• Journal of Korean Society on Water Environment
• /
• v.22 no.1
• /
• pp.116-121
• /
• 2006

Fundamental investigations have been carried out to find the applicability of manganese nodule as an adsorbent of nickel ion with an intention that nickel can be secured in manganese nodule along with the treatment of wastewater. The average content of manganese in nodules which used in the experiments was about 27%. The content of nickel in manganese nodules was observed to increase up to 4 times higher with comparison to its original value after adsorption. When the initial concentration of nickel ion in artificial wastewater was lower than 500 mg/L, its adsorbed amount on manganese nodule was shown to increase continuously. However, no more than about 82 mg/L of nickel was attained at higher initial nickel ion concentration than 500 mg/L. The adsorption of nickel ion was increased with temperature under experimental conditions and as the size of manganese nodule particles became smaller more nickel ion was adsorbed on adsorbent. Regarding the effect of pH, the adsorption of nickel ion was more hindered as the solution became acidic. Adsorption behavior of nickel ion on manganese nodule was found to follow the Freundlich model well and kinetic analysis showed that the adsorption reaction of nickel ion was second order. Thermodynamic parameters for the nickel ion adsorption were estimated on the basis of thermodynamic equations and they were in good agreement with experimental results.

• Journal of Korean Society on Water Environment
• /
• v.21 no.1
• /
• pp.14-20
• /
• 2005

A feasibility study has been conducted regarding the application of waste coffee grounds as an adsorbent for the treatment of nickel ion containing wastewater. The major variables which considered to influence the adsorbability of nickel ion were its initial concentration, reaction temperature, pH, and coexisting ion. The specific surface area of coffee grounds used in the experiment was found to be ca. $39.67m^2/g$, which suggesting its potential applicability as an adsorbent due to its relatively high surface area. In the experimental conditions, more than 90% of the initial amount of nickel ion was shown to adsorb within 15 minutes and equilibrium in adsorption was attained after 3 hours. The adsorption behavior of nickel ion was well explained by Freundlich model and kinetics study showed that the adsorption reaction was second-order. Adsorption was reduced with temperature and its change of enthalpy in standard state was estimated to be -807.05 kJ/mol. Arrhenius equation was employed for the calculation of the activation energy of adsorption and nickel ion was observed to adsorb on coffee grounds exoentropically based on thermodynamic estimations. As pH rose, the adsorption of nickel ion was diminished presumably due to the formation of cuboidal complex with hydroxide ion and the coexistence of cadmium ion was found to decrease the amount of nickel ion adsorption, which was proportional to the concentration of cadmium ion.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.1 s.256
• /
• pp.50-54
• /
• 2007

Nickel nano and microstructures are fabricated with simple process. The fabrication process consists of nickel deposition, lithography, nickel ion etching and plasma ashing. Well-aligned nickel nanowalls and nickel self-encapsulated microchannels were fabricated. We found that the ion etching condition as a key fabrication process of nickel nanowalls and self-encapsulated microchannels, i.e., 40 sccm Ar flow, 550 W RF power, 15 mTorr working pressure, and $20^{\circ}C$ water cooled platen without using He backside cooling unit and with using it, respectively. We present the experimental results and discuss the formational conditions and the effect of nickel redeposition on the fabrication of nickel nano and microstructures.

• Resources Recycling
• /
• v.17 no.1
• /
• pp.59-65
• /
• 2008

The adsorption features of nickel ion in wastewater on manganese dioxide from spent batteries were investigated for its usage as an adsorbent. The aquatic behavior of nickel ion was characterized by MINTEQ program and the considered influential variables on the adsorption of nickel ion were its initial concentration, reaction temperature, the amount of adsorbent, and pH. The adsorption ratio of nickel ion decreased with increasing its initial concentration and thermodynamic estimation has been carried out based on the adsorption characteristics of nickel ion depending on temperature. In addition, the adsorption of nickel ion was shown to be promoted according to the amount of manganese dioxide and a lot of nickel ions were adsorbed as the solution pH was raised.

• Polymer(Korea)
• /
• v.27 no.1
• /
• pp.61-68
• /
• 2003

In this study, we have investigated the preparation of mixed bead and fiber type hybrid ion-exchanger for recovering nickel ion from plating rinse water. There was little dependence of adsorption capacity for nickel ion on the mixing ratio of resin type and fiber type of ion exchangers. However, it increased with increasing the resin content in the mixed bed. It was shown that the data Langmuir and Freundlich's adsorption isotherm model were well fitted to the linear. Affinity between the functional groups in the ion exchanger and nickel ion in the process was confirmed. The pressure drop decreased with increasing the number of stage in the multistage bed, but it increased with increasing the resin content in the mixing bed. The initial breakthrough time in the multistage bed was short due to the increase of number of stage in the continuous process. It was found that the final breakthrough time of the multistage bed was little changed. The breakthrough time decreased with increasing the amount of fibrous ion exchanger in the mixed bed. The maximum adsorption capacities of the mixed and multistage beds were 2.51 meq/g and 2.69 meq/g, respectively. The desorption time for the nickel ion with $1N H_2SO_4$ solution was lower than 10 minutes and the yield of desorption was greater than 98 percent.

