• 대한화학회지
• /
• 제53권3호
• /
• pp.233-243
• /
• 2009

실리카지지 니켈(Ni-Si$O_2$), 실리카지지 구리(Cu-Si$O_2$), 몇가지 조성의 실리카지지 니켈과 구리의 합금(Ni/Cu-Si$O_2$)을 실온에서 일산화탄소(CO)의 압력을 넓은 범위에서 변화시키면서(0.2 $torr{\sim}$50 torr) 흡착된 CO의 적외선 스펙트럼을 1500 $cm^{-1}{\sim}2500\;cm^{-1}$ 범위에서 관찰했고 실온에서 진공탈착시키면서 흡착된 CO의 적외선 스펙트럼을 관찰했다. Ni-Si$O_2$에 CO를 흡착시켰을 때 2059.6 $cm^{-1},\;{\sim}$2036.5 $cm^{-1},\;{\sim}$1868.7 $cm^{-1},\;{\sim}$1697.1 $cm^{-1}$의 네 흡수띠가 관찰되었고, Cu-Si$O_2$에 일산화탄소를 흡착시켰을 때 $\sim$2115.5 $cm^{-1},\;{\sim}$1743.0 $cm^{-1}$ 두 흡수띠가 관찰되었으며, Ni/Cu-Si$O_2$에서는 ${\sim}2123.2\;cm^{-1}$, 2059.6 $cm^{-1},\;{\sim}$2036.4 $cm^{-1},\;{\sim}$1899.5 $cm^{-1},\;{\sim}$1697.1 $cm^{-1}$에 다섯 흡수띠가 관찰되었다. Ni/Cu-Si$O_2$, Cu-Si$O_2$, Ni/Cu-Si$O_2$에서 CO를 흡착시켰을 때 관찰된 흡수스펙트럼은 이전의 보고와 근사적으로 일치한다. 1800 $cm^{-1}$ 이하의 흡수띠는 Ni이나 Ni/Cu 합금의 스텦이 있는 결정표면에서 관찰된 바 있는데 Ni-Si$O_2$, Ni/Cu-Si$O_2$를 실온에서 CO를 흡착시켰을 때 나타나는 ${\sim}1697.1\;cm^{-1}$ 흡수띠는 Ni이나 Ni/Cu 합금 표면에서 스텦에 인접한 흡착자리에 흡착한 CO에 기인한 흡수띠로 제시할 수 있다. Cu-Si$O_2$ 시료를 실온에서 CO를 흡착시켰을 때 Cu 결정표면에서 2000 $cm^{-1}$ 이하의 흡수띠가 관찰되는 경우는 드문데 1743.0 $cm^{-1}$ 흡수띠는 Cu 표면의 스텦에 인접한 흡착자리에 흡착한 CO에 기인한 흡수띠로 제시할 수 있다. Ni/Cu-Si$O_2$에서 Cu의 함량이 몰분율 0.5까지 변함에 따라 같은 CO 압력 또는 같은 진공탈착시간에서 흡수띠의 위치가 21 $cm^{-1}$ 이하로 다른 ⅠB 금속을 첨가했을 때보다 작게 변하는데 Cu d 전자의 리간드 효과가 작은 현상에 기인한 것으로 볼 수 있다.

• 한국표면공학회지
• /
• 제24권2호
• /
• pp.103-113
• /
• 1991

Electroless Ni-Cu-P alloy plating of Al base hard disk was performed to investigate some properties according to the change of composition. It was found that the composition of Ni and Cu in deposits changed linearly with increasing the mole ratio of NiSO4.6H2O/CuSO4.5H2O. The increase in hardness by heat - treatment was confirmed to be associated with small size grained crystallization of the amorphous deposits. Acid resistance of all deposits layer. which had been heated up to 30$0^{\circ}C$, was found to be exellent when immersed in 1N-H2SO4 solution, and it showed more superior acid resistance with decreasing Cu content and with increasing P. The resistivity of the deposits heat treated became smaller at temperature more than 50$0^{\circ}C$, and it became largerly with increasing P content. Cu 44.1wt% alloy(C bath) showed the most superior non-magnetically stable characteristics after heat treatment. It was superiorly with higher temperature and with decreasing P content.

