• Korean Journal of Materials Research
• /
• v.10 no.10
• /
• pp.715-720
• /
• 2000

By the mechanical alloying method. Ni-WC composite materials were prepared to improve the deformation-resistance for creep and sintering of Ni-anode at the operating temperature of $650^{\circ}C$. Mechanically alloyed powder w was initially fabricated by ball milling for 80hr, and then amorphization was occurred by the destruction of ordered crystals based on XRD analysis. In order to investigate the electrochemical performance and sheet characteristics of Ni-WC anode, tape casting process was adopted. Finally, the obtained sheet thickness of Ni- we after sintering at $1180^{\circ}C$ for 60 minutes in $H_2$ atmosphere was O.9mm and the average pore size was $3~5{\mu\textrm{m}}$ with porosities of 55%. The second phase was not observed in Ni- W matrix while W particles were finely and uniformly distributed in Ni matrix. This fine and uniform distributed W particles in Ni matrix are expected to enhance the mechanical properties of Ni anode through the dispersion and solid solution hardening mechanisms.

• Progress in Superconductivity
• /
• v.2 no.1
• /
• pp.33-38
• /
• 2000

Ni tapes were textured by taking advantage of their secondary recrystallization. The obtained 18cm long tapes had textures of single crystalline qualities with their [001] axes tilted with respect to the surface and their [010] axes parallel to the rolling direction. The reproducibility of this texturing was checked by taking statistics on the crystal orientations of 24 Ni tapes. $YBCO/CeO_2/YSZ/CeO_2$ films grown on the Ni tape had the same crystalline orientations. Magnetic field dependent I-V relations were measured on a 5cm section of the tape. $J_c$ defined by $20{\mu}V/mm$ criterion was $1.5\times10^5A/cm^2$ at 77K under zero field and was reduced by $\sim$50% under the applied magnetic field of 5T.

• Progress in Superconductivity
• /
• v.6 no.1
• /
• pp.69-73
• /
• 2004

Ni alloy tape is electropolished to be used as a metal substrate for fabrication of IBAD (ion-Beam Assisted Deposition)-MgO texture template fur HTS coated conductor. Electropolishing is needed to obtain a very smooth surface of Ni alloy tape because the in-plane texture of templates is sensitive to the roughness of metal substrate. The critical current of YBCO coated conductor depends on the texture of YBCO that depends on the texture of the IBAD MgO layer. And so the smoothness of the metal substrate is directly related to the superconducting properties of the coated conductor. In this study, we have prepared a reel-to-reel electropolishing apparatus to polish the Ni alloy tapes for IBAD. Various electropolishing conditions were investigated to improve the surface roughness. Hastelloy tape is continuously electropolished with high polishing current density (0.5 ∼ 2 A/$\textrm{cm}^2$) and fast processing time (1 ∼ 3 min). Polished hastelloy tapes have surface roughness(RMS) of below 1 nm on a 5 ${\times}$ 5 $\mu\m^2$ from AFM and SEM.

• Progress in Superconductivity and Cryogenics
• /
• v.4 no.2
• /
• pp.16-20
• /
• 2002

Bi-axially textured Ni tapes for YBCO coated conductors were Prepared by cold rolling and heat treatment of Ni Powder compacts. The Ni powder used in this study was 5 urn in particle size and 99.99 % in purity. The process of this study consists of filling of hi powder into a rubber mold, cold-isostatically Pressing and sintering of the powder compacts at 110$0^{\circ}C$ for 6h in 96 % Ar - 4 % H$_2$ atmosphere. The sintered compacts were cold rolled with a 5 % step reduction ratio into a 100 micron-thick tapes and then heat-treated at 100$0^{\circ}C$ for various time periods. The (200) texture of Ni tape was successfully developed through the recrystallization heat treatment of the cold rolled Ni tapes. At 100$0^{\circ}C$, the degree of texture of the heat-treated Ni tapes seems not to be significantly affected by the heat-treatment time. The short heat treatment of S min was sufficient to develop the complete (200) cube texture. The degree of in-Plane and out-of-plane texture of the prepared Ni tapes was 8-10$^{\circ}$. The heat treated Ni tapes consisted of equiaxed grains with a size 50-70 microns. and the AFM sol-face roughness was as smooth as 3 nm.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1993.05a
• /
• pp.87-89
• /
• 1993

