• Transactions on Electrical and Electronic Materials
• /
• v.8 no.2
• /
• pp.84-88
• /
• 2007

[ $Bi_{1.5}Zn_{1.0}Nb_{1.5}O_7$ ] (BZN), $Bi_2Mg_{2/3}Nb_{4/3}O_7$ (BMN), and $Bi_2Cu_{2/3}Nb_{4/3}O_7$ (BCN) pyrochlore thin films were prepared on $Cu/Ti/SiO_2/Si$ substrates by pulsed laser deposition and the micro-structural and electrical properties were characterized for embedded capacitor applications. The BZN, BMN, and BCN films deposited at $25\;^{\circ}C$ and $150\;^{\circ}C$, respectively show smooth surface morphologies and dielectric constants of about $39\;{\sim}\;58$. The high dielectric loss of the films deposited at $150\;^{\circ}C$ compared with films deposited at $25\;^{\circ}C$ was attributed to the defects existing at interface between the films and copper electrode by an oxidation of copper bottom electrode. The leakage current densities and breakdown voltages in 200 nm thick-BMN and BZN films deposited at $150\;^{\circ}C$ are approximately $2.5\;{\times}\;10^{-8}\;A/cm^2$ at 3 V and above 10 V, respectively. Both BZN and BMN films are considered to be suitable materials for embedded capacitor applications.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.645-651
• /
• 1997

Tetragonal zirconia polycrystals (TZPs) doped with $Y_{2}O_{3}$ and $Nb_{2}O_{5}$ were prepared by the conventional sintering to enhance fracture toughness and phase stability of TZPs without controlling the grain size. TZP composites were obtained by adding the transformable TZP to the non-transformable TZP in wt%. The monolithic tetragonal $ZrO_2$, same as the composite composition containing 15 wt% transformable TZP, sintered at $1550^{\circ}C$ for 10h in air, exhibited the fracture toughness of 9$MPam^{1/2}$ and no low-and high-temperature degradation at temperatures in the range of 220 to $1000^{\circ}C$ for 100h in air. The corresponding single composition was 90.24 mol% $ZrO_2$-5.31 mol% $Y_{2}O_{3}$-4.75 mol% $Nb_{2}O_{5}$. The microstructure observation revealed that the t-$ZrO_2$ grains grew grandually with sintering time and no microcraking and twinning were observed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.5
• /
• pp.463-469
• /
• 1999

The potassium lithium niobate $K_3$$Li_2$$Nb_5$$O_{15}$ single crystals were growing in $K_x$$Li_{1-x}$$NbO_3$ (x = 0.4~0.6) chemical formular by the Czorchralski method. Crystal growth is studied in two orientations with growth along a-axis and c-axis. We have subjected this crystal to x-ray diffraction studies and found that they are single-crystalline and belong to tetragonal system with the lattice parameters a = b = 12.577 $\AA$ and c = 3.997$\AA$. The temperature dependence of dielectric constant was measured in the region of the phase transition. Curie temperature and diffuseness of phase transition are influenced by composition concentration. The composition and cation distribution of ferroelectric TB-type niobate crystals has a strong influence on the ferroelectric properties. Growth condition, optical transmittance, etching pattern and dielectric properties are presented and discussed.

• Corrosion Science and Technology
• /
• v.8 no.4
• /
• pp.143-147
• /
• 2009

In biomedical implants and dental fields, titanium has been widely utilized for excellent corrosion resistance and biocompatibility. However, Ti and its alloys are nonbioactive after being implanted in bone. In this study, for the purpose of improvement in biocompatibility the anodic $TiO_2$ layer on Ti-xNb alloys were fabricated by electrochemical method in phosphate solution, and the effect of Nb content on the pore size, the morphology and crystallinity of Ti oxide layer formed by the anodic oxidation method was investigated. The Ti containing Nb up to 3 wt%, 20 wt% and 40 wt% were melted by using a vacuum furnace. The sample were cut, polished, and homogenized for 24 hr at $1050^{\circ}C$ for surface roughness test and anodizing. Titanium anodic layer was formed on the specimen surface in an electrolytic solution of 1 M phosphoric acid at constant current densities ($30mA/cm^2$) by anodizing method. Microstructural morphology, crystallinity, composition, and surface roughness of oxide layer were observed by FE-SEM, XRD, EDS, and roughness tester, respectively. The structure of alloy was changed from $\alpha$-phase to $\beta$-phase with increase of Nb content. From XRD results, the structure of $TiO_2$ formed on the Ti-xNb surface was anatase, and no peaks of $Nb_2O_5$ or other Nb oxide were detected suggesting that Nb atoms are dispersed in $TiO_2$-based solid solution. Surface roughness test and SEM results, pore size formed on surface and surface roughness decreased as Nb content increased. From the line analysis results, intensity of Ti peak was high in the center of pore, whereas, intensity of O peak was high in the outside of pore center.