• 한국분말재료학회지
• /
• 제22권5호
• /
• pp.362-366
• /
• 2015

The effect of sublimable vehicle composition in the camphor-naphthalene system on the pore structure of porous Cu-Ni alloy is investigated. The CuO-NiO mixed slurries with hypoeutectic, eutectic and hypereutectic compositions are frozen into a mold at $-25^{\circ}C$. Pores are generated by sublimation of the vehicles at room temperature. After hydrogen reduction at $300^{\circ}C$ and sintering at $850^{\circ}C$ for 1 h, the green body of CuO-NiO is completely converted to porous Cu-Ni alloy with various pore structures. The sintered samples show large pores which are aligned parallel to the sublimable vehicle growth direction. The pore size and porosity decrease with increase in powder content due to the degree of powder rearrangement in slurry. In the hypoeutectic composition slurry, small pores with dendritic morphology are observed in the sintered Cu-Ni, whereas the specimen of hypereutectic composition shows pore structure of plate shape. The change of pore structure is explained by growth behavior of primary camphor and naphthalene crystals during solidification of camphor-naphthalene alloys.

• 한국표면공학회지
• /
• 제42권5호
• /
• pp.232-239
• /
• 2009

This study presented the effect of membrane thickness on hydrogen permeability. Microvoids on the surface of the membrane should not exist for the exact values of hydrogen permeability. Pd-Cu-Ni hydrogen alloy membranes were fabricated by Ni powder sintering, substrate plasma pretreatment, sputtering and Cu reflow process. And this leaded to void-free surface and dense film of Pd-Cu-Ni hydrogen alloy membrane. Hydrogen permeation test showed that hydrogen permeability increased from 2.7 to $15.2ml/cm^2{\cdot}min{\cdot}atm^{0.5}$ as membrane thickness decreased from 12 to $4{\mu}m$. This represented the similar trend as a hydrogen permeability of pure palladium membrane based on solution-diffusion mechanism.

• 마이크로전자및패키징학회지
• /
• 제17권1호
• /
• pp.1-7
• /
• 2010

본 연구에서는 $430^{\circ}C$에서 Bi-10Cu-20Sb-0.3Ni 조성의 솔더 합금과 Cu간의 리플로루 솔더링 시 생성되는 계면 반응층을 분석하였고, 솔더링 시간에 따른 계면 반응층의 성장 속도를 측정하였다. 리플로우 솔더링 후 Bi-10Cu-20Sb-0.3Ni/Cu의 계면 반응층을 분석한 결과, $(Cu,Ni)_2Sb$ 및 $Cu_4Sb$ 금속간 화합물층, 그리고 Bi 조성과 $Cu_4Sb$ 상이 주기적으로 존재하는 아지랑이 형상층이 연속적으로 생성되었다. 또한 120 s까지의 솔더링 시간 영역에서는 계면 반응층의 총 두께가 솔더링 시간에 대해 직선적으로 증가하는 경향이 관찰되었다. 합금원소로 첨가된 Ni은 가장 두꺼운 $Cu_4Sb$ 반응층의 형성에 참여하지 않아 계면 금속간 화합물의 성장 속도를 억제시키는 작용을 나타내지 못했다.

• 열처리공학회지
• /
• 제26권5호
• /
• pp.225-232
• /
• 2013

The influence of aging treatment, addition elements and rolling reduction ratio on the microstructure, mechanical, electrical and bendability properties of Cu-Ni-Si-P-x (x = Fe, Sn, Zn) alloys for connector material application was investigated. SEM/EDS analysis exhibited that Ni2-Si precipitates with a size of 20~100 nm were distributed in grains. Fe, Sn, Zn elemnets in Cu-Ni-Si-P alloy imporved the mechanical strength but it was not favor in increasing of electrical conductivity. As higher final rolling reduction ratio, the strength and electrical conductivity is increased after aging treatment, but it indicated excellent bendability. Especially, Cu-2Ni-0.4Si-0.5Sn-0.1Fe-0.03P alloy show the tensile strength value of 700MPa and the electrical conductivity was observed to reach a maximum of 40%IACS. It is optimal for lead frame and connector.

