• Journal of Environmental Science International
• /
• v.28 no.1
• /
• pp.65-73
• /
• 2019

The catalytic activity of Ni-0.2%YSZ (Yttria-Stabilized Zirconia) with different promoters was evaluated for $CO_2$ methanation. The catalysts were weighed for mixing and they were dried at $110^{\circ}C$ for molding into disks. The concentration of $CO_2$ and $CH_4$ for conducting of $CO_2$ methanation were analyzed by gas chromatography and the physical characteristics of the disk-type catalyst formed were analyzed by X-ray diffraction, scanning electron microscope and energy dispersive x-ray spectrometer. The addition of $CeO_2$ as a promoter for Ni-0.2%YSZ (denoted as Ni-5%Ce-0.2%YSZ) resulted in the highest $CO_2$ methanation. It also showed catalytic activity at a low temperature($200^{\circ}C$). Following this, $ZrO_2$, $SiO_2$, $Al_2O_3$ and $TiO_2$ were added to Ni-5%Ce-0.2%YSZ to compare the $CO_2$ methanation, and the highest efficiency was found for. Ni-1%Ti-5%Ce-0.2%YSZ Then, the concentration of Ti was increased to 10% and the catalytic activity was estimated using seven different types of commercial $TiO_2$. In conclusion, ST-01 $TiO_2$ showed the highest efficiency for $CO_2$ methanation.

• Applied Chemistry for Engineering
• /
• v.35 no.2
• /
• pp.134-139
• /
• 2024

In the steam reforming of methane reactions, the effect of adding noble metals Ru and Pd to a Ni-based catalyst as promoters was analyzed in terms of catalytic activity and hydrogen production. The synthesized catalysts were coated on the surface of a honeycomb-structured metal monolith to perform steam methane reforming reactions. The catalysts were characterized by XRD, TPR, and SEM, and after the reforming reaction, the gas composition was analyzed by GC to measure methane conversion, hydrogen yield, and CO selectivity. The addition of 0.5 wt% Ru improved the reduction properties of the Ni catalyst and exhibited enhanced catalytic activity with a methane conversion of 99.91%. In addition, reaction characteristics were analyzed according to various process conditions. Methane conversion of over 90% and hydrogen yield of more than 3.3 were achieved at a reaction temperature of 800 ℃, a gas hourly space velocity (GHSV) of less than 10000 h^-1, and a ratio of H₂O to CH₄ (S/C) higher than 3.

• Clean Technology
• /
• v.13 no.4
• /
• pp.287-292
• /
• 2007

[ $M/Al_2O_3$ ] (M = Mn, Fe, Co, Ni, Cu) catalysts supported on commercial alumina ($Al_2O_3$) were prepared by an impregnation method, and were applied to the hydrogen production by auto-thermal reforming of ethanol. It was revealed that each catalyst retained its own metallic phase and product distribution strongly depended on the identity of active metal. Among the catalysts prepared, $Ni/Al_2O_3$ and $Co/Al_2O_3$ showed the best catalytic performance in the auto-thermal reforming of ethanol. However, the reaction mechanisms over these two catalysts were different. Ni/Al_2O_3 catalyst showed 100% ethanol conversion at $500^{\circ}C$, but it exhibited a rapid decrease in hydrogen selectivity. Although $Co/Al_2O_3$ catalyst showed an excellent performance in hydrogen selectivity, on the other hand, no significant improvement in hydrogen yield was observed due to the low ethanol conversion over the catalyst.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.466-470
• /
• 2008

The objective of this study is to convert methane into hydrogen using a nanoporous catalyst in the $CO_2$ containing syngas generated from the gasified waste. For the purpose, $Ni/Al_2O_3$ catalyst was prepared with the one-pot method. According to analyses of the catalyst, three dimensionally linked sponge shaped particles were created and the prepared nanoporous catalysts had larger surface area and smaller particle size and more uniform pores compared to the sphere shaped commercial catalyst. The catalyst for reforming reaction gave the highest $CH_4$ conversion of 91%, and $CO_2$ conversion of 92% when impregnated with 16 wt% of Ni at the reaction temperature of $750^{\circ}C$. At that time, the prepared catalyst remarkably improved the $CH_4$ and $CO_2$ conversion up to 20% compared to the commercial one.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.12
• /
• pp.1297-1298
• /
• 2001

• Journal of Korean Society for Atmospheric Environment
• /
• v.6 no.1
• /
• pp.57-72
• /
• 1990

The oxidation of carbon monoxide on a catalyst, $LaSrNiCoO_3$ was investigatigated with a plug flow system. Kinetic quantities such as reaction-rate, reaction order and Arhenius-parameters at various reactor temperature from 200$^\circ$C to 300$^\circ$C were determined. Also, the optimum condition for the oxidation of carbon monoxide with this catalyst was determined and are as follows. Partial pressure of oxigen ; 428mmHg Partial pressure of carbon monoxide ; 332mmHg Mixed moral ratio of oxigen and Carbon monoxide ; 1.3 : 1 Total gas flow ; 224ml/min Reaction temperature ; 340$^\circ$C The reaction kinetic equation at the optimum condition, temperature range from 200$^\circ$C to 340$^\circ$C, are as follow. $$ $v = Ae^{6.5Kcal/RT} [CO]^{0.93 \sim 0.98} [O_2]^{0.42 \sim 0.50}$ $$ In addition to this, numerical calculation were performed to evaluate the mass and heat transfer effect on this system.

