• Fibers and Polymers
• /
• v.5 no.2
• /
• pp.145-150
• /
• 2004

Blends of poly(phenylene sulfide) (PPS) and polyethylene, either linear low density polyethylene (LLDPE) or metallocene-catalyzed polyethylene (MPE), that were prepared by melt blending, were investigated. From the rheological properties as determined by capillary rheometry, the melt viscosity of both PPS/LLDPE and PPS/MPE blends was low when PE was in dispersed phase, but high melt viscosity was observed for both blends with PPS in dispersed phase. Significant differences depending on the composition were found in the mechanical properties such as percent elongation at break and notched Izod impact strength. In addition, dispersed phase morphology of the blends was analyzed by a scanning electron microscope (SEM), together with brief discussion about the difference between them.

• Computers and Concrete
• /
• v.19 no.4
• /
• pp.375-385
• /
• 2017

In the present paper experimental and numerical analysis of hook-ended steel fiber reinforced concrete is carried out. The experimental tests are performed on notched beams loaded in 3-point bending using fiber volume fractions up to 1.5%. The numerical analysis of fiber reinforced concrete beams is performed at meso scale. The concrete is discretized with 3D solid finite elements and microplane model is used as a constitutive law. The fibers are modelled by randomly generated 1D truss finite elements, which are connected with concrete matrix by discrete bond-slip relationship. It is demonstrated that the presented approach, which is based on the modelling of concrete matrix using microplane model, able to realistically replicate experimental results. In all investigated cases failure is due to the pull-out of fibers. It is shown that with increase of volume content of fibers the effective bond strength and slip capacity of fibers decreases.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.389-394
• /
• 2001

The notched Charpy and Izod impact tests arc the most prevalent techniques used to characterize the effects of high impulse loads on ploymeric materials. An analysis method for rubber toughened PVC is suggested to evaluate critical strain energy release rates(Gc) from the Charpy impact energy measurements. An Instrumented Charpy impact tester was used to extract ancillary information concerning fracture properties in addition to total fracture properties and maximum critical loads. The stress intensity factor Kd was computed for varying amounts of rubber contents from the obtained maximum critical loads and also toughening effects were investigated as well.

• Journal of Welding and Joining
• /
• v.17 no.3
• /
• pp.96-101
• /
• 1999

Microstructures and mechanical properties of weldments were studied for EH36 TMCP higher-strength hull steel with electrogas welding jprocess. In case of a newly designed EH36 TMCP steel for large heat input welding process, the Microstructures of HAZ shows more narrow width of grain coarsed region than that of conventional EH36 TMCP weldments, the amount of acicular ferrite, which is beneficial to impact toughness, increased while the amount of grain-boundary ferrite decreased. Charpy V-notched impact tests show that a newly designed EH36 TMCP steel weldment satisfies all the requirement of specifications, especially at the fusion line +2mm where the conventional EH36 TMCP steel fails to exceed the requirement.

• Elastomers and Composites
• /
• v.50 no.3
• /
• pp.205-209
• /
• 2015

Magnesium oxide (MgO) reinforced polyamide-66 (PA66) composites were prepared through melt-compounding method in order to determine the possibility of using MgO particle as conductive filler in the polymer-based composite. The effects of MgO filler content on the thermal conductivity and mechanical properties for the PA66/MgO composites were investigated. The results showed that the addition of MgO filler to the PA66 matrix led to a large increase in thermal conductivity of the PA66/MgO composites. Tensile strengths of the PA66/MgO composites were slightly decreased as MgO filler loading increased. However, flexural strength and flexural modulus were improved with increasing filler loading. Notched Izod impact strengths were dramatically lowered by the addition of MgO filler.

