• 대한치과보철학회지
• /
• 제51권4호
• /
• pp.284-291
• /
• 2013

연구 목적: 상악 레진상 총의치의 정중 파절부에 금속선과 유리섬유 보강재를 사용하여 수리하였을 때 파절 강도 및 파절 양상을 비교해 보고자 하였다. 연구 재료 및 방법: 본 연구에서는 상악 의치의 정중부 파절을 재현한 뒤, 자가중합레진과 보강재를 사용하여 수리하였다. 보강재의 종류에 따라 3개의 군(대조군, 보강재 없음; W 군, 금속선; G 군, 섬유유리)으로 나누었으며, 각군당10개의 시편을 제작하였다. Instron test machine (Instron Co., Canton, MA, USA)으로 5.0 mm/min의 크로스헤드 속도를 부여하여 파절 강도를 구하였으며, 이때 하중은 20 mm의 지름을 가진 구형 하중체를 통해 의치 중심부에 전달되었다. 파절 강도 시험 후 나타난 의치의 파절 양상을 분석하였다. Kruskal-wallis test와 Mann-whitney U test를 이용하여 ${\alpha}=.05$ 수준에서 검정하였다. 결과: 파절 강도는W 군에서 가장 높은 값을 보였고, 대조군과 G 군 사이에서는 통계적으로 유의한 차이를 보이지 않았다(P>.05). 대조군과W군에서는 전후방파절 양상을 주로 보였고, G군에서는 보강재를 따라 파절되는 양상을 주로 보였다. 결론: 본 연구의 한계 내에서, 상악 총의치의 수리 시 유리섬유 보강재를 이용하는 경우 파절 강도가 향상되지 않았으며(P>.05), 유리섬유 보강재를 따라 접착 실패를 보이는 파절 양상이 나타났다.

• Design & Manufacturing
• /
• 제14권1호
• /
• pp.49-55
• /
• 2020

In this study, the fatigue behavior and fatigue life characteristics of PA2200 specimens fabricated by SLS 3D printer were studied. Fatigue tests were performed according to the standard specification (ASTM E468) and fatigue life curves were obtained. In order to perform the fatigue test, mechanical properties were measured according to the test speed of the simple tensile test, and the self-heating temperature of the specimen according to the test speed was measured using an infrared temperature measuring camera in consideration of heat generation due to plastic deformation. There was no significant difference within the set test speed range and the average self-heating temperature was measured at 38.5 ℃. The mechanical strength at the measured temperature showed a relatively small difference from the mechanical strength at room temperature. Fatigue test conditions were established through the preceding experiments, and the loading conditions below the tensile strength at room temperature 23 ℃ were set as the cyclic load. The maximum number of replicates was less than 100,000 cycles, and the fracture behavior of the specimens with the repeated loads showed the characteristics of Racheting. It was confirmed that SLS 3D printing PA2200 material could be applied to the Basquin's S-N diagram for the fatigue life curve of metal materials. SEM images of the fracture surface was obtained to analyze the relationship between the characteristics of the fracture surface and the number of repetitions until failure. Brittle fracture, crazing fracture, grain melting, and porous fracture surface were observed. It was shown that the larger the area of crazing damage, the longer the number of repetitions until fracture.

