• 대한방사선기술학회지:방사선기술과학
• /
• 제26권2호
• /
• pp.49-56
• /
• 2003

초음파 Q/A팬텀은 조직등가물질(TMM)과 표적물질로 구성한다. 표적물질은 데드존, 거리분해능, 측분해능, 수직과 수평거리 정확성 등을 평가하는 모노필라멘트로 TMM과 조화를 이뤄 선명하게 나타나야 한다. 본 연구의 목적은 금속성 모노필라멘트와 나일론 모노필라멘트를 이용하여 TMM 내에서 최적의 해상력을 표현할 수 있는 선 표적물질을 얻기 위해 탈기수와 C15 g TMM을 합성하여 모노필라멘트를 설치하고 SONOACE 6000C $3.5{\sim}7.5\;MHz$를 주사하여 다음과 같은 결론을 얻었다. 1. 0.1 mm 금속성 모노필라멘트와 0.12 mm, 180데너아 나일론 모노필라멘트에서 점상의 선명한 에코양상을 관찰할 수 있었다. 2. 0.2 mm 금속성과 나일론 모노필라멘트는 다중반사에 의한 혜성꼬리음영이 관찰되었다. 3. 데드존과 거리분해능은 0.1 mm 나일론 모노필라멘트가 유용한 것으로 나타났다. 4. 나일론 모노필라멘트는 금속성 모노필라멘트에 비해 견고성과 수축성이 우수하여 팬텀제작에 유리한 것으로 나타났다. 5. TMM의 경도 차가 모노필라멘트의 에코 양상에 많이 관여하지 않는 것으로 나타났다.

• 한국항공우주학회지
• /
• 제46권10호
• /
• pp.867-875
• /
• 2018

종래의 큐브위성용 나일론선 절단방식 태양전지판 구속분리장치는 단순히 패널 평면상에 나일론선을 체결함에 따른 취약한 구속력으로 인해 태양전지판 면적이 증가함에 따라 발사하중에 대한 구조 건전성 확보에 한계가 존재한다. 본 연구에서는 전술한 종래 분리장치의 한계점 극복을 위해 Ball & Socket 접속부가 반영된 별도의 타원형 브라켓을 적용하여 높은 구속력, 전개 및 평면 방향 동시구속 및 체결작업의 용이성 등의 장점을 갖는 6U 큐브위성용 태양전지판 구속분리장치를 제안하였다. 상기 구속분리장치의 설계 방향성 파악을 위해 큐브위성용 태양전지판 조립체에 대한 발사하중을 고려한 구조해석을 실시하였다. 또한, 상이한 온도조건에서의 나일론선 두께 및 체결횟수에 따른 기능시험을 수행하여 제안된 구속분리장치의 유효성을 검증하였다.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1235-1244
• /
• 1994

In this study, experimental results of the nucleate boling of wire-wrapped tubes are provided. Both water and R-113 were boiled. Solid stainless steel wires, stranded copper wires and stranded nylon wires were tested. Solid stainless wire is effective to enhance the boiling of water. The performance is approximately the same(or slightly better at certain conditions) as that of GEWA-T tubes. For the test range of wire diameter 0.6 $mm{\le}d{\le}2.6 mm$, the optimum gap width increases as the wire diameter increases. The maximum heat transfer coefficient was obtained for the 1.0 mm diameter wire, and it is 1.6 times larger than that of the GEWA-T at the heat flux of 20 $kW/m^{2}.$ Solid stainless wire is also effective to enhance the boling of R-113 at low heat fluxes. The performance of the wire-wrapped tube approaches that of GEWA-T. At high heat fluxes, however, the enhancement decreases. The reason may be attributed to the cavity shape and the high wettability of the refrigerants. Stranded copper or nylon wire is effective to enhance the boiling of R-113. The performance is approximately the same(or slightly better) as that of GEWA-T tubes. Maximum heat transfer was obtained for the stranded nylon wire, and it is approximately 1.4 times larger than that for the GEWA-T at the heat flux of 20 $kW/m^{2}.$ The reason may be atrributed to the favorable thermal environment in the restricted regions formed by twisted wires.

• 한국기계가공학회지
• /
• 제21권5호
• /
• pp.1-8
• /
• 2022

Fused deposition modeling (FDM), based on stacking a continuous filament of polymer or composite materials, is well matured and is thus widely used in additive manufacturing technology. To advance FDM-based 3D printing technology, the mechanical properties of additively manufactured composite materials must be improved. In this study, we proposed a novel FDM 3D printing process using metal wire-polymer composites, enabling enhanced mechanical properties. In addition, we developed a new type FDM filament of copper wire wrapped in nylon material for stable 3D printing without thermal damage during the printing process. After FDM printing of the copper wire-nylon composite filament, we conducted a tensile test to investigate the mechanical behavior of the printed composite materials. The experimental results confirmed that the tensile strength of the 3D-printed metal wire-polymer composites was higher than that of the conventional single polymer material. Thus, we expect that the FDM printing process developed in this study may be promising for high-load-bearing applications.

