• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.6
• /
• pp.773-778
• /
• 1997

The present study investigates the effect of the shear rate-dependent thermal conductivity of non-newtonian fluids on the heat transfer enhancement in a 2:1 rectangular duct flow. An axially-constant heat flux and a peripherally-constant temperature boundary conditions(H1) was adopted for a top-wall-heated configuration. The present numerical results of Nusselt numbers for SRDC(Separan) show heat transfer enhancement over those of SRIC. The Nusselt numbers increased linearly as Reynolds numbers increased. The heat transfer enhancement is due to an increased thermal conductivity near the wall, which is attributed to the shear rate-dependence.

• Journal of Magnetics
• /
• v.21 no.3
• /
• pp.468-475
• /
• 2016

In this article, entropy generation on MHD Williamson nanofluid over a porous shrinking sheet has been analyzed. Nonlinear thermal radiation and chemical reaction effects are also taken into account with the help of energy and concentration equation. The fluid is electrically conducting by an external applied magnetic field while the induced magnetic field is assumed to be negligible due to small magnetic Reynolds number. The governing equations are first converted into the dimensionless expression with the help of similarity transformation variables. The solution of the highly nonlinear coupled ordinary differential equation has been obtained with the combination of Successive linearization method (SLM) and Chebyshev spectral collocation method. Influence of all the emerging parameters on entropy profile, temperature profile and concentration profile are plotted and discussed. Nusselt number and Sherwood number are also computed and analyzed. It is observed that entropy profile increases for all the physical parameters. Moreover, it is found that when the fluid depicts non-Newtonian (Williamson fluid) behavior then it causes reduction in the velocity of fluid, however, non-Newtonian behavior enhances the temperature and nanoparticle concentration profile.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.385-388
• /
• 2008

The objective of this paper is simulating blood flow through the branched and stenotic tube numerically. SC-Tetra, which is one of the commercial code using FVM method, was utilized for this analysis. The flow is assumed as an incompressible laminar flow with the additional condition of non-Newtonian fluid. As the constitutive equation for the fluid viscosity, the following models were solved with governing equations ; Cross Model, Modified Cross Model, Carreau Model and Carreau-Yasuda Model. Final goal was achieved to get analytic data about shear stress, at specific points, changing the geometry with various factors like the bifurcation angle, diameter of the branches, the ratio of stenosis, and etc. The material property of blood was referred from the related papers. Furthermore, to verify results they were compared with those of the published papers. There were some discrepancies based on the different solver and the different data post-processing method. However, many parameters like the location of low shear stress, which arised from bifurcation or stenosis, and the tendency of various factors were found to be very similar.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.1
• /
• pp.9-16
• /
• 2014

This paper presents the theoretical analysis of a flow driven by surface tension and gravity in an inclined circular tube. A governing equation is developed for describing the displacement of a non-Newtonian fluid(Power-law model) that continuously flows into a circular tube owing to surface tension, which represents a second-order, nonlinear, non-homogeneous, and ordinary differential form. It was found that quantitatively, the theoretical predictions of the governing equation were in excellent agreement with the solutions of the equation for horizontal tubes and the past experimental data. In addition, the predictions compared very well with the results of the force balance equation for steady.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.177-180
• /
• 2008

The objective of this study is to get simulation data about pulsatile flow of a non-Newtonian fluid through a bifurcated tube. All the process was based on CFD method, with a commercial FVM code, SC/Tetra ver. 6.0 for solving, and with CATIA R16 for generating geometries. To define a non-Newtonian fluid, the following viscous models are used; the Powell-Eyring model, the modified Powell-Eyring model, the Cross model, the modified Cross model, the Carreau model, the Carreau-Yasuda model and the modified Power Law model. The flow calculation data using each model were compared with the other data of a existing paper. Finally, the Carreau model was recognized to give the best result with the SC/Tetra code, and the succeeding simulations are made with the model. For the pulsating flow condition, the sine wave type velocity profile is given as the inlet boundary condition. To investigate the effect of geometries and mesh, the pre-test is carried out with various curvature conditions of the bifurcated corner, and then with various mesh conditions. The final process is to calculate flow variables such as the wall shear stress (WSS) and the wall shear stress gradient (WSSG). To validate all the result, the simulation is compared with the existing data of the other papers. Generally speaking, there is a noticeable difference in the maximum and minimum value of WSS. It is not sure that the values in each data are on the exactly same location. However, the overall trend is similar. The next study needs to investigate the same situation by experimental method. Furthermore, if the flow is simulated with more pulsatile conditions, more data of flow field through a bifurcated tube could be achieved.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.1
• /
• pp.18-28
• /
• 2001

