• 비파괴검사학회지
• /
• 제36권4호
• /
• pp.288-294
• /
• 2016

Flexible ECT (eddy current array) probe를 사용하여 판재 및 용접부에 존재하는 notch 결함을 MS-5800E와 OmniScan MX 장비로 검출능력을 비교하고, 주파수와 lift-off를 변수로 신호의 특성을 비교하고자 하였다. 실험 결과, 500, 1000, 1500 kHz를 사용하였을 때 notch 깊이가 증가할수록 신호의 진폭이 증가하는 것으로 나타났고, lift-off 변화에 따른 신호의 진폭은 선형적으로 감소하였다. 또한 용접부 결함은 probe와 시험체의 접촉면에 밀접한 관계가 있다. Probe와 시험체의 접촉면이 양호한 경우 검출감도가 우수하고 그렇지 않은 경우에는 검출감도가 떨어지는 것을 알 수 있었다.

• 반도체디스플레이기술학회지
• /
• 제14권2호
• /
• pp.1-7
• /
• 2015

In this paper, a new capacitive pressure sensor has been proposed for a displacement measurement. The new sensor is mainly composed of a gap of $5{\mu}m$ and a notch of $1{\mu}m$. And the sensor has the performance as the high sensitivity and capacitance compared with a commercial capacitive sensor. Therefore, the advantages of the new capacitive pressure sensor are good sensitivity in normal range, mechanically robust and large overload protection. The analytical model is induced for confirming the performance of the proposed sensor. In addition, FEM (finite elements method) simulation has been performed to verify the analytical model. Firstly, the displacement characteristics of diaphragm membrane were simulated by the analytical model and FEM in the case of different structure and materials. At last, through this analysis, these simulation results can be predicted the change of the performance when the device parameters are varied. And it is used as a design tool to achieve at a set of performance we desired.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.929-940
• /
• 1995

The fatigue strength and fracture topography in the friction welded interface of high speed steel (HSS-Co) to SM55C carbon steel have been investigated through the fatigue test, SEM fractograph and EDS (energy dispersive spectrometer) analysis. Three kinds of specimens used in this research are the friction welded joints, HSS-Co and SM55C carbon steel with circumferential notch, saw notch and smooth, respectively. The notch sensitivity factor, .eta. of the friction welded joints is lower than that of the base materials, and that represents a superiority of the joint performance of FRW. Fracture topography of the FRW specimens with a notch showed a cleavage or brittle appearance, while that of the FRW smooth specimen appeared to be ductile. Furthermore, although fatigue crack likely initiated near the weld interface of the FRW smooth specimen, crack propagation continued into the HAZ of SM55C steel. Finally, fatigue fractures of the base materials were associated primarily with the inclusions located at the outer periphery of the specimen.

• 한국안전학회지
• /
• 제16권2호
• /
• pp.44-50
• /
• 2001

The rotated bending fatigue test was conducted in air md in 3.5% NaCl salt solution to investigate the fatigue fracture behaviour of raw material and F.E.M dual phase steel made from raw material(SS41) by a suitable heat treatment. This study has compared the initial microcrack creation of material by tensile test with that by fatigue test. And the rotated bending test of cantilever type under the condition of 3.5% NaCl salt solution and air has investigated the corrosion fatigue fracture behaviour with the variation of stress concentration factor determined by each of notch shapes. The initial microcrack have been developed in fragile grainboundary with general corrosion occurring in raw material : in the pits built up by corrosion in F.E.M. dual phase steel because pits bring out stress concentration. It is small that the degree of decrease in corrosion fatigue life for F.E.M. dual phase steel compared with raw material because the notch sensitivity of F.E.M. dual phase steel is lower than raw material in reason of characteristics with two-phase construction.

• 대한기계학회논문집
• /
• 제17권10호
• /
• pp.2475-2482
• /
• 1993

The effects of the hole size(2R) and the specimen width(W) on the fatigue strength and the fatigue life in plain woven glass/epoxy composite plates are experimentally investigated under constant amplitude tensile fatigue loading. It is shown in this study that the notch sensitivity under fatigue loading is lower than that under static loading. It can be explained by the fact that the stress concentration is relaxed by the damage developed at the boundary of circular hole. To predict the fatigue strength at a specific cycle, the modified point stress criterion represented as a function of the geometry of the specimen(2R and W) is applied. It is found that the model used in the prediction of the notched tensile strength predicts the fatigue strength with reasonable accuracy. A model for predicting the fatigue life in the notched specimen, based on the S-$N_f$, curve in the smooth specimen, is suggested.