• Journal of the Korean Society of Industry Convergence
• /
• v.19 no.4
• /
• pp.198-205
• /
• 2016

For the study on the ion exchange of nickel hexacyanoferrate(NiHCNFe) electrode with the several cations, the film of hexacyanoferrate was prepared on the bare nickel surface by the electrochemical and chemical methods in the solution composed with 5mM K3Fe(CN)6 and 100mM KNO3. To compare the capability of the ion exchange of NiHCNFe film electrode, the repeated cyclic voltammograms were measured in the 0.5M cation nitrate solutions at $25^{\circ}C$ and pH7. It was found that the capacity of the electrochemically derivatized NiHCNFe reduced in the rate of 0.5~0.7%/cycle and was nearly exhausted at the 150th potential cycle. Better result was obtained from that the capacity loss of the chemically assembled NiHCNFe was less than 0.02%/cycle for 5,000cycles. Furthermore, the residual capacity was more than 30% at the 5,000th cycle.

• Journal of the Korean Chemical Society
• /
• v.32 no.6
• /
• pp.536-542
• /
• 1988

A nickel(Ⅱ) complex, Ni(IAA-NBz) (IAA-NBz') with ligand, N-benzylisonitrosoacetyl acetone imine (H-IAA-NBz) has been synthesized. This complex is very stable at room temperature and has cis-form and trans-form isomers. The ratio of nickel (Ⅱ) ion and ligand combined is 1 : 2. The elemental analysis, ir, nmr. electronic spectra and mass spectra have been studied. It is suggested from these studies that the isonitroso group of one ligand, H-IAA-NBz coordinates to nickel(Ⅱ)ion through the nitrogen atom to form five-membered ring, while that of the other ligand, H-IAA-NBz coordinates to nickel (Ⅱ) ion through the oxygen atom to form six-membered ring in square-planar complex.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.613-617
• /
• 2010

Ferro-Nickel slag is one of the by-products in Ferro-Nickel manufacturing process. The slag is composed of $SiO_2$, MgO, $Fe_2O_3$ and others. But the slag has been buried at landfill despite having valuable elements. This study tried to extract Mg ion and fabricate Mg compound from ferro-nickel slag using hydrochloric acid solution. Mg ion was extracted with Si, Fe and other ions in HCl solution. So reprocess was needed for gaining high purity Mg ion. It was thought that Si ion or $SiO_2$ precipitated in HCl solution and removed from solution in filtering process. Fe ion converted into $Fe(OH)_3$ after reacted with $NH_4OH$ and precipitated in HCl solution. After these process, the filtrate was composed of high purity Mg ion. $MgCl_2{\cdot}NH_4Cl{\cdot}6H_2O$ was obtained through drying of filtrate and this product was changed into MgO by burning process ($600^{\circ}C$-30 min). That is, 1st material or solution for manufacturing 2nd product was fabricated using acid dissolution method and other treatments.

• Polymer(Korea)
• /
• v.25 no.6
• /
• pp.789-795
• /
• 2001

In order to recover nickel ion from waste water containing heavy metals, the PAN fibrous ion-exchanger with primary, secondary amine groups and carboxyl group was synthesized by acid and base hydrolysis. The hydrolysis yield of PAN fiber in acid solution was higher than base solution. The swelling ratio and ion-exchange capacity of PAN fiber which was synthesized in 1N $H_2SO_4$ solution at $80^{\circ}C$ for 7 hrs appeared 71.2% and 1.95 meq/g respectively. We investigated that the adsorption of nickel ion was approached 1.44 meq/g at 50 min and the maximum adsorption capacity of ion-exchanger was 2.48 meq/g. We confirmed that the $Ni^{+2}$ adsorption ability of the synthesized PAN fibrous ion-exchanger in this study is excellent.

• Korean Journal of Materials Research
• /
• v.20 no.11
• /
• pp.592-599
• /
• 2010

A porous nickel-tin nano-dendritic electrode, for use as the anode in a rechargeable lithium battery, has been prepared by using an electrochemical deposition process. The adjustment of the complexing agent content in the deposition bath enabled the nickel-tin alloys to have specific stoichiometries while the amount of acid, as a dynamic template for micro-porous structure, was limited to a certain amount to prevent its undesirable side reaction with the complexing agent. The ratios of nickel to tin in the electro-deposits were nearly identical to the ratios of nickel ion to tin ion in the deposition bath; the particle changed from spherical to dendritic shape according to the tin content in the deposits. The nickel to tin ratio and the dendritic structure were quite uniform throughout the thickness of the deposits. The resulting nickel-tin alloy was reversibly lithiated and delithiated as an anode in rechargeable lithium battery. Furthermore, the resulting anode showed much more stable cycling performance up to 50 cycles, as compared to that resulting from dense electro-deposit with the same atomic composition and from tin electrodeposit with a similar porous structure. From the results, it is expected that highly-porous nickel-tin alloys presented in this work could provide a promising option for the high performance anode materials for rechargeable lithium batteries.