• 항공우주시스템공학회지
• /
• 제15권4호
• /
• pp.1-6
• /
• 2021

The non-explosive holding and release mechanism is used to prevent damage to the mission component caused by explosives when the deployment structure for Cube Satellites is separated. However, among the several types available, the non-explosive holding and release mechanism system using nylon wires depend on the nylon wire knot method and tightening power of the worker. Therefore, in this study, we conducted experiments with the operation of a new holding and release mechanism system by conceptualizing the Boa System Dial, which can provide a constant tightening force regardless of worker proficiency and deploying a imitational solar panel. In this study, the process of binding and unbinding with constant tension was recorded while applying the novel non-explosive holding and release mechanism using the Boa System Dial proposed. In addition, required advances are indicated for the application of the proposed system to actual Cube Satellites.

• Journal of Biosystems Engineering
• /
• 제28권3호
• /
• pp.209-216
• /
• 2003

Red pepper calyx cutting devices using a impacting force by a rotational cutter were devised and tested to obtain the fundamental data for development of a calyx removal unit. Fresh red peppers with 80∼87%(w.b.) of initial moisture contents were used as experimental materials. Square and wire type of rotational cutters were used to cut the red pepper calyx and the fresh red peppers were fed into the device both manually and automatically. Three rotational speeds of 250, 500, 700rpm were selected for a square, and 1000, 1500, 1800rpm for a wire type cutter respectively. Four types of red pepper fixing unit were used in manual feeding. The cutting rate of the square type cutter was over 50% regardless the shape and specification of the cutter. For the wire type cutter, the copper wire and nylon chord could not be applied to cut the red pepper calyx because of the low cutting rate. But for the fine wire, the cutting rate was higher and the cutting mechanism was more steady than copper wire and nylon chord. The cutting rate of automatic feeding and wire type cutting unit was about 70% for all levels of the rotational speed. The cutting rate was highly related to the impacting point of red pepper in carrier box. To increase the cutting rate using the rotational cutter, a proper device and mechanism was required to keep the impacting point consistently.

• 타이어
• /
• 통권22호
• /
• pp.17-24
• /
• 1969

• 항공우주시스템공학회지
• /
• 제15권5호
• /
• pp.81-88
• /
• 2021

일반적으로 큐브위성용 전개형 태양전지판을 수납 및 전개시키기 위해 사용되는 구속분리장치는 비폭발식 나일론선 절단방식이 적용된다. 그러나 상기 방식은 태양전지판 수납 상태에서 큐브위성의 배터리 충전, PCB 및 탑재체의 전기적 점검 및 시험 등을 위한 접근 포트 연결 시 분리장치의 구속해제 및 재채결 작업이 반복적으로 요구된다. 따라서, 기존의 구속분리장치는 위성체 내부 접근을 위해서는 작업자의 번거로움 및 일관된 나일론선 체결작업 공정 유지의 어려움이 존재한다. 본 연구에서는 나일론 선 절단 없이 구속 핀 분리만으로 자유롭게 태양전지판 전개 및 수납이 가능한 Pin-puller형 태양전지판 구속분리장치를 제안하였으며, 기능 및 성능검증을 위한 분리장치의 전개시험 및 최대 분리하중 측정 시험을 통해 분리장치 설계의 유효성을 입증하였다.

• Journal of Trauma and Injury
• /
• 제20권2호
• /
• pp.72-76
• /
• 2007

Purpose: The purpose of this clinical trial was to evaluate the fixation method for treating alveolar fractures in an emergency department. Methods: The efficiency of using the fixation method was judged on the basis of clinical criteria. Stability, occlusion state, bleeding amount after fixation, operation time, and difficulties during procedural operation were recorded. Results: Eight patients were enrolled in this study. In all instances, the fixation method was effective in bleeding control. Each patient had a noticeable decrement in bleeding. A wire was used for four of the eight patients, and nylon strings was used for the others. The average operation time was 6.3 minutes for the wire patients and 2.8 minutes for the Nylon string patients. No specific problem was identified during the procedural operation. However, the difference in the fixation material influenced the effectiveness of the procedure, the operation time, and the satisfaction of the doctor. Conclusion: In the emergency department, the fixation method using wire or nylon string in the treatment of alveolar fractures is effective in bleeding control

• 항공우주시스템공학회지
• /
• 제12권5호
• /
• pp.69-75
• /
• 2018

본 논문에서는 전기 접속부 역할을 하는 포고핀을 활용한 극초소형 위성용 나일론선 절단방식 태양전지판 분리장치를 제안하였다. 제안된 분리장치는 종래 나일론선을 이용한 분리장치에 비해 높은 체결력 및 횡/종방향 동시구속이 가능하고, 체결작업이 용이하며, 또한 다수의 태양전지판의 동시분리가 가능한 장점을 갖는다. 또한 제안된 분리장치에 적용된 포고핀은 전력공급을 위한 전기 접속부 기능과 함께 전개 상태 스위치 및 태양전지판의 분리 스프링 역할이 동시에 가능하다. 본 논문에서는 제안된 포고핀 분리장치의 기능성 입증을 위해 체결횟수에 따른 분리 기능시험을 통해 기능성을 검증하였다.