• Structural Engineering and Mechanics
• /
• v.91 no.3
• /
• pp.239-250
• /
• 2024

With the aim to provide better predication about fracture behavior, a numerical simulating strategy based on the rigid spring model is proposed for reinforced concrete (RC) structures in this study. According to the proposed strategy, concrete is partitioned into a series of irregular rigid blocks based on the Voronoi diagram, which are connected by interface springs. Steel bars are simulated by bar elements, and the bond slip element is defined at bar element nodes to describe the interaction between reinforcement and concrete. A concrete damage evolution model based on the separation criterion is adopted to describe the weakening process of interface spring between adjacent blocks, while a nonlinear bond slip model is introduced to simulate the synergy behaviour of reinforced steel bars and concrete. In the damage evolution model of concrete, the influence of compressive stress perpendicular to the interface on the shear strength is considered. To check the effectiveness and applicability of the proposed modelling, experimental and numerical studies about a simply-supported RC beam and the two-notched concrete plates in Nooru-Mohamed's experiment are conducted, and the grid sensitivity are investigated.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.1
• /
• pp.131-141
• /
• 1994

This experimental study was performed to lnvestigate the effects of the lergths dnd volume contents of glued hooked steel fiber for the fracture toughness and strength of c oncretc. The notched steel fiber reinforced concrete beams with different flber length(30, 60mm) and fiber volume content(O.0, 0.5, 1.0, 1.5, 2.0%) were tested under 3-point benclmg, md 1 he flexural strengths, fracture energy and CMOD were obtained from the experimental data. The fracture energy v~ds used as d means to evaluate the fracture toughness ot concrete. The results showed that the frdcture toughness and 5trength of conuett. were generally increased ds the content of steel fiber was inc~edsed, arid the length of steel ilber had a great efiect on the flexural strength but little on the compressive itrength and fractule toughness. And also, considering the distributions of steel fiber, workablity and the maxinium size of coarse dqgregates, the optimum content of steel fiber seemed to be about 1.0 '0, and when lts length uias longer the results were somewhat tavorable.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.11
• /
• pp.927-936
• /
• 2014

This paper presents development and verification of the progressive failure analysis upon the composite laminates. Strength and stiffness of the fiber-reinforced composite are analyzed by property degradation approach with emphasis on the material nonlinearity and continuum damage mechanics (CDM). Longitudinal and transverse tensile modes derived from Hashin's failure criterion are used to predict the thresholds for damage initiation and growth. The modified Newton-Raphson iterative procedure is implemented for determining nonlinear elastic and viscoelastic constitutive relations. Laminar properties of the composite are obtained by experiments. Prediction on the un-notched tensile (UNT) specimen is performed under the laminate level. Stress-strain curves and strength results are compared with the experimental measurement. It is concluded that the present nonlinear CDM approach is capable of predicting the strength and stiffness more accurately than the corresponding linear CDM one does.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.317-328
• /
• 2010

The method to evaluate the flexural capacity of steel fiber-reinforced ultra high strength concrete beams was proposed in this study. An experimental program was set up and fourteen beams have been tested. Test results were compared with predictions by design code and by the proposed method, respectively. It was found that predictions by using ACI 544 Committee recommendations considerably underestimate the flexural capacity. Underestimation of flexural capacity resulted from that of tensile stress block. Three-point bending test data of notched prism specimens and their inverse analysis results were incorporated into modeling of tension stress block. The ratio of the predicted to the experimental flexural capacity was in the range of 0.98 to 1.14. The present study represents that the proposed method allows more realistic prediction of flexural capacity of steel fiber-reinforced ultra high strength concrete beams.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.2
• /
• pp.175-181
• /
• 2017

The purpose of this study is evaluating the characteristics of tensile strength of UHPC and examining tensile performance of notched specimens by direct tensile test. For test variables, 120, 150, and 180MPa of target design standard strength were aimed at. With general water curing and $90^{\circ}C$ high temperature steam as curing conditions, the properties were reviewed. Overall, it was represented that the specimens of notch-type direct tensile strength concrete was effective in inducing central cracks compared with existing direct tension specimens. Through this, it was judged that data construction with high reliability was possible. Above all, in a graph of direct tensile strength and strain, in the case of steam curing at high temperature, there was great difference of initial tensile strength compared with water curing. As passing of ages, an aspect that the difference gradually decreased was shown. Maximum tensile strength was found to increase steadily with increasing age for all target design strengths in water curing, in the case of steam curing, the tendency to increase significantly due to the initial strength development effect at 7 days of age. The initial crack strength increases with age in case of underwater curing, in the case of steam curing, it was higher than that of water curing in 7 days, while the strength of 28 days was lowered. In this part, it is considered necessary to examine the arrangement condition of the steel fiber.