• 한국구조물진단유지관리공학회 논문집
• /
• 제16권6호
• /
• pp.155-162
• /
• 2012

해수에 노출된 콘크리트 구조물은 시간의 경과에 따라 철근부식이 야기될 수 있으며, 이는 구조적인 성능저하로 진전된다. 1단계 연구에서 도출된 해수전착시스템의 개발을 통하여 2단계 연구에서는 해수전착 코팅된 철근 및 코팅철근을 사용한 RC 콘크리트 부재의 구조적, 내구적 성능이 평가되었다. 내구적 성능평가에서는 반전위 측정이 수행되었는데, 코팅된 철근은 일반철근의 35%수준의 부식속도를 가지고 있었으므로 높은 내부식성을 확보하고 있었다. 구조실험에서는 직접인장시험, 부착력시험, RC 부재를 이용한 휨 및 전단시험이 수행되었다. 인장강도 시험에서는 3.2%, 부착성능에서는 8.8%의 강도 증가가 코팅된 철근에서 평가되었다. RC보에 대한 실험에서는 최대하중 및 파괴형태는 두가지 경우에서 거의 동일하게 평가되었다. 해수전착된 시편은 철근주위에 콘크리트와 비슷한 화합물(수산화마그네슘, 탄산칼슘)이 형성되므로 부착력 및 강도를 일부 증가시키는 것으로 평가되었다. 해수전착철근은 피로, 내충격성, 장기침지실험 등을 통하여 성능이 입증되면 더욱 활발하게 사용될 것으로 사료된다.

• The Journal of Advanced Prosthodontics
• /
• 제8권2호
• /
• pp.158-166
• /
• 2016

PURPOSE. The aim of this study was to determine the fracture resistance and the mode of fracture of endodontically treated teeth restored with different fiber posts and all-ceramic crowns. MATERIALS AND METHODS. Two glass fiber reinforced post systems in two different sizes and polyethylene fiber ribbon in two different thicknesses (n=10) were used. The specimens, restored with all-ceramic crowns, were subjected to a compressive load (in N) delivered at a 130-degree angle to the long axis until a fracture could be noted. The results were analyzed statistically with a One-Way ANOVA test (P<.05). RESULTS. Statistically significant differences were observed between the mean fracture resistance values of Postec, Snowlight, and Kerr Connect thin specimens (P<.0095). The Postec results (395.70 N) were found to be significantly higher than the others. No statistical difference was observed among the thick specimens (P<.2657). The mean fracture resistance values of the Snowlight thick samples were found to be higher than those of the Snowlight thin samples. The specimens were always fractured around the cemento-enamel junction at the palatinal side. No post fracture was observed for the thin Snowlight and Kerr Connect specimens or for the thick Postec and Kerr Connect specimens. Among the common failure types of the specimens, the worst was observed to be the root fracture failure. The highest post dislodgement failure result (80%) was obtained from the thin Kerr Connect specimen. CONCLUSION. In terms of optimizing fracture resistance, the fiber post size selection should be done according to the forces applied to the restored teeth.

• The Journal of Advanced Prosthodontics
• /
• 제8권6호
• /
• pp.489-493
• /
• 2016

PURPOSE. This in-vitro study aimed to evaluate the fracture resistances and failure modes of endodontically treated mandibular premolars restored with endocrowns and conventional post-core retained crowns. MATERIALS AND METHODS. Thirty mandibular premolars were assigned into three groups (n=10): GI, intact teeth; GE, teeth with endocrowns; GC, teeth with conventional post-core supported crowns. Except for the teeth in group GI, all specimens were cut to 1.5 mm above the cementoenamel junction and endodontically treated. Both endocrowns and conventional crowns were fabricated from lithium-disilicate blocks using a CEREC 3D CAD/CAM unit. All specimens were subjected to thermocycling and then to $45^{\circ}$ oblique compressive load until fracture occurred. The fracture resistance and failure mode of each specimen were recorded. Data were analyzed with one-way ANOVA and LSD Post Hoc Test (${\alpha}=.05$). RESULTS. The fracture resistances of GE and GC were significantly lower than that of GI (P<.01), while no significant difference was found between GE and GC (P=.702). As of the failure mode, most of the specimens in GE and GC were unfavorable while a higher occurrence of favorable failure mode was presented in GI. CONCLUSION. For the restoration of mandibular premolar, endocrown shows no advantage in fracture resistance when compared with the conventional method. Both of the two methods cannot rehabilitate endodontically treated teeth with the same fracture resistances that intact mandibular premolars have.

