (HRTEM) characterization of nanomaterials. However, many general organic solvents can dissolve the necessary organic polymer support layer in TEM grid, which causes it difficult to obtain high-quality samples of oil-soluble nanomaterials. In this study, a new sample preparation method for oil-soluble nanomaterials has been developed by using the sublimable material as a transition layer. Experiments also show that there is no damage to TEM grids and high-quality HRTEM images can be obtained via this method. This approach paves the way to applicable HRTEM sample preparation of oil-soluble nanomaterials.

• 한국석유지질학회:학술대회논문집
• /
• 대한자원환경지질학회/한국석유지질학회/한국암석학회 2000년도 추계공동학술발표회 초록집
• /
• pp.49-49
• /
• 2000

• 한국석유지질학회:학술대회논문집
• /
• 한국석유지질학회 2000년도 제7차 학술발표회 발표논문집
• /
• pp.6-6
• /
• 2000

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 한국항해항만학회 2002년도 춘계학술대회논문집
• /
• pp.73-87
• /
• 2002

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.414-419
• /
• 2000

This paper presents the knowledge and information construction trends in the oil industry. The investigated results show that the website construction and e-business level in oil industries including oil circulation distributors are very low and introduction stage compared with those of other industries.

• Economic and Environmental Geology
• /
• 제44권1호
• /
• pp.83-94
• /
• 2011

Extra heavy oil reservoirs are distributed over the world but most of them is deposited in the northern part of the Orinoco River in Venezuela, in the area of 5,500 $km^2$, This region, which has been commonly called "the Orinoco Oil Belt", contains estimated 1.3 trillion barrels of original oil-in-place and 250 billion barrels of established reserves. The Venezuela extra heavy oil has an API gravity of less than 10 degree and in situ viscosity of 5,000 cP at reservoir condition. Although the presence of extra heavy oil in the Orinoco Oil Belt has been initially reported in the 1930's, the commercial development using in situ cold production started in the 1990's. The Orinoco heavy oil deposits are clustered into 4 development areas, Boyaco, Junin, Ayachoco, and Carabobo respectively, and they are subdivided into totally 31 production blocks. Nowadays, PDVSA (Petr$\'{o}$leos de Venzuela, S.A.) makes a development of each production block with the international oil companies from more than 20 countries forming a international joint-venture company. The Eastern Venezuela Basin, the Orinoco Oil Belt is included in, is one of the major oil-bearing sedimentary basins in Venezuela and is first formed as a passive margin basin by the Jurassic tectonic plate motion. The major source rock of heavy oil is the late Cretaceous calcareous shale in the central Eastern Venezuela Basin. Hydrocarbon materials migrated an average of 150 km up dip to the southern margin of the basin. During the migration, lighter fractions in the hydrocarbon were removed by biodegradation and the oil changed into heavy and/or extra heavy oil. Miocene Oficina Formation, the main extra heavy oil reservoir, is the unconsolidated sand and shale alternation formed in fluvial-estuarine environment and also has irregularly a large number of the Cenozoic faults induced by basin subsidence and tectonics. Because Oficina Formation has not only complex lithology distribution but also irregular geology structure, geological evolution and characteristics of the reservoirs have to be determined for economical production well design and effective oil recovery. This study introduces geological formation and evolution of the Venezuela extra heavy oil reservoirs and suggest their significant geological characteristics which are (1) thickness and geometry of reservoir pay sands, (2) continuity and thickness of mud beds, (3) geometry of faults, (4) depth and geothermal character of reservoir, (5) in-situ stress field of reservoir, and (6) chemical composition of extra heavy oil. Newly developed exploration techniques, such as 3-D seismic survey and LWD (logging while drilling), can be expected as powerful methods to recognize the geological reservoir characteristics in the Orinoco Oil Belt.