• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.4
• /
• pp.71-78
• /
• 2017

New concept rotary engine initial prototype has been developed. Engine motoring, compressor pressure and fuel combustion were tested for engine mechanism and operability check. Merits and demerits, applicable areas of the engine have been investigated against reciprocating and Wankel rotary engines. It was found that this engine is best fit for small aircraft and it is better than existing engines for motorcycle, portable and hybrid car Genset too.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.17-23
• /
• 2002

In order to reduce exhaust emissions from diesel engine under wide operating range, an experimental study based on a new concept of combustion called HCDC(Homogeneous Charge Diesel Combustion) was conducted. In this concept, most of the fuel is supplied as premixed homogeneous charge and the rest is directly injected into a cylinder to ignite. In this study we compared combustion characteristics of an HCDC engine with those of conventional diesel engines. At high premixed fuel ratio and high load range, it was observed that premixed combustion heat release rate was low and diffusion combustion duration was shorten. from this experiment, it was found that NOx is reduced by the lower maximum temperature and soot is reduced by rapid combustion during diffusion combustion phase.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1907-1911
• /
• 2000

In this paper, classical vibration theories are summarized to design engine mount system of passenger vehicles. The vibrational characteristics of powertrain system and its equation of motion are introduced. Based upon the equation, the concept of the center of gravity, the principle inertia axis, the elastic center, and the elastic axis are defined and some new concepts are suggested. The theory of mode decoupling and the relationship between TRA (Torque Roll Axis) and roll mode are also reexamined to support the design concept of engine mount systems.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.4
• /
• pp.64-71
• /
• 2011

Homogeneous charge compression ignition (HCCI) was the best concept able to provide low NOx and PM in diesel engine emissions. This new alternative combustion process was mainly controlled by chemical kinetics in comparison with the conventional combustion in internal combustion engine. In this paper, detailed kinetic reaction mechanisms of diesel surrogate was investigated to understand the diesel HCCI engine combustion. It was tested two existing mechanisms and two new mechanisms for the comparison of experimental result. The best mechanism for diesel surrogate was suggested through this comparison.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.3
• /
• pp.324-329
• /
• 2004

As a new concept in engines and a power source for future automotive applications, the HCCI(Homogeneous Charge Compression Ignition) engine has been introduced. Essentially a combination of spark ignition and compression ignition engines, the HCCI engine exhibits low NO$_x$ and PM emissions as well as high efficiency under part load. In this research, a 4 cylinder diesel engine was converted into a HCCI engine, and propane was used as the fuel. The main parameters for this research are fuel flow rate and the temperature of the intake manifold, and the effects of such on a HCCI engine's performance and exhaust was investigated.

• Journal of Energy Engineering
• /
• v.14 no.4 s.44
• /
• pp.226-231
• /
• 2005

Essentially combination of spark ignition and compression ignition engines, the HCCI engine exhibits low NOx and Particulate Matter (PM) emissions as well as high efficiency under part load. This paper is concerned with the Homogeneous Charge Compression Ignition (HCCI) engine as a new concept in engines and a power source for future automotive applications. In this research, a 4 cylinder diesel engine was converted into a HCCI engine, and propane was used as the fuel. The purpose of this research is to show the effects of fuel flow rate and the temperature of the intake manifold on the performance and exhaust of an HCCI engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.6
• /
• pp.46-52
• /
• 2011

Homogeneous charge compression ignition (HCCI) is the best concept able to provide low NOx and PM in diesel engine emissions. This new alternative combustion process is mainly controlled by chemical kinetics in comparison with the conventional combustion in internal combustion engine. However, HCCI engine's operation have an excessive rate of pressure rising during the combustion process. In this study, stratification condition of EGR exhaust gases was used to reduce the pressure rising during the combustion process in HCCI engine. Also, combustion characteristics and emissions characteristics were investigated using the detailed diesel surrogate reaction mechanism.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.5
• /
• pp.58-64
• /
• 2002

A diesel engine has various merits such as high thermal-efficiency, superior fuel consumption and durability. Therefore the number of diesel engine in the world is increasing. As the seriousness of environmental pollution increases in the world, the method to reduce the noxious materials of CO2, NOx and P.M. is very important subject to correspond to exhaust gas regulations. A new concept, so called premixed charge compression ignition(PCCI), is focused among the various corresponding manners. In this study, we investigated the combustion characteristics of PCCI engine using a mixed fuels with that of commercial diesel engine. Finally we grasped a emission characteristics of PCCI engine. From this experiment, it could be found that NOx reduction is caused by the lower maximum temperature and soot reduction is caused by rapid combustion under diffusion combustion part. Also, it was found that 1st-combustion(cool flame) and 2nd-combustion(hot flame) is appeared in heat release curve, exhaust gas temperature is diminished and combustion variation is increased according to increasing of gasoline ratio.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.31-38
• /
• 2006

Cylinder liner rotation is a new concept for reducing piston assembly friction in the internal combustion engine. The purpose of cylinder liner rotation is to reduce the occurrence of boundary and mixed lubrication friction in the piston assembly. This paper reports the results of experiments to quantify the potential of the rotating liner engine. A GM Quad-4 SI engine was converted to single cylinder operation and modified for cylinder liner rotation. The hot motoring method was used to compare the friction loss between the baseline engine and the rotating liner engine. Additionally, tear-down tests were used to measure the contribution of each engine component to the total friction torque. The cycle-averaged motoring torque of the RLE represents a $23\~31\%$ friction reduction compared to the baseline engine for hot motoring tests. Through tear down tests, it was found that the piston assembly friction of the baseline engine is reduced from $90\%$ at 1200 rpm to $71\%$ at 2000 rpm through liner rotation.

• International Journal of Automotive Technology
• /
• v.5 no.3
• /
• pp.195-200
• /
• 2004

This paper is concerned with the Homogeneous Charge Compression Ignition (HCCI) engine as a new concept in engines and a power source for future automotive applications. Essentially a combination of spark ignition and compression ignition engines, the HCCI engine exhibits low NOx and Particulate Matter (PM) emissions as well as high efficiency under part load. The objective of this research is to determine the effects of Exhaust Gas Recirculation (EGR) rate on the combustion processes of HCCI. For this purpose, a 4-cylinder, compression ignition engine was converted into a HCCI engine, and a heating device was installed to raise the temperature of the intake air and also to make it more consistent. In addition, a pressure sensor was inserted into each of the cylinders to investigate the differences in characteristics among the cylinders.