• 대한통합의학회지
• /
• 제7권1호
• /
• pp.81-88
• /
• 2019

Purpose : The purpose of this study was to examine if there is any correlation between pelvic tilt angle and trunk motion and trunk extensor during trunk forward flexion and to measure trunk motion, onset time of trunk motion, and onset time of trunk extensor activation. Methods : The subjects of this study were 42 healthy adults. The subjects had no back pain due to neurological disease and no experience of back surgery. After pelvic tilt angle was measured, each trunk forward flexion was performed three times. Trunk motion and onset time of trunk motion were measured using Myomotion. Four sensors were used, with one located at the upper thoracic (below $C_7$), the lower thoracic ($T_{12}-L_1$), the sacrum ($S_1$), and at the center of the anterior femur. Onset time of trunk extensors (spinalis, longissimus, gluteus medius, gluteus maximus, biceps femoris, and gastrocnemius) activation was measured using a wireless surface EMG. The EMG amplitude was normalized by using the reference voluntary contraction (RVC). The statistical significance of the results were evaluated using Pearson's correlation test. Results : The correlation between pelvic tilt angle and lumbar motion, onset time of pelvis motion, and onset time of gluteus medius activation was statistically significant in a positive direction (p<.05). The correlation between pelvic tilt angle with pelvis motion, onset time of lumbar motion, and onset time of longissimus activation showed a statistically significant negative correlation (p<.05). Conclusion : The study results provide a significant contribution to our understanding of the lumbar load at the initial stage of trunk flexion. Therefore, it may be possible to provide basic data for evaluation and treatment, such as orthodontic treatment for alignment of the spine and back pain. In addition, it is necessary to focus on normal exercise pattern reeducation as well as pelvic correction during exercise in daily life or in industrial fields.

• 셀메드
• /
• 제11권4호
• /
• pp.18.1-18.8
• /
• 2021

Jawarishe Jalinoos (JJ) is an orally used formulation available in semisolid dosage form, prepared with powdered plant materials mixed in honey or sugar syrup. It has many admirable pharmacological effects and used in Unani medicine to treat various acute and chronic disorders since ancient times. The ICH Harmonised Tripartite Guideline stated that photostability testing should be an essential part of stability testing to confirm that light exposure does not result in an unacceptable change in drugs substance and finished products. To date, the effect of light on JJ is not studied, in this study photostability evaluation of JJ was carried out. The test sample was manufactured with genuine ingredients in the in-door pharmacy of the National Institute of Unani Medicine. JJ was packed in two transparent polyethylene terephthalate airtight containers. The first sample was analysed at zero-day and the second sample was placed in a stability chamber subjected to light challenge with an overall illumination of 1.2 million lux hours combined with near ultraviolet energy of 200-watt hours per square meter by using option 2, along with 30±2℃ temperature and relative humidity 70±5%. Analysis of both finished products showed no considerable changes in organoleptic characters. Less than 5% variation was observed in physicochemical parameters. HPTLC fingerprinting showed justifiable variation. Microbial load and specific counts were within the limit prescribed by WHO. As no unacceptable changes were noted in JJ subjecting to light challenge, it is concluded that JJ is a photostable Unani compound formulation.

• 설비공학논문집
• /
• 제7권2호
• /
• pp.249-265
• /
• 1995

The performance of a refrigerant mixture of propane(R290)/isobutane(R600a) as a substitute for CFC12 was investigated in a domestic refrigerator with single evaporator. A thermodynamic cycle simulation indicated an increase in COP of a 1.7 to 2.4% with R-290/600a in the composition range of 0.2 to 0.6 mass fraction of R290 compared to CFC12. For the tests, two units($299{\ell}$, $465{\ell}$) were used. All refrigeration components remained the same throughout the tests, except that the length of capillary tube and amount of charge were changed for the mixture. The refrigerators were fully instrumented with more than 20 thermocouples, 2 pressure transducers, and watt/watt-hour meter for each refrigerator. 'Energy consumption test' and 'no load pulldown test' were performed under the same condition. The experimental results obtained with the same compressor indicated that R-290/600a mixture at 0.6 mass fraction of R290 showed a 3 to 5% increase in energy efficiency and a faster cooling speed compared to CFC12. The R-290/600a mixture showed a shorter compressor on-time and a lower compressor dome temperature than CFC12. In conclusion, the proposed hydrocarbon mixture seems to be an appropriate candidate to replace CFC12 without causing more environmental problems.