The present study investigates flow dynamics between two dimensional compliant plates under sinusoidal flow conditions in order to understand influence of wall motion, impedance phase angle (time delay between pressure and flow waveforms), and non-Newtonian fluid on wall shear stress using computational fluid dynamics. The results showed that wall motion induced additional terms in the streamwise velocity profile and the pressure gradient. These additional terms due to wall motion reduced the amplitude of wall shear stress and also changed the mean wall shear stress. The trend of the changes was very different depending on the impedance phase angle. As the impedance phase angle was changed to more negative values, the mean wall shear stress decreased while the amplitude of wall shear stress increased. As the phase angle was reduced from 0°to -90°under $\pm$4% wall motion, the mean wall shear stress decreased by 12% and the amplitude of wall shear stress increased by 9%. Therefore, for hypertensive patients who have large negative phase angles, the ratio of amplitude and mean of the wall shear stress is raised resulting in a more vulnerable state to atherosclerosis according to the low and oscillatory shear stress theory. We also found that non-Newtonian characteristics of the blood protect atherosclerosis by decreasing the oscillatory shear index.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.10a
• /
• pp.177-180
• /
• 2008

The objective of this study is to get simulation data about pulsatile flow of a non-Newtonian fluid through a bifurcated tube. All the process was based on CFD method, with a commercial FVM code, SC/Tetra ver. 6.0 for solving, and with CATIA R16 for generating geometries. To define a non-Newtonian fluid, the following viscous models are used; the Powell-Eyring model, the modified Powell-Eyring model, the Cross model, the modified Cross model, the Carreau model, the Carreau-Yasuda model and the modified Power Law model. The flow calculation data using each model were compared with the other data of a existing paper. Finally, the Carreau model was recognized to give the best result with the SC/Tetra code, and the succeeding simulations are made with the model. For the pulsating flow condition, the sine wave type velocity profile is given as the inlet boundary condition. To investigate the effect of geometries and mesh, the pre-test is carried out with various curvature conditions of the bifurcated corner, and then with various mesh conditions. The final process is to calculate flow variables such as the wall shear stress (WSS) and the wall shear stress gradient (WSSG). To validate all the result, the simulation is compared with the existing data of the other papers. Generally speaking, there is a noticeable difference in the maximum and minimum value of WSS. It is not sure that the values in each data are on the exactly same location. However, the overall trend is similar. The next study needs to investigate the same situation by experimental method. Furthermore, if the flow is simulated with more pulsatile conditions, more data of flow field through a bifurcated tube could be achieved.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.10
• /
• pp.1146-1152
• /
• 2011

Ink transfer process is very important to determine quality of printed pattern, therefore its mechanism should be understood to control printing quality. Although there have been many attempts to understand ink transfer mechanism by numerical simulation and experimental studies, their model was too much simple to model realistic printing process and our understanding is not enough yet. In this paper we designed ink transfer visualization system to present flow visualization of ink transfer process for gravure offset printing. We considered rotational effect of blanket roll which is related with printing speed and used non-Newtonian fluid as working fluid such as Ag paste. For printing unit, cantilever-type blanket roll is used for convenient visualization of ink transfer. Serial images were captured continuously by using high-speed CMOS camera and long range microscope. We investigated the effects of various design parameters such as printing speed and pattern angle on the ink transfer process. We found more stretched ink filament for non-Newtonian fluid than Newtonian fluid. As increasing printing speed, length of stretched ink filament and height of break-up point are also increased. We also compared ink transfer process between CD and MD pattern and its relationship with ink transfer mechanism.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.5
• /
• pp.584-595
• /
• 1998

An investigation was carried out to determine experimentally the thermal conductivities of non-Newtonian fluids in a shear field. Both time independent purely viscous and viscoelastic fluids were considered. A coaxial cylinder apparatus with a rotating outer cylinder was used to establish the velocity field in the test fluid. First, the thermal conductivity of distilled water measured to validate the instrument. The experimental water data agreed within 1% of literature values and there was no effect of outer cylinder rotation (shear field). However, for non-Newtonian fluids such as aqueous CMC and Separan solutions, there were significant increases in thermal conductivities of up to 70% for CMC and 50% for Separan depending on the shear rate, polymer concentration and temperature. Considering the shear rate dependent thermal conductivity in the study of heat transfer in non-Newtonian fluids could be important. As in natural convection, the momentum and energy equations could no longer be solved separately but would have to be solved simultaneously.

• Journal of computational fluids engineering
• /
• v.22 no.1
• /
• pp.95-102
• /
• 2017

Debris flow is a composition of solid objects of various sizes, suspension and water, which occurs frequently as the results of landslide following heavy rainfall. This often causes extensive damage in the form of socio-economic losses and casualties as witnessed during the incident around Mt. Umyeon, Seoul in 2011. There have been numerous investigation to mitigate the impacts from debris flow; however, the estimation as preparedness measure has not been successful due to nonlinear and multiphase characteristics of phenomena both in material and process inherent in the debris flow. This study presents a numerical approach to simulate the debris flow using open source code of computational fluid dynamics, OpenFOAM with non-Newtonian viscosity model for three phase material modeling. In order to validate the proposed numerical method, the quantitative evaluations were made by comparisons with experimental results and qualitative analysis for the dispersion characteristics was carried for the case of debris flow in the actual incident from Mt. Umyeon.