• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1905-1907
• /
• 1997

The experiments of laser-guided de discharge were carried out by using pulsed Nd:YAG laser radiation at low air pressure ranging from 0.3 to 20 torr. The minimum laser-guided de discharge voltages($V_{MD}$) at given pressure and distances between anode and cathode electrode were obtained. In order to generate TEM(transverse electromagnetic waves) modes, a pinhole was installed between a rod and a half mirror, and its diameter was adjusted from 6mm to 1.7mm. And then, we investigated the characteristics of laser-guided de discharge corresponding to different TEM modes. As a result, it was found that $V_{MD}$ at $TEM_{00}$ mode was lower than $V_{MD}$ at multimodes.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.103-105
• /
• 2005

Laser welding technology for automobile body is studied. laser system, robot and seam tracking system are used for 3D laser welding system The laser system is used 4kW Nd:YAG laser(HL4006D) of Trumpf and the robot system is used IRB6400R of ABB. The seam tracking system is SMRT-20LS of ServoRobot. The welding joints of steel plate are butt and lap joint. The 3-D welding for non-linear tailored blank is performed after experiments of bead on plate. Finally, the welding process for non-linear tailored blank is developed.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.3 no.2
• /
• pp.13-21
• /
• 1997

This paper describes the effectiveness of laser pulse shaping in eliminating weld defects such as porosity, cracks and undercuts in pulsed Nd:YAG Laser welding. A large porosity was formed in a keyhole mode of deep penetration weld metal of any stainless steel. Solidification cracks were present in Type 303 with about 0.3%s. The conditions for the formation of porosity were determined in further detail in Type 316. With the objectives of obtaining a fundamental knowledge of formation and prevention of weld defects, the fusion and solidification behavior of a molten puddle was observed during laser spot welding of Type 310S. through high speed video photographing technique. It was deduced that cellular dendrite tips grew rapidly from the bottom to the surface, and consequently residual liquid remained at the grain boundaries in wide regions and enhanced the solidification cracking susceptibility. Several laser pulse shapes were investigated and optimum pulse shapes were proposed for the reduction and prevention of porosity and solidification cracking.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.75-78
• /
• 2002

Si thin films on p-type (100) Si substrate have been prepared by a pulsed laser deposition technique using a Nd:YAG laser. The pressure of the environmental gas during deposition was 1 Torr. After deposition, Si thin film has been annealed again at 400-840$^{\circ}C$ in nitrogen ambient. Strong blue photoluminescence (PL) have been observed at room temperature. We report the PL properties of Si thin films with the variation of the annealing temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.539-542
• /
• 2000

ZnO thin films for light emission device have been deposited on sapphire and silicon substrates by pulsed laser deposition technique(PLD). A Nd:YAG laser was used with the wavelength of 355 nm. In order to investigate the emission properties of ZnO thin films, PL measurements with an Ar ion laser as a light source using an excitation wavelength of 351 nm and a power of 100 mW are used. All spectra were taken at room temperature by using a grating spectrometer and a photomultiplier detector. ZnO exhibited PL bands centered around 390, 510 and 640 nm, labeled near ultra-violet (UV), green and orange bands. Structural properties of ZnO thin films are analized with X-ray diffraction (XRD).

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.54-57
• /
• 2004

ZnO thin films on (001) sapphire substrates have been deposited by pulsed laser deposition(PLD) technique using an Nd:YAG laser with a wavelength of 266 m. During deposition, the experiment of the deposition of ZnO thin films has been performed for substrate temperatures in the range of $400^{\circ}C$ and flow rate of 350 sccm, films have been annealed at various substrate temperatures after deposition. After post-annealing treatment in the oxygen ambient, the structural properties of ZnO thin films were characterized by diffraction (XRD), SEM and the optical of the ZnO were characterized by photoluminescence (PL).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.95-98
• /
• 1999

ZnO thin films on (001) sapphire substrates have been deposited by pulsed laser deposition technique using a Nd:YAG laser with the wavelength of 355 nm. In order to investigate the effect of the deposition conditions on the properties of ZnO thin films at an oxygen pressure of 350 mTorr, the experiment has been Performed at various substrate temperatures in the range of 20$0^{\circ}C$ to $700^{\circ}C$. According to XRD, (002) textured ZnO films of high crystalline quality have been obtained and the intensity of UV emission was the highest at 40$0^{\circ}C$ substrate temperature.

• Journal of Welding and Joining
• /
• v.20 no.1
• /
• pp.41-46
• /
• 2002

A new laser welding system far the appendage of bearing pads of PHWR nuclear fuel elements has been developed. This system consists of laser oscillator, a optical fiber transmission, a monitoring device and a welding controller. The basic welding experiments of the appendage of Zircaloy-4 bearing pads were carried out. The laser welded samples were investigated and made by using the optical fiber of GI $400\mu\textrm{m}$. As a result, the seam welding with the bead width of 1.0mm and the weld penetration of 0.3mm could be accomplished.

• 한국가시화정보학회:학술대회논문집
• /
• 2002.11a
• /
• pp.101-104
• /
• 2002

Simultaneous measurement of turbulent velocity and concentration field in a stirred mixer tank is carried out by using PIV/LIF technique. Instantaneous velocity fields are measured by a $1K\times1K$ CCD camera adopting the frame straddle method while the concentration fields are obtained by measuring the fluorescence intensity of Rhodamine B tracer excited by the second pulse of Nd:Yag laser light. Image distortion due to the camera view-angle is compensated by a mapping function. It is found that the general features of the mixing pattern are quite dependent on the local flow characteristics during the rapid decay of mean concentration. However, the small scale mixing seems to be independent on the local turbulent velocity fluctuation.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.1
• /
• pp.139-146
• /
• 2001

This paper presents a study on heat transfer and residual distortion analysis of laser welded EDFA(Erbium Doped Fiber Amplifier) LD(Laser Diode) Pump using the finite element method. In the production process of LD Pump in light-wave communication system, ferrule and saddle are welded by Nd-YAG laser. These parts experience thermal and mechanical effect during heating and cooling cycle with the laser welding. Thus distortion happens in the laser-welded packaging, and it makes an error in detecting the light signal translate through optical fiber in LD Pump. The amount of final displacement produced by the laser welding is predicted using the finite element method. And the optimal shape of saddle is proposed with the results of numerical analyses to minimize the displacement.