용융탄산염 연료전지 양극 재료인 tape casting된 다공성 Ni-Cr 합금과 Ni-Al 합금의 전기화학적 특성과 소결 및 creep특성이 양극조건의 분위기 $650^{\circ}C$에서 조사되었다. 이들 전극재료의 전류밀도는 100 mV의 과전압에서 약 100~150㎃/$\textrm{cm}^2$의 크기이었다. Ni-Al 합금에서는 Ni 표면에 형성된 $Al_2$O$_3$의 영향으로 소결저항성이 큰 것으로 나타났으며, Creep 특성도 Al 첨가량의 증가에 의해 향상되었다.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.86-91
• /
• 2000

Ni tapes were textured by taking advantage of their secondary recrystallization. The obtained 18cm long tapes had textures of single crystalline qualities with their [001] axes tilted with respect to the surface and their [010] axes parallel to the rolling direction. YBCO/CeO$_2$/YSZ/CeO$_2$ films grown on the Ni tape had the same crystalline orientations. Magnetic field dependent I-V relations were measured on a 5cm section of the tape. Jc defined by 1mV criterion was 1.5 ${\times}$ 10$^5$A/cm$^2$ at 77K under zero field and was reduced by ${\sim}$50% under the applied magnetic field of 5T.

• 한국초전도학회:학술대회논문집
• /
• v.13
• /
• pp.32-32
• /
• 2003

• 한국초전도학회:학술대회논문집
• /
• 2007.07a
• /
• pp.62-62
• /
• 2007

• Journal of Powder Materials
• /
• v.10 no.4
• /
• pp.241-248
• /
• 2003

Biaxially textured Ni tapes were fabricated by a cold working and recrystallization heat treatment processes from powder compact rods. The processing parameters associated with the cube texture formation in Ni tapes were systematically investigated by using X-ray diffraction and pole-figure analysis. The Ni powder used in this study was 5 $\mu$m in size and 99.99% in purity. To find the optimum sintering temperature, tensile tests were performed for Ni rods sintered at various temperatures. The Ni rods sintered at 100$0^{\circ}C$ showed poor elongation and low fracture strength, while the Wi rods sintered above 100$0^{\circ}C$ revealed good mechanical properties. The higher elongation and fracture strength of the Ni rods sintered at higher temperatures than 100$0^{\circ}C$ are attributed to the full densification of the sintered rods. The sintered Ni rods were cold-rolled with 5% reduction to the final thickness of 100 $\mu$m and then annealed for development of rube texture in rolled Ni tapes. The annealed Ni tapes depicted strong cube texture with FWHM(full-width at half-maximum) of in-plane and out-of-plane in the range of 8$^{\circ}$ to 10$^{\circ}$. The NiO deposited on the Ni tapes by MOCVD process showed good epitaxy with FWHM=10$^{\circ}$, which indicates that the Ni tapes can be used as a substrate for YBCO coated conductors.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.3
• /
• pp.9-12
• /
• 2006

Batch type co-evaporation EDDC (Evaporation using Drum in Dual Chambers) system was recently manufactured to fabricate 100m - long SmBCO superconducting coated conductor. As a preliminary study before the fabrication of long tape. short CC samples have been fabricated using the EDDC system and their crystal texture and $I_c$ properties were investigated. $1.2 {\mu}m$-thick SmBCO layers were deposited on $CeO_2/YSZ/CeO_2$ buffered Ni-W tapes. $I_c$ of 128A/cm-w and corresponding $J_c$ of $1.1 MA/cm^2$ at 77K in self-field were obtained for SmBCO CC tape. In-field property of SmBCO CC was confirmed to be better than that of YBCO deposited by PLD.