• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.2
• /
• pp.200-213
• /
• 2000

Lasers have given dentistry a new rapid, economic, and accurate technique for metal joining. Although laser welding has been recommended as an accurate technique, there are some limitations with this technique. For example, the two joining surfaces must have a tight-fitting contact, which may be difficult to achieve in some situations. The tensile samples used for this study were made from a custom-made pure titanium and type III gold alloy plates. 27 of 33 specimens were sectioned perpendicular to their long axis with a carborundum disk and water coolant. Six specimens remained and served as the control group. A group of 6 specimens was posed as butt joints in custom parallel positioning device with a feeler gauge at each of three gaps : 0.00, 0.25. and 0.50mm. All specimens were then machined to produce a uniform cross-sectional dimension, none of the specimens was subjected to any subsequent form of heat treatment. Scanning electron microscopy was performed on representative tested specimens at fractured surfaces in both the parent metal and the weld. Vickers hardness was measured at the center of the welds with a micropenetrometer using a force of 300gm for 15 seconds. Measurement was made at approximately $200{\mu}m\;and\;500{\mu}m$ deep from each surface. One-way analysis of variance (ANOVA) and Scheffe's test was calculated to detect differences between groups. The purpose of this study is to compare the strength and properties of the joint achieved at various butt Joint gaps by the laser welding of type III gold alloy and pure titanium tensile specimens in an argon atmosphere. The results of this study were as follows : 1. When indexing and welding pure titanium, there was no decrease in ultimate tensile strength as compared with the unsectioned alloys for indexing gaps of 0.00 to 0.50mm, although with increasing gap size may come increased distortion (p>0.05). 2. When indexing and welding type III gold alloy, there were significant differences in ultimate tensile strength among groups with weld gaps of 0.00mm, 0.25 and 0.50mm, and the control group. Group with butt contact without weld gap demonstrated a significant higher ultimate tensile strength than groups with weld gaps of 0.25 and 0.50mm (p<0.05). 3. When indexing and welding the different metal combination of type III gold alloy and pure titanium, there were significant differences in ultimate tensile strength between groups with weld gaps of 0.00, 0.25, and 0.50mm. However, the mechanical properties of the welded joint would become too brittle to be acceptable clinically (p<0.05). 4. The presence of large pores in the laser welded joint appears to be the most important factor in controlling the tensile strength of the weld in both pure titanium and type III gold alloy.

• 한국벤처창업학회:학술대회논문집
• /
• 2008.04a
• /
• pp.143-178
• /
• 2008

This study is to look into the spin-off ventures which was incorporated based on the technology developed by public research institute, but underwent difficulties confronted during the development stages focused on the growth process and the factors contributed to their success. The case study was conducted with i-Sense Co., Ltd. which is a ventures organized by professors as a form of research based spin-off venture. i-Sense Co., Ltd. is a new-technology based ventures to produce self-tester for blood sugar level which was incorporated by Prof. Cha, Keun-sik and Prof. Nam, Hak-hyun of Department of Chemistry in Kwangwoon University along with the graduate course students of the Research Laboratory of the University. The two professors operated the Chemical Sensor Research Center at the Kwangwoon University where they produced many preliminary research outputs related with bio-sensors. They also executed the service works at the specialized company they established for research development to make research fund. They established i-Sense Co., Ltd. with the aim to carry out the research they want to. But contrary to the initial intention of the founders of the company, i-Sense Co., Ltd. has grown up as manufacturing company which produces and sells the self-tester for blood sugar level and is expected to be listed by Initial Public Offering (IPO) on the KOSDAQ in 2008. This study is to analyze the foundation and the growth process of i-Sense Co., Ltd. as successful research based spin-off ventures, to find out the factors contributed to their success by enabling them to overcome the difficulties experienced during the growth process, and eventually to provide with suggestive meanings in policy and practical point of view that leaded the research based spin-off ventures to success.

