• Transactions on Electrical and Electronic Materials
• /
• v.12 no.5
• /
• pp.200-203
• /
• 2011

In this research, nitrogen (N)-doped zinc oxide (ZnO) thin films have been grown on a sapphire substrate by dielectric barrier discharge (DBD) in pulsed laser deposition (PLD). DBD has been used as an effective way for massive in-situ generation of N-plasma under conventional PLD process conditions. Low-temperature photoluminescence spectra of N-doped ZnO thin films provided near-band-edge emission after a thermal annealing process. The emission peak was resolved by Gaussian fitting and showed a dominant acceptor-bound excitation peak ($A^{\circ}X$) that indicated acceptor doping of ZnO with N. The acceptor binding energy of the N acceptor was estimated to be approximately 145 MeV based on the results of temperature-dependent photoluminescence (PL) measurements.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.406-409
• /
• 2012

Recently, enormous research efforts have been focused on the development of non-precious catalysts to replace Pt for electrocatalytic oxygen reduction reaction (ORR), and to reduce the cost of proton exchange membrane fuel cells (PEMFCs). In recent years, heteroatom (N, B, and P) doped carbon nanostructures have been received enormous importance as a non-precious electrode materials for oxygen reduction. Doping of foreign atom into carbon is able to modify electronic properties of carbon materials. In this study, nitrogen and boron doped carbon nanostructures were synthesized by using a facile and cost-effective thermal annealing route and prepared nanostructures were used as a non-precious electrocatalysts for the ORR in alkaline electrolyte. The nitrogen doped carbon nanocapsules (NCNCs) exhibited higher activity than that of a commercial Pt/C catalyst, excellent stability and resistance to methanol oxidation. The boron-doped carbon nanostructure (BC) prepared at $900^{\circ}C$ showed higher ORR activity than BCs prepared lower temperature (800, $700^{\circ}C$). The heteroatom doped carbon nanomaterials could be promising candidates as a metal-free catalysts for ORR in the PEMFCs.

• Korean Journal of Materials Research
• /
• v.24 no.10
• /
• pp.556-564
• /
• 2014

To synthesize a high-performance photocatalyst, N doped $TiO_2$ nanotubes deposited with Ag nanoparticles were synthesized, and surface characteristics, electrochemical behaviors, and photocatalytic activity were investigated. The $TiO_2$ nanotubular photocatalyst was fabricated by anodization; the Ag nanoparticles on the $TiO_2$ nanotubes were synthesized by a reduction reaction in $AgNO_3$ solution under UV irradiation. The XPS results of the N doped $TiO_2$ nanotubes showed that the incorporated nitrogen ions were located in interstitial sites of the $TiO_2$ crystal structure. The N doped titania nanotubes exhibited a high dye degradation rate, which is effectively attributable to the increase of visible light absorption due to interstitial nitrogen ions in the crystalline $TiO_2$ structure. Moreover, the precipitated Ag particles on the titania nanotubes led to a decrease in the rate of electron-hole recombination; the photocurrent of this electrode was higher than that of the pure titania electrode. From electrochemical and dye degradation results, the photocurrent and photocatalytic efficiency were found to have been significantly affected by N doping and the deposition of Ag particles.

• Journal of Powder Materials
• /
• v.16 no.3
• /
• pp.196-202
• /
• 2009

A visible-light photoactive $TiO_{2-x}N_x$ photocatalyst was synthesized successfully by means of cogrinding of anatase-$TiO_2(a-TiO_2)$ in $NH_3$ ambient, followed by heat-treatment at $200^{\circ}C$ in air environment. In general, it is well known that the grinding-operation induces phase transformation of a-$TiO_2$ to rutile $TiO_2$. This study investigates the influence of the amount of $NH_3$ gas on the phase transformation rate of a-$TiO_2$ and enhancement of visible-light photocatalytic activity, and also examines the relation between the photocatalytic activity and the period of grinding time. The phase transformation rate of a-$TiO_2$ to rutile is retarded with the amount of NH3 injected. And the visible-light photocatalytic activity of samples, was more closely related to the period of grinding time than $NH_3$ amount injected, which means that the doping amount of nitrogen into $TiO_2$ more effective to mechanical energy than $NH_3$ amount injected. XRD, XPS, FT-IR, UV-vis, Specific surface area (SSA), NOx decomposition techniques are employed to verify above results more clearly.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.71-72
• /
• 1998

