• Journal of the Korean institute of surface engineering
• /
• v.42 no.1
• /
• pp.21-25
• /
• 2009

Using an evaporation system, $SiO_2$ was deposited as a buffer layer between a PET substrate and a ITO layer and then ITO/$SiO_2$/PET layers were annealed for 1.5 hours at the temperature of $180^{\circ}C$. Adhesion and electro-optical properties of ITO films were studied with thickness variance of a $SiO_2$ buffer layer. As a result of introduction of the $SiO_2$ buffer layer, sheet resistance and resistivity increased and a ITO film with optimum sheet resistance ($529.3{\Omega}/square$) for an upper ITO film of resistive type touch panel could be obtained when $SiO_2$ of $50{\AA}$ was deposited. And it was found that ITO films with $SiO_2$ buffer layer have higher transmittance of $88{\sim}90%$ at 550 nm wavelength than ITO films with no buffer layers and the transmittance was enhanced as $SiO_2$ thickness increased from $50{\AA}$ to $100{\AA}$. Adhesion property of ITO films with $SiO_2$ buffer layers became better than ITO films with no buffer layers and this property was independent of $SiO_2$ thickness variance ($50{\sim}100{\AA}$). By depositing a $SiO_2$ buffer layer of $50{\AA}$ on the PET substrate and sputtering a ITO thin film on the layer, a ITO film with enhanced adhesion, electro-optical properties could be obtained.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.1
• /
• pp.24-28
• /
• 2012

In this study, we fabricated an amorphous InGaZnO pseudo-MOS transistor (a-IGZO ${\Psi}$-MOSFET) with a stacked $Si_3N_4/SiO_2$ (NO) gate dielectric and evaluated reliability of the devices with various thicknesses of a $SiO_2$ buffer layer. The roles of a $SiO_2$ buffer layer are improving the interface states and preventing degradation caused by the injection of photo-created holes because of a small valance band offset of amorphous IGZO and $Si_3N_4$. Meanwhile, excellent electrical properties were obtained for a device with 10-nm-thick $SiO_2$ buffer layer of a NO stacked dielectric. The threshold voltage shift of a device, however, was drastically increased because of its thin $SiO_2$ buffer layer which highlighted bias and light-induced hole trapping into the $Si_3N_4$ layer. As a results, the pseudo-MOS transistor with a 20-nm-thick $SiO_2$ buffer layer exhibited improved electrical characteristics and device reliability; field effective mobility(${\mu}_{FE}$) of 12.3 $cm^2/V{\cdot}s$, subthreshold slope (SS) of 148 mV/dec, trap density ($N_t$) of $4.52{\times}1011\;cm^{-2}$, negative bias illumination stress (NBIS) ${\Delta}V_{th}$ of 1.23 V, and negative bias temperature illumination stress (NBTIS) ${\Delta}V_{th}$ of 2.06 V.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.5
• /
• pp.439-444
• /
• 2005

We investigated the structural and electrical properties of BLT films grown on Si covered with $ZrO_{2}$ buffer layer. The BLT thin film and $ZrO_{2}$ buffer layer were fabricated using a metalorganic decomposition method. The electrical properties of the MFIS structure were investigated by varying thickness of the $ZrO_{2}$ layer. AES and TEM show no interdiffusion and reaction that suppressed using the $ZrO_{2}$ film as a buffer layer The width of the memory window in the C-V curves for the MFIS structure decreased with increasing thickness of the $ZrO_{2}$ layer. It is considered that the memory window width of MFIS is not affected by remanent polarization. Leakage current density decreased by about four orders of magnitude after using $ZrO_{2}$ buffer layer. The results show that the $ZrO_{2}$ buffer layers are prospective candidates for applications in MFIS-FET memory devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.574-577
• /
• 2001

GaN thin films on sapphire were grown by rf magnetron sputtering with ZnO buffer layer. The dependence of GaN film quality on ZnO buffer layer was investigated by X-ray diffraction(XRD). The improved film quality has been obtained by using thin ZnO buffer layer. Using Auger electron spectroscopy(AES), it was observed that the annealing process improved the GaN film quality. The surface roughness according to the annealing temperatures(700, 900, 1100$^{\circ}C$) were investigated by AFM(atomic force microscopy) and it was confirmed that the crystallization was improved by increasing the annealing temperature. Photoluminescence at 8K shows a near-band-edge peak at 3.2eV with no deep level emission.

• Journal of the Korean Vacuum Society
• /
• v.18 no.3
• /
• pp.213-220
• /
• 2009

The optimal condition of low temperature deposition of transparent conductive Al-doped zinc oxide (AZO) films is studied by RF magnetron sputtering method. To achieve enhanced-electrical property and good crystallites quality, we tried to deposit on glass using a two-step growth process. This process was to deposit AZO buffer layer with optimal growth condition on glass in-situ state. The AZO film grown at rf 120 W on buffer layer prepared at RF $50{\sim}60\;W$ shows the electrical resistivity $3.9{\times}10^{-4}{\Omega}cm$, Carrier concentration $1.22{\times}10^{21}/cm^3$, and mobility $9.9\;cm^2/Vs$ in these results, The crystallinity of AZO film on buffer layer was similar to that of AZO film on glass with no buffer later but the electrical properties of the AZO film were 30% improved than that of the AZO film with no buffer layer. Therefore, the cause of enhanced electrical properties was explained to be dependent on degree of crystallization and on buffer layer's compressive stress by variation of $Ar^+$ ion impinging energy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.148-151
• /
• 1995

Excimer laser has been used to fabricate superconducting YBa$_2$Cu$_3$O$\sub$7-x/(YBCO) thin films on various substrates. An XeCl excimer laser with an wavelength of 308 nm was used to deposit both buffer layer and superconducting thin film on sapphire substrate. The characterizations of the interface between thin film and substrate were performed. The interfacial properties of thin films on buffered sapphire and on bare sapphire were compared. With a 20 nm PrBa$_2$Cu$_3$O$\sub$7-x/(PBCO) buffer layer, no diffusion layer was observed between film and substrate while the diffusion layer with about 30 nm thickness was observed between film and sapphire without buffer layer.

• Applied Chemistry for Engineering
• /
• v.25 no.6
• /
• pp.577-580
• /
• 2014

Indium hydroxy sulfide ($In(OH)_xS_y$) as a cadmium (Cd)-free buffer layer for $CuInGaSe_2$ (CIGS) solar cells was prepared by the chemical bath deposition (CBD) and the reaction time was optimized. The band gap energy and transmittance data alongside the thickness results from the direct observation with focused ion beam system (FIB) could be a powerful tool for optimizing the conditions. In addition, X-ray diffractometer (XRD), X-ray photoelectron microscopy (XPS), and scanning electron microscope (SEM) were also employed for the layer characterization. The results indicated that the optimum reaction time for $In(OH)_xS_y$ buffer layer deposition by CBD was 20 min at $70^{\circ}C$ under the conditions employed. At the optimum conditions, the buffer layer thickness was near 57 nm and the band gap energy was 2.7 eV. In addition, it was found that there was no XPS peak shift in between the buffer layers deposited on molybdenum (Mo)/glass and that on CIGS layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.316-316
• /
• 2008

Using an evaporation method, $SiO_2$ was deposited as a buffer layer between a flexible PET substrate and a ITO film deposited by DC magnetron sputtering and electro-optical properties were investigated with thickness variance of $SiO_2$ layers. After coating a $SiO_2$ layer and a ITO film, the ITO/$SiO_2$/PET was heated up to $200^{\circ}C$ and the resistivity and the transmittance were measured by hall effect measurement system and UV/VIS/NIR spectroscopy. As a result of depositing a $SiO_2$ buffer layer, the resistivity increased and the transmittance and adhesion property were enhanced than ITO films with no buffer layers and the resistivity was lowered as $SiO_2$ thickness increased from 50 $\AA$ to 100 $\AA$. It was found that the transmittance was independent of annealing temperature variance in $150^{\circ}C{\sim}200^{\circ}C$ and the resistivity decreased as the temperature increased and especially decreasing rate of the resistivity was higher as the buffer layer thickness was thinner. So under optimized depositing of $SiO_2$ buffer layers and post-annealing of ITO/$SiO_2$/PET, ITO films with enhanced adhesion, electro-optical properties can obtained.

• Current Photovoltaic Research
• /
• v.3 no.2
• /
• pp.54-60
• /
• 2015

ZnSnO thin films were deposited by atomic layer deposition (ALD) process using diethyl zinc ($Zn(C_2H_5)_2$) and tetrakis (dimethylamino) tin ($Sn(C_2H_6N)_4$) as metal precursors and water vapor as a reactant. ALD process has several advantages over other deposition methods such as precise thickness control, good conformality, and good uniformity for large area. The composition of ZnSnO thin films was controlled by varying the ratio of ZnO and $SnO_2$ ALD cycles. The ALD ZnSnO film was an amorphous state. The band gap of ZnSnO thin films increased as the Sn content increased. The CIGS solar cell using ZnSnO buffer layer showed about 18% energy conversion efficiency. With such a high efficiency with the ALD ZnSnO buffer and no light soaking effect, AlD ZnSnO buffer mighty be a good candidate to replace Zn(S,O) buffer in CIGSsolar cells.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.6
• /
• pp.1069-1074
• /
• 2022

In this study, we prepared ITO thin films on the Nb₂O₅/SiO₂ double buffer layer and investigated electrical and optical properties according to the change of SiO₂ buffer layer thickness (40~50nm). The ITO thin film fabricated on the Nb₂O₅/SiO₂ double buffer layer exhibited a broad surface roughness with a small value ranging of 0.815 to 1.181nm, and the sheet resistance was 99.3 to 134.0Ω/sq. It seems that there is no problem in applying the ITO thin film to a capacitive touch screen panel. In particular, the average transmittance in the short-wavelength (400~500nm) region and the chromaticity (b^*) of the ITO thin film deposited on the Nb₂O₅(10nm)/SiO₂(40nm) double buffer layer showed significantly improved results as 83.58% and 0.05, respectively, compared to 74.46% and 4.28 of ITO thin film without double buffer layer. As a result, it was confirmed that optical properties such as transmittance in the short-wavelength region and chromaticity were remarkably improved due to the index matching effect in the ITO thin film with the Nb₂O₅/SiO₂ double buffer layer.