• The Journal of the Korea Contents Association
• /
• v.16 no.7
• /
• pp.231-241
• /
• 2016

The purpose of this study is to examine factors influencing social relations in elderly people participating in the Senior Employment Project and explore ways to improve their life quality by promoting the enhancing social relations in old age based on that. To attain the study goal, this researcher conducted hierarchical multiple regression analysis on 272 elderly persons having experience to participate a senior employment project selected through random sampling. According to the findings, elderly people's internal factors, self-esteem and external factor, job satisfaction, influence social relations in elderly people participating in the Senior Employment Project significantly. In other words, if elderly people participating in the Senior Employment Project have higher self-esteem, and job satisfaction, their social relations are better. Based on the results, this author provides political suggestions as follows: first, it is needed to develop policies and programs that can enhance elderly people's self-esteem. Second, it is necessary to acknowledge their worker's status, diversify business types and areas for them, and improve their labor conditions so that elderly people can show higher job satisfaction. Third, it is needed to develop both official and non-official support systems and build networks to form new social relations.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.12 no.2
• /
• pp.65-76
• /
• 2017

The purpose of this study is to promote the activation of creative problem - solving education in Korea through the case of countries leading education for creative problem solving in order to overcome the limitation of creative problem solving education in Korea. Based on 5 success factors by our cases of United States, Singapore, and Dublin City University in Ireland, we focused on the cases and extracted five key characteristics of creative problem solving education. The university should be able to provide various information gathering and theoretical knowledge for problem definition as well as continuing guidance and mentoring, rather than one-time teaching, in the form of teaching-student cooperative learning paradigm. Second, the class should be a team - based learning team which is a key factor in overseas universities' policy, so as to be able to identify differentiated, new ideas and creative problem solving methods based on knowledge and experience sharing. The creative problem solving method derived from education could be able to collect, organize, and apply to the field continuously and comprehensively about the learning process of the individual. Evaluation of curriculum should be based on characteristics of school and characteristics of students. The results of creative problem-solving education should be evaluated in order to continuously develop and create value in addition to the outcomes of the class. Therefore, it is necessary to develop an evaluation process for each university. The university should try to make creative problem solving education create value through specialization of university. Based on this, we propose a creative problem solving education framework.

• Archives of Plastic Surgery
• /
• v.38 no.2
• /
• pp.135-142
• /
• 2011

Purpose: Deficiencies of the abdominal wall can be the a result of infection, surgery, trauma, or primary herniation. For abdominal wall reconstruction, synthetic materials have been shown to provide a better long-term success rate than primary fascial repair. But, synthetic materials cannot elicit angiogenesis or produce growth factor and are therefore plagued by an inability to clear infection. As a result of the inherent drawbacks of synthetic, significant effort has been spent on the identification of new bioprosthetic materials. The aim of our study is to evaluate the effectiveness of a synthetic material (PROCEED$^{(R)}$) and an ADM ($SureDerm^{TM}$) to repair abdominal wall defects in a rabbit models. Methods: We measured the tensile strength of the $SureDerm^{TM}$ and PROCEED$^{(R)}$ by a Tension meter (Instron 4482). 16 Rabbit models were assigned to this study for abdominal wall reconstruction. Abdominal defect of 8 rabbits were reconstructed by PROCEED$^{(R)}$ and the rest were reconstructed by $SureDerm^{TM}$. We assessed gross and histologic examinations for the reconstructed abdominal wall. Results: The tensile strength of $SureDerm^{TM}$ and Gore Tex$^{(R)}$ is $14.64{\pm}0.51Mpa$, $8.54{\pm}0.45Mpa$. PROCEED$^{(R)}$ was estimated above the limits of measurement. Inflammatory reaction of PROCEED$^{(R)}$ persisted for 32weeks, but $SureDerm^{TM}$ decreased after 16weeks. Vascular ingrowth into the $SureDerm^{TM}$ was seen after 32 weeks. The basement membrane of $SureDerm^{TM}$ changed into a form of pseudoperitoneum. In PROCEED$^{(R)}$, it seemed like pseudoepithelial lining was made from the fibrosis around the mesh. Conclusion: In our study, the $SureDerm^{TM}$ not only have less inflammatory reaction and presented more angiogenesis than the PROCEED$^{(R)}$, but also have pseudoperitoneum formation. It is expected that $SureDerm^{TM}$ is useful for abdominal wall reconstruction. However, a long-term study of its usage consequences are thought to be needed.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.1
• /
• pp.37-44
• /
• 2009