• 한국분말재료학회지
• /
• 제27권1호
• /
• pp.1-7
• /
• 2020

In this research, a new medium-entropy alloy with an equiatomic composition of FeCuNi was designed using a phase diagram (CALPHAD) technique. The FeCuNi MEA was produced from pure iron, copper, and nickel powders through mechanical alloying. The alloy powders were consolidated via a high-pressure torsion process to obtain a rigid bulk specimen. Subsequently, annealing treatment at different conditions was conducted on the four turn HPT-processed specimen. The microstructural analysis indicates that an ultrafine-grained microstructure is achieved after post-HPT annealing, and microstructural evolutions at various stages of processing were consistent with the thermodynamic calculations. The results indicate that the post-HPT-annealed microstructure consists of a dual-phase structure with two FCC phases: one rich in Cu and the other rich in Fe and Ni. The kernel average misorientation value decreases with the increase in the annealing time and temperature, indicating the recovery of HPT-induced dislocations.

• 한국전기전자재료학회논문지
• /
• 제14권4호
• /
• pp.328-335
• /
• 2001

In this work, we made the precision thin film resistors of NiCr alloy (74wt%Ni-f18wt%Cr-4wt%Al-4wt%Cu) using DC/RF magnetron sputtering method and studied the sheet resistance and TCR(Temperature Coefficient of Resistance) etc... of the Ni-Cr-Al-Cu alloy thin film according to the change by annealing treatment to 400$\^{C}$ in air and nitrogen atmosphere and the change(power, pressure, substrate temperature) of sputtering process.

• The Journal of Advanced Prosthodontics
• /
• 제6권3호
• /
• pp.215-223
• /
• 2014

PURPOSE. This study aimed to develop a copper-aluminium-nickel alloy which has properties comparable to that of dental alloys used for dental post and core applications with the reasonable cost. MATERIALS AND METHODS. Sixteen groups of experimental copper alloys with variants of 3, 6, 9, 12 wt% Al and 0, 2, 4, 6 wt% Ni were prepared and casted. Their properties were tested and evaluated. The data of thermal, physical, and mechanical properties were analyzed using the two-way ANOVA and Tukey's test (${\alpha}$=0.05). The alloy toxicity was evaluated according to the ISO standard. RESULTS. The solidus and liquidus points of experimental alloys ranged from $1023^{\circ}C$ to $1113^{\circ}C$ and increased as the nickel content increased. The highest ultimate tensile strength ($595.9{\pm}14.2$ MPa) was shown in the Cu-12Al-4Ni alloy. The tensile strength was increased as the both elements increased. Alloys with 3-6 wt% Al exhibited a small amount of 0.2% proof strength. Accordingly, the Cu-9Al-2Ni and Cu-9Al-4Ni alloys not only demonstrated an appropriate modulus of elasticity ($113.9{\pm}8.0$ and $122.8{\pm}11.3$ GPa, respectively), but also had a value of 0.2% proof strength ($190.8{\pm}4.8$ and $198.2{\pm}3.4$ MPa, respectively), which complied with the ISO standard requirement (>180 MPa). Alloys with the highest contents of nickel (6 wt% Ni) revealed a widespread decolourisation zone (5.0-5.9 mm), which correspondingly produced the largest cell response, equating positive control. CONCLUSION. The copper alloys fused with 9 wt% Al and 2-4 wt% Ni can be considered for a potential use as dental post and core applications.

• 한국분말재료학회지
• /
• 제1권2호
• /
• pp.145-152
• /
• 1994

Atomizing mode and powder characteristics of CuA1Ni base shape memory alloy in rotating disk atomization were investigated in accordance with disk materials and additional elements. Produced powders were classified into two types of spherical and flake shape. In the case of CuAlNiBTi and CuAlNiZr alloy, high yield rate and fine powder were obtained. This tendency was same when we used oxide coated disks. We concluded that this results were steno from the wetting characteristics change between molten metal and disk surface. Especially, due to the reactive properties of Ti and Zr with ceramic disk, the change of atomizing appearance and powder characteristics were noticeable.