반도체 집적 공정의 발달로 차세대 소자용으로 30 A 이하의 극 박막 Si02 절연막이 요구되고 있으며, 현재 제품으로 50-70 A 두께의 절연막을 사용한 것이 발표되고 있다. 절연막의 두께가 앓아질수록 많은 문제가 발생할 수 있는데 그 예로 절연막의 breakdo때둥에 의한 신뢰성 특성의 악화, 절연막올 통한 direct tunneling leakage current, boron풍의 dopant 침투로 인한 소자 특성 ( (Threshold Voltage)의 불안, 전기적 stress하에서의 leakage current증가와 c charge-trap 및 피terface s쩌.te의 생성으로 인한 소자 특성의 변화 둥으로 요약 된다. 절연막의 특성올 개선하기 위해 여러 가지 새로운 공정들이 제안되었다. 그 예로, Nitrogen올 Si/Si02 계면에 doping하여 절연막의 특성을 개선하는 방법 으로 고온 열처 리 를 NH3, N20, NO 분위 기 에서 실시 하거 나, polysilicon 또는 s silicon 기판에 nitrogen올 이온 주입하여 열처리 하는 방법, 그리고 Plasma분 위기에서 Nitrogen 함유 Gas를 이용하여 nitrogen을 doping시키는 방법 둥이 연구되고 있다. 또한 Oxide cleaning 후 상온에서 성장되는 oxide를 최소화 하여 절연막의 특성올 개선하기 위하여 LOAD-LOCK을 이용하는 방법, C뼈피ng 공정의 개선올 통한 contamination 감소와 silicon surface roughness 감소 로 oxide 신뢰성올 개선하는 방법 둥이 있다. 구조적 인 측면 에 서 는 Polysilicon 의 g없n size 를 최 적 화하여 OxideIPolysilicon 의 계면 특성올 개선하는 연구와 Isolation및 Gate ETCH공정이 절연막의 특성에 미 치 는 영 향도 많이 연구되 고 있다 .. Plasma damage 가 Oxide 에 미 치 는 효과 를 제어하는 방법과 Deuterium열처리 퉁올 이용하여 Hot electron Stress하에서 의 MOS 소자의 Si/Si02 계면의 신뢰성을 개선하고 있다. 또한 극 박막 전연막의 신뢰성 특성올 통계적 분석올 통하여 사용 가능한 수명 올 예 측 하는 방법 과 Direct Tunneling Leakage current 를 고려 한 허 용 가농 한 동작 전 압 예측 및 Stress Induced Leakage Current 둥에 관해서 도 최 근 활발 한 연구가 진행되고 있다.

• Journal of IKEEE
• /
• v.18 no.2
• /
• pp.214-219
• /
• 2014

In this paper, the usage of tilt-implanted trench Schottky diode(TITSD) based on silicon carbide is proposed. A tilt-implanted trench termination technique modified for SiC is proposed as a method to keep all the potentials confined in the trench insulator when reverse blocking mode is operated. With the side wall doping concentration of $1{\times}10^{19}cm^{-3}$ nitrogen, the termination area of the TITSD is reduced without any sacrifice in breakdown voltage while potential is confined within insulator. When the trench depth is set to 11um and the width is optimized, a breakdown voltage of 2750V is obtained and termination area is 38.7% smaller than that of other devices which use guard rings for the same breakdown voltage. A Sentaurus device simulator is used to analyze the characteristics of the TITSD. The performance of the TITSD is compared to the conventional trench Schottky diode.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.2
• /
• pp.68-73
• /
• 2015