A truss deck system that has replaced the slab form conventional method has become widely used in the construction of reinforced concrete structures as well as steel structures. The current commercial products, however, have some problems. The discontinuity between the lattice wires on the joint of the bottom wire induces vierendeel behavior, which increases the deflection of the system. In this research, a new truss deck system with continuous lattice wires on the level of the bottom wire was developed to reduce the system's vierendeel behavior and to improve its deformation capacity. To investigate the system's structural behavior, an experimental test and an analysis were performed. The main parameters of the test and analysis were the longitudinal shape and spacing of the lattices. To simulate the loading condition in the construction field, uniform construction loads were directly applied on the deck plates of the analysis model and the test specimens. The results of such analysis and test revealed that the longitudinal shape of the lattice wires is a major factor affecting the structural behavior of a steel wire truss deck. Thus, continuous lattice wires could result in decreased vierendeel behavior in the steel wire truss deck. It was also found that the truss deck system with lattices spaced longer than in the conventional products could be effectively used without increasing the member stresses.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.21 no.2
• /
• pp.444-452
• /
• 2007

Acupuncture treatment cures disease by regulating the functional excessiveness or deficiency which occurs in the meridian and visceral organs, and by letting stagnated Qi and Blood flow through the whole body and then controlling Qi. Whether or not to have Qi feeling is the main factor needed to manifest the efficacy of acupuncture. So it needs the very stimulus to make Qi felt rather than the simple stimulus. In order to have Qi feeling, it needs to acupuncture a patient according to patient's thinness or fatness, constitution, richness or poverty and age. And also it needs to vary the way to acupuncture a patient according to meridian, kinds of pulse, degrees of disease, new or old diseases, seasons with a disease and local areas of disease. In order to ascertain that it is important for the quality and quantity of acupuncture stimulus and the state of feeling acupuncture to get the efficacy of acupuncture, the experiment was planned to confirm whether the form and Qi of subject has different result according to the stimulated duration and depth. On the basis of the report that acupuncture on derma, when using electroacupuncture at Zusanli(ST 36) which denotes small intestinal motility, is more efficient than full depth acupuncture, I got the following result, after I observed whether the stimulated duration and depth give different efficacy according to the sex and weights of rat in experiment. The increased effects of small intestinal motility by electroacupuncture on Zusanli(ST 36) appeared after stimulating full depth for thirty minutes without distinction of sex and weights. This significant change was observed only in the female experimental group when I distinguished the sex. The small interstinal motility in rats by electroacupuncture at zusanli(ST 36) decreased in the 10 minutes' stimulated group and 30 minutes' stimulated group by duration on the one hand, and derma-deep stimulated group and full depth stimulated group by the depth of stimulus on the other hand, as the weights increased. This result shows that the duration and depth of acupuncture depends on the differences of acupuncture points, sex of the experimental animals, ages, and, weights. And the further study on the experimental and clinical differences and sextual differences need to be continued on.

• Korean Chemical Engineering Research
• /
• v.40 no.6
• /
• pp.729-734
• /
• 2002

In this study, the polyaniline films of emeraldine base(EB) and lucoemeraldine base(LEB) form chemically doping with poly(sodium-4 styrenesulfonate, PSS) were prepared by casting the mixed solution of chloroform and m-cresol on ITO(indium tin oxide) electrode. By analyzing UV-vis spectra of the mixed solutions, the effects of the secondary doping by m-cresol were obtained. And the conductivity of polyaniline film was increased with increasing m-cresol content. The results suggest that the improvement of conductivity obtained by secondary doping results primarily from interaction of polyaniline and m-cresol. As the results of analyzing cyclic voltammograms, it was known that the redox peak currents of polyaniline electrode prepared from LEB were larger and more reversible than those of polyaniline electrodes prepared from EB. The charge transfer resistances($R_{ct}$) of polyaniline electrodes were reduced with increasing m-cresol content, and LEB/PSS electrodes were smaller than EB/PSS electrodes. This result agrees to the analysis of the redox peak current of cyclic voltammograms. The solution resistance and the capacity of electrical double layer almost unchanged in all prepared polyaniline electrodes. It was confirmed that solution resistance was independent of frequency factor in AC impedance spectra. Also the polyaniline film doping with PSS was revealed pseudo n-type characteristics of conducting polymer.