• Journal of Technologic Dentistry
• /
• v.23 no.2
• /
• pp.223-230
• /
• 2002

Pure titanium and Ti6Al4V alloy have been mainly used as implant materials but the cytotoxicity of V, neurotoxicity of Al resulting in Alzheimer disease had been reported. This paper was described the influence of composition of Ti-Nb alloys with 3 wt%Nb, 20 wt%Nb on the microstructure and corrosion resistance. Specimens of Ti alloys were melted in vacuum arc furnace and homogenized at $1000^{\circ}C$ for 24hr. The alloys were rolled in $\beta$ and ${\alpha}+{\beta}$ regions. The corrosion resistance of Ti alloys were evaluated by potentiodymic polarization test in 0.9% NaCl and 5% HCl solutions. The results can be summarized as follows: 1. The microstructure was transformed from $\alpha$ phase to ${\alpha}+{\beta}$ phase by adding Nb 2. The hardness of Ti-20Nb alloy was greater than Cp- Ti, Ti-3Nb alloy. 3. The corrosion resistance of Ti-20Nb alloy was better than that of Cp-Ti, Ti-3Nb alloy in 0.9%NaCl and 5%HCl solutions.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.237-242
• /
• 1998

Zr합금의 수소화 반응속도에 미치는 합금원소의 영향을 평가하기 위하여 Zr과 Zr-0.8Sn-XNb계열(X=0.2, 0.4, 0.8, 1.0) 및 Zr-0.4Nb-YSn계열(Y=0.5, 0.8, 1.5, 2.0)의 3원계 합금으로 electro-microbalance가 장착된 TGA (thermo-gravimetric apparatus)장치를 이용하여 40$0^{\circ}C$에서 1기압 수소와의 반응에 따른 무게증가를 in-situ로 측정하였다 Sn 첨가량이 증가함에 따라 1.5% 까지는 수소반응에 따른 무게증가율이 낮게 나타났으나 Sn을 2.0% 함유한 Zr-0.4Nb-2.0Sn합금의 경우 가장 높게 나타났다. 이는 Sn의 함량이 증가할수록 수소침투에 대한 저항성이 증가함을 의미하지만 Sn이 고용도 이상 함유되면 Sn을 함유한 다량의 석출물이 대량수소침투의 site로 작용하여 수소침투가 가속화된 것으로 평가된다. Nb의 경우 첨가량을 증가시킬수록 무게증가는 크게 나타났는데 이는 Nb이 수소흡수성이 크기 때문이며 Zr-0.8Sn-0.2Nb 및 Zr-0.8Sn-0.4Nb 합금보다 Zr-0.8Sn-0.8Nb 및 Zr-0.8Sn-1.0Nb 합금의 경우 TEM을 이용한 금속간 석출물(intermetallic precipitates) 분석에서 이러한 석출물들의 평균크기 및 개수가 크게 평가되었고, 또한 Zr-0.8Sn-0.2Nb, Zr-0.8Sn-0.4Nb 합금에서는 관찰이 되지 않는 $\beta$-Zr 석출물이 관찰되었다 이러한 사실로부터 Nb의 큰 수소흡수성에 부가적으로 이러한 석출물들이 수소침투를 가속화 하는 데에 기여하는 것으로 여겨진다.

• Korean Journal of Materials Research
• /
• v.25 no.8
• /
• pp.376-385
• /
• 2015

The effects of Nb and Cr addition on the microstructure, corrosion and oxide characteristics of Zr based alloys were investigated. The corrosion tests were performed in a pressurized water reactor simulated-loop system at $360^{\circ}C$. The microstructures were examined using OM and TEM, and the oxide properties were characterized by low-angle X-ray diffraction and TEM. The corrosion test results up to 360 days revealed that the corrosion rates were considerably affected by Cr content but not Nb content. The corrosion resistance of the Zr-xNb-0.1Sn-yCr quaternary alloys was improved by an increasing Nb/Cr ratio. The crystal structure of the precipitates was affected by a variation of the Nb/Cr ratio. The Zr-Nb beta-enriched precipitates were mainly formed in the high Nb/Cr ratio alloy while $Zr(NbCr)_2$ precipitates were frequently observed in the low Nb/Cr ratio alloy. The studies of oxide characteristics revealed that the corrosion resistance was related to the crystal structure of the precipitate.

• Journal of Welding and Joining
• /
• v.19 no.5
• /
• pp.506-511
• /
• 2001

Weld overlay has been developed to improve the property of material surface which is used in the severe environment. Weld overlay is the process which uses an arc heat and welds different composition of alloy on the substrate for the improvements of heat resistance and wear resistance. Weld overlay