• Progress in Superconductivity
• /
• 제3권1호
• /
• pp.111-114
• /
• 2001

Short-length and long-length Ni tapes were fabricated by powder processing, cold rolling and recrystallizatioon heat treatment. In the case of the short-length Ni tape, both in-plane and out-of-plane texture were less than $10^{\circ}$. In the case of the long-length Ni tape, the degree of texture is lower than that of the short-length Ni tape. The relationship between the texture formation and the processing parameter is reported.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권4호
• /
• pp.240-245
• /
• 2000

The self-field losses in a long multifilamentary Bi-2223/AgMgNi tape with varying transport current, voltage tap configurations, frequency and tape arrangements were investigated. Experimental results show that the measured losses are strongly dependent on voltage gap configurations but independent on tape arrangements. All voltage taps except the center tap are found to agree well with those predicted by Norris for an elliptical conductor. The self-field losses are purely hysteretic in nature in the range of applied frequencies for the transport currents below the critical current.

• Progress in Superconductivity
• /
• 제1권2호
• /
• pp.120-124
• /
• 2000

Ni-13%Cr and Ni-70%Cu alloy tapes were prepared by using high purity metal powders as starting materials. The Ni-13%Cr and the Ni-70%Cu mixtures were isostatically pressed, sintered, rolled and texture-annealed. SEM EDS analysis showed that copper and nickel atoms were completely mixed, while the alloying between the chromium powders and the nickel powders was incomplete. In spite of incomplete alloying between nickel and chromium powders, sharp cube-texture was developed for the Ni-13%Cr tape as well as the Ni-70%Cu tape.

• 한국세라믹학회지
• /
• 제31권6호
• /
• pp.595-600
• /
• 1994

Ni0.3Zn0.7Fe2O4 ferrite specimens were fabricated by dry pressing and tape casting method. The properties of each specimen were measured and compared. In order to design and manufacture the chip devices effectively, one important criterion can be that the sintered density of the laminated body should approach close to that of the dry pressed body which is regarded as standard. This requirement could be satisfied by controlling the solid loading of the ferrite sheet, lamination temperature and pressure. Using the optimum conditions (solid loading 55 wt%, lamination temperature 6$0^{\circ}C$, lamination pressure 400 kg/$\textrm{cm}^2$, sintered at 125$0^{\circ}C$ 2h) a sintered ferrite, with the density of 5.18g/㎤ and permeability of 1390 at 0.5 MHz, were obtained.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.22-23
• /
• 2005

In order to increase the critical current of coated conductor, highly Bi-axially textured substrates are required. Texture uniformity of substrate is also important to fabricate high quality superconducting coated conductor because the amount of current flow along the coated conductor is limited by the defects such as bad textured area. Therefore, we need to evaluate the distribution of texture of Ni substrate along the length before buffer layer deposition on Ni tape. R2R(reel-to-reel) XRD system was used to measure the texture of long Ni substrate continuously. $\theta-2\theta$ scan of 10 m long Ni tape was measured and indicates that some of Ni(111) planes equally remain on Ni(002) textured substrate. The results of continuous Ni(220) $\Phi$-scan indicate that average FWHM is 9$^{\circ}$ within $\pm$1.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.13-16
• /
• 2002

Ru thin films were deposited on bi-axially textured Ni tape using rf-magnetron sputtering for a conductive buffer layer of high Tc superconductor applications. (002) textured Ni films were fabricated as the deposition temperature was over $600^{\circ}C$. Rocking curves of the films showed similar alignment to those the Ni tapes. The resistivity of the tapes fabricated below $600^{\circ}C$ was around 20$\mu\Omega$-cm which is good for the conductive layer for tape superconductor applications.

• 에너지공학
• /
• 제2권3호
• /
• pp.293-299
• /
• 1993

용융탄산염연료전지(MCFC)용 다공성 Ni 양극에 3~10 wt% Al를 첨가하여 tape casting 법으로 제조된 Ni-Al 양극의 전기화학적성능 및 구조적안정성이 조사되었다. 본 연구에서 제조된 양극의 전기화학적 성능이 $650^{\circ}C$, MCFC 양극분위기(80% H$_2$＋20% $CO_2$)를 모사한 half-cell 에서 양분극 특성으로 평가되었는데, 전류밀도 150 ㎃/$\textrm{cm}^2$ 에서의 분극전압은 약 100 ㎷로 실용전지의 양극으로서 가능성을 보였다. Ni-Al 양극의 소결과 creep에 대한 저항성은 Ni 양극에 비해 증가되었는데, 이는 Ni 입자 표면에 형성된 $Al_2$O$_3$의 영향으로 판단되었다.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.95-98
• /
• 1999

The crystalline alignment of Ni substrates textured by RABiTS have a probability distribution in the surface plane. This makes it difficult to obtain a high quality of textures over all the range of a long Ni tape. In order to improve the textures of Ni tape, we have investigated a new method of texturing. We obtained non-cube textured Ni tapes by rolling and annealing a high purity Ni. In these tapes, the [001]-axes were tilted around the rolling direction, and the [100]-axes were parallel to the rolling direction. The average grain size was several cm$^2$. We deposited buffer layer (CeO$^2$/YSZ/CeO$^2$) and YBCO on those tapes. We found out that a YBCO film with grows normal with respect to the surface and this feature is independent of the tilting angles of the Ni [001]-axes.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.289-292
• /
• 2000

In order to evade the patent of Oak Ridge National Laboratory (RABiTS process) and search for more economical process, a new process for producing the biaxially textured Ni tape by electrodeposition has been investigated. Electrodeposition was performed in the modified Watts bath. The crystal orientations of electrodeposited Ni were analysed by X-ray pole figure, ${\phi}$-scan and ${\omega}$-scan. The electrodeposited Ni tape showed cube texture with good out-of plane(< 8${\circ}$) and in-plane alignment(< 20${\circ}$).

• 한국세라믹학회지
• /
• 제52권5호
• /
• pp.320-324
• /
• 2015

Optimization of the fabrication process of NiO-yttrium doped barium zirconate (BZY) composite anode substrates using tape-casting for high performance thin-film protonic ceramic fuel cells (PCFCs) is investigated. The anode substrate is composed of a tens of microns-thick anode functional layer laminated over a porous anode substrate. The macro-pore structure of the anode support is induced by micron-scale polymethyl methacrylate (PMMA) pore formers. Thermal gravity analysis (TGA) and a dilatometer are used to determine the polymeric additive burn-out and sintering temperatures. Crystallinity and microstructure of the tape-cast NiO-BZY anode are analyzed after the sintering.