• Korean Chemical Engineering Research
• /
• v.47 no.1
• /
• pp.17-23
• /
• 2009

The catalytic behavior of $Ni/Ce_XZr_{(1-X)}O_2$ loaded on the alumina coated honeycomb monolith was studied for the autothermal reforming reaction of methane. Among the catalysts with the different Ce/Zr ratios, the $Ni/Ce_{0.80}Zr_{0.20}O_2$ Catalyst showed the highest conversion of methane. By investigating the effect of Ni content on the $Ni/Ce_{0.80}Zr_{0.20}O_2$ catalysts, the catalyst loaded with 15wt% Ni had the highest activity. Also, $H_2$ yield was increased as $H_2O/CH_4$ ratio increased. Methane conversion was improved as $O_2/CH_4$ ratio was increased, whereas the yield of $H_2$ was decreased. Among the catalysts tested for 30 hours, $Ni(15wt%)/Ce_{0.80}Zr_{0.20}O_2$ showed the excellent conversion(${\geq}99%$) of methane and the stability at the condition of $GHSV=30,000h^{-1}$, feed ratio S/C/O=2/1/0.5 and reaction temperature $800^{\circ}C$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.2
• /
• pp.166-173
• /
• 2006

Catalytic reforming of $CO_2$ by $CH_4$ over Ni-YSZ based catalysts was investigated to produce syngas as raw material of high valued chemicals and develop high performance catalyst electrode for an internal reforming of $CO_2$ in SOFC system. Ni-YSZ based catalysts were prepared using physical mixing and maleic acid methods to improve catalytic activity and inhibition of carbon deposition. The catalysts before and after the reaction were characterized by $N_2$ physisorption, TPR(temperature programed reduction), XRD and impedance analyzer. The conversions for $CO_2$ and $CH_4$ over Ni-MgO catalyst showed 90% but much amount of carbon deposition was detected on catalyst surface. On the other hand, the conversions for $CO_2$ and $CH_4$ over NiO-YSZ-$CeO_2$ catalyst showed 100% and 85% respectively, and carbon deposition on catalyst surface was inhibited under the tested condition. It was concluded that NiO-YSZ-$CeO_2$ catalyst is a promising candidate for the catalytic reforming of $CO_2$ and the internal reforming in SOFC system.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.8
• /
• pp.1265-1272
• /
• 2007

A solid acid catalyst, NiSO4/CeO2-ZrO2 was prepared simply by promoting ZrO2 with CeO2 and supporting nickel sulfate on CeO2-ZrO2. The support of NiSO4 on ZrO2 shifted the phase transition of ZrO2 from amorphous to tetragonal to higher temperatures because of the interaction between NiSO4 and ZrO2. The surface area of 10-NiSO4/1-CeO2-ZrO2 promoted with CeO2 and calcined at 600 oC was very high (83 m2/g) compared to that of unpromoted 10-NiSO4/ZrO2 (45 m2/g). This high surface area of 10-NiSO4/1-CeO2-ZrO2 was due to the promoting effect of CeO2 which makes zirconia a stable tetragonal phase as confirmed by XRD. The role of CeO2 was to form a thermally stable solid solution with zirconia and consequently to give high surface area and acidity of the sample, and high thermal stability of the surface sulfate species. 10-NiSO4/1- CeO2-ZrO2 containing 1 mol% CeO2 and 10 wt% NiSO4, and calcined at 600 oC exhibited maximum catalytic activities for both reactions, 2-propanol dehydration and cumene dealkylation.

• Transactions of the Korean hydrogen and new energy society
• /
• v.35 no.1
• /
• pp.27-33
• /
• 2024

In this study, we researched Ni-based bead catalysts for the catalytic thermal decomposition of light hydrocarbons. A Ni-based bead-type catalyst was prepared, and catalytic thermal decomposition performance of light hydrocarbons was evaluated. The 30Ni/Al₂O₃ catalyst exhibited the most superior performance, with the presence of both fibrous and carbon black forms on the catalyst surface. Catalytic performance was evaluated for particles sized between 150-250 and 500 ㎛, with excellent catalytic thermal decomposition properties in the 150-250 ㎛ range. After the reaction, carbon removal through collision between catalysts in the fluidized bed was observed. It was confirmed that as the particle size increases, the amount of carbon removed increases.