• 전자공학회논문지
• /
• 제53권2호
• /
• pp.36-44
• /
• 2016

본 논문에서는 $0.18{\mu}m$ CMOS 공정을 이용하여 WBAN(Wireless Body Area Network)용 IR-UWB(Impulse Radio Ultra Wide Band) RF 송수신기를 제안한다. 설계된 송수신기는 3-5GHz UWB low band를 지원하며 OOK(On-Off Keying) 변조 방식을 사용한다. 수신기는 복잡도와 소모 전력을 줄이기 위해서 비동기식 에너지 검출 방식을 사용하였다. 원하지 않는 잡음을 제거하고 감도를 개선하기 위하여 RF active notch filter가 내장되어 있다. VCO 기반의 수신기는 switch mechanism을 사용하였다. 사용된 switch mechanism은 소모 전력을 줄이고 VCO leakage를 최소화 할 수 있다. 또한, 중심주파수가 변해도 항상 동일한 spectrum mask를 가진다. 측정된 수신기의 감도는 3.5 GHz의 중심주파수에서 1.579 Mbps의 전송 속도를 가질 때 -84.1 dBm을 가진다. 송신기와 수신기는 각각 0.3 nJ/bit, 41 mW의 소모 전력을 사용한다.

• 대한기계학회논문집
• /
• 제6권2호
• /
• pp.107-112
• /
• 1982

In order to analyze and investigate in the fatigue behavior of the notched specimens under the two level stressing, the U-notched specimens of structural carbon steel which is generally used is prepared. The obtained results are summarized as follows; (1) The fatigue limit of the U-notched specimens is lower than that of the unnotched. The fatifue notch factor (.betha.) of the U-notched specimens is 1.44 for mild steel and 1.52 for harden steel. The notch sensitivity (q) is 0.68 for mild steel and o.8 for harden steel. That is, these facts show that harden steel is more sensitive to the notch than mild steel. (2) The fatigue life time of the U-notched specimens under the overstressing is shorter than under the constant stressing, and the degree of fatigue life time decrease is different to each stress level; the degree for the high stress level is more than for the low stress level. (3) The fatigue life time of the U-notched specimes under the understressing is longer than under the constant stressing, and the degree of fatigue life time increase for the low stress level is more than for the high stress level.

• 한국정밀공학회지
• /
• 제21권3호
• /
• pp.147-154
• /
• 2004

This paper presents a procedure for analysis and design of a fine positioning stage, which has many applications in industries for machine tools, semiconductor, LCD and so forth. The stage considered here is based on a single module with 3 axes which is composed of flexures hinges, piezoelectric actuators and their peripherals. Through a series of analysis, the structural analysis model is simplified as a rigid body(the moving part) and springs(the flexures hinges). An experimental design procedure is applied to determine the dimension of flexures hinges. A sensitivity analysis on the notch positions is also performed to obtain a guideline of fabrication accuracy for the stage. An actual fine stage is made and verified through an experiment on the dynamic characteristics.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 Proceedings of the Korea Automatic Control Conference, 11th (KACC); Pohang, Korea; 24-26 Oct. 1996
• /
• pp.223-226
• /
• 1996

The moving vehicle with disturbances has the 6 dof motion in the pitching, yawing and rolling directions of two independent axes. The control system in such a moving vehicle has to perform disturbance rejection well. The paper presents PID controller with disturbance rejection function, low sensitivity filter and notch the bending frequency rejection. The performance of a designed system has been certified by the simulation and experiment results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 학술대회 논문집 전문대학교육위원
• /
• pp.129-131
• /
• 2000

The moving vehicle with disturbances has the 6 degree of freedom motion in the pitching, Yawing, and rolling directions of two independent axes. The control system in such a moving vehicle has to perform disturbance rejection. This paper present PID controller with disturbance rejection function, low sensitivity filter and notch filter for bending frequency rejection. The performance of a designed system has been certified by the simulation and experiment and experiment results.