Single crystals of $Yb^{3+}$ doped $Y_3Al_5O_{12}$ up to 25 at.% were grown by the Czochralski method. Using the pulling rate of 0.8 mm/h and the rotation rate of 10 rpm, single crystals with diameters of up to 40 mm and lengths up to 160 mm were obtained. The growth atmosphere was either pure nitrogen or the mixture of nitrogen and oxygen. The crystal was bluish green when using pure nitrogen and the crystal was colorless when using the mixture of 99 % nitrogen and 1 % oxygen. The concentration of $Yb^{3+}$ ions decreased with increasing the length of the crystal and $Yb^{3+}$ concentration of core area was slightly higher than the other areas in the compositional analysis. The fluorescence lifetime decreased with increasing the doping concentration of $Yb^{3+}$ ions.

• Journal of Pharmaceutical Investigation
• /
• v.22 no.3
• /
• pp.197-204
• /
• 1992

A gas chromatographic method using nitrogen phosphorous selective detection was developed for simultaneous determination of haloperidol and its metabolite, reduced haloperidol, in human plasma. Combelen was used as internal standard, The method involved extraction and trimethylsilylation followed by the injection of $2-4\;{\mu}l$ of benzene layer, which was used to dissolve the trimethylsilylated derivatives of haloperidol and reduced haloperidol, onto SE-54 column [5% phenyl methyl silica fused capillary column, $16m{\times}0.22\;mm$ $(I.D.){\times}0.33\;{\mu}m$ (coated thickness)]. The temperature of column oven was programmed from $200^{\circ}C\;to\;300^{\circ}C$ at the increase rate of $10^{\circ}C/min and also the temperatures of injector and detector were set at $300^{\circ}C$. Helium was used as carrier gas and its flow rate was maintained at 30 ml/min. The detection was conducted with nitrogen phosphorous selective detector. The retention times for combelen, reduced haloperidol and haloperidol were found to be 9.14, 9.75 and 9.99 min, respectively. The detection limits for haloperidol and reduced haloperidol in human plasma were both 0.2 ng/ml. The coefficients of variation of the intra-assay were generally low (below 9.8%). The mean absolute recoveries of added haloperidol and reduced haloperidol from plasma were 72% and 84%, respectively. No interferences from endogenous substances were found.

• Korean Journal of Materials Research
• /
• v.31 no.9
• /
• pp.502-510
• /
• 2021

Hierarchically porous carbon materials with high nitrogen functionalities are extensively studied as high-performance supercapacitor electrode materials. In this study, nitrogen-doped porous carbon textile (N-PCT) with hierarchical pore structures is prepared as an electrode material for supercapacitors from a waste cotton T-shirt (WCT). Porous carbon textile (PCT) is first prepared from WCT by two-step heat treatment of stabilization and carbonization. The PCT is then nitrogen-doped with urea at various concentrations. The obtained N-PCT is found to have multi-modal pore structures with a high specific surface area of 1,299 m² g^-1 and large total pore volume of 1.01 cm³ g^-1. The N-PCT-based electrode shows excellent electrochemical performance in a 3-electrode system, such as a specific capacitance of 235 F g^-1 at 1 A g^-1, excellent cycling stability of 100 % at 5 A g^-1 after 1,000 cycles, and a power density of 2,500 W kg^-1 at an energy density of 3.593 Wh kg^-1. Thus, the prepared N-PCT can be used as an electrode material for supercapacitors.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.10 no.3
• /
• pp.1-9
• /
• 1973

Gallium phosphide light emitting diode (LED) has been fabricated first time for pilot lamp and numeric display purposes. Bright red light is obtained in forward bias at very low current of one to five mA. A typical p-n junction is formed by liquid phase epitaxial growth on a n-type gallium physphide substrate. The crystal growth is achieved at about 1300$^{\circ}$K after the equilibrium of the gallium solution followed by tipping operation. The ohmic contact is made by wire bonding by thermal compression technique. The entire process is well fit for laboratory scale to fabricate a few hundred diodes for mainly demonstration purpose. For mass production, a large sum of the capital investment is required. The great merit of gallium phosphide LED is at low current operation, and green light emission is also obtainable by nitrogen doping.