• The Journal of Advanced Prosthodontics
• /
• v.1 no.2
• /
• pp.85-90
• /
• 2009

STATEMENT OF PROBLEM. Over the years, resin-bonded fixed partial dentures (RBFPDs) have gone through substantial development and refinement. Several studies examined the biomechanics of tooth preparation and framework design in relation to the success rate of RBFPDs and considered retention and resistance form essential for increase of clinical retention. However, these criteria required preparations to be more invasive, which violates not only the original intentions of the RBFPD, but may also have an adverse effect on retention due to loss of enamel, an important factor in bonding. PURPOSE. The object of this in vitro study was to compare the dislodgement resistance of the new types of RBFPDs, the conventional three-unit fixed partial denture, and conventional design of RBFPD (Maryland bridge). MATERIAL AND METHODS. Fifty resin mandibular left second premolars and second molars were prepared on dentiforms, according to the RBFPD design. After model fabrication (five group, n = 10), prostheses were fabricated and cemented with zinc phosphate cement. After cementation, the specimens were subjected to tensile loading at a cross head speed of 4 mm/min in a universal testing machine. The separation load was recorded and analyzed statistically using one-way analysis of variance followed by Duncan's multiple range test. RESULTS. Group V, the pin-retained RBFPDs, had the highest mean dislodgement resistance, whereas specimens of group II, the conventional RBFPDs, exhibited a significantly lower mean dislodgement resistance compared to the other 4 groups (P <.05). There were no significant differences between group I, III, and IV in terms of dislodgement resistance (P>.05). Group V had the highest mean MPa (N/$mm^2$) (P <.05). There was no significant difference between groups I, II, III and IV (P > .05). CONCLUSION. Within the limits of the design of this in vitro study, it was concluded that: 1. The modified RBFPDs which utilizes the original tooth undercuts and requires no tooth preparation, compared with the conventional design of RBFPDs, has significantly high dislodgement resistance (P < .05). 2. The modified RBFPDs which utilizes the original tooth undercuts and requires minimal tooth preparation, compared with the conventional FPDs, has significantly no difference in retention and dislodgement resistance)(P>.05). 3. The pin-retained FPDs showed a high dislodgement resistance compared to the conventional three-unit FPDs (P<.05).

• Water for future
• /
• v.24 no.3
• /
• pp.49-60
• /
• 1991

As a second part of the study entitled "Field Measurement and Analysis of Fluvial Sediment in the Cheongmi-Strea", this study concerns mineralogical and contaminative characteristics of sediment particles collected at Wonbu-Gyo and Hanpyeong-Gyo in the Cheongmi-Stream. The mineralogical analysis of the bed sediment collected reveals that, in general , quarz is the most abundant mineral found in sands with feldspars and rock fragments in the next, which confirms what is known in the literature. The shape factor of sand particles is about 0.7, which also agrees to what is known in the foreign literature. The analysis also reveals that the clay particles collected are composed mainly of illite, kaolinate, and chlorite. The analysis of contamination reveals that there is no substantial difference between the contents of organic material and heavy metals in the surface water and those in the pore water beneath the river bed. It is because the sampling for this analysis was conducted right after the September flood during which the fresh top soil from the upstream watershed replaced the old bed sediment and pore water that would probably be more contaminated. The contents of geavy metals in the bed sediment of sand particles do not exceed those in the soils adjacent to the river. For fine sediment such as clays, however, the contents of heavy metals, especially of mercury and zinc, far exceed those in the soils adjacent to the river. These fine sediments are transported downstream in the form of wash load and deposited in part on flood plains, which could be a new source of contaminants.taminants.