• 한국건설순환자원학회논문집
• /
• 제6권1호
• /
• pp.66-71
• /
• 2018

일반적으로 소구경 말뚝을 이용한 기존교각의 확대보강을 시행하는 경우 접합부의 일체성을 유지하기 위해 후 설치 앵커 중에서 이형철근을 사용한 부착식 앵커를 사용한다. 그러나 부착식 앵커의 경우 접합재의 종류 등에 따라 성능이 크게 좌우됨에도 불구하고 기계식 앵커와는 달리 설계방법의 표준화와 함께 적절한 성능평가를 위한 표준적인 실험방법도 제시되지 않고 있는 실정이다. 이에 따라 본 연구에서는 철근의 겹이음 및 앵커철근을 이용한 모형실험을 실시하여 부착식 앵커의 성능에 대한 평가를 수행하였다. 실험 결과, 접합하지 않은 시험체의 구조 성능이 가장 우수하게 나타났으며, 파괴양상은 펀칭전단 파괴로 나타났다. 연결되지 않은 부재가 연결된 부재보다는 부재 끝단의 처짐이 더 작게 발생되며, 큰 크기로 연결된 부재의 처짐이 작게 연결된 부재의 처짐보다는 크게 나타나, 하중이 증가할수록 앵커 철근 또는 겹이음 철근의 미끌림 등의 현상이 발생될 가능성이 큰 것으로 나타났다.

• 대한치과보철학회지
• /
• 제43권6호
• /
• pp.717-726
• /
• 2005

Statement of problem. One of the common problems of provisional crown and fixed partial denture materials is that when they are subjected to constant loads for a long period of time, they exhibit a dimensional change (creep). Purpose. The aim of this study was to investigate the viscoelastic behaviour of polymer-based provisional crown and fixed partial denture materials with time at constant compressive load. Material and methods. Three dimethacrylate-based materials (Protemp 3 Garant, Temphase, Luxatemp) and one monomethacrylate-based material (Trim) were selected. Dimensional changes of the specimens were recorded by a LVDT to evaluate their viscoelastic behavior and creep strain. For all specimens, two loading procedures were used. At first, static compressive stress of 4 MPa was applied for 30 minutes and followed by 1 hour of strain recovery. Then, after 24 hours of water storage, the specimens were loaded again. The creep values between materials were statistically analyzed using one-way ANOVA and multiple comparison $Scheff\acute{e}$ test. Independent samples t-test was also used to identify the difference of creep strain between first and secondary loading conditions at the significance level of 0.05. Results. Following application of the first loading, Trim showed the highest maximum creep strain (32.7%) followed by Luxatemp, Protemp 3 Garant and Temphase, with values of 3.78%, 2.86% and 1.77%, respectively. Trim was significantly different from other materials (P<0.05), while there were no significant differences among Luxatemp, Protemp 3 Garant and Temphase (P>0.05). The highest recovery and permanent set of Trim, were significantly different from those of others (P<0.05). At the secondary loading of the dimethacrylate-based materials, creep deformation, recovery and permanent set decreased and the percentage of recovery increased, while in Trim, all values of the measurements increased. This result showed that the secondary loading at 24 hours produced a significant creep magnitude. Conclusion. The dimethacrylate-based provisional crown and fixed partial denture materials showed significantly higher creep resistance and lower deformation than the monomethacrylate-based material. Thus, monomethacrylate-based materials should not be used in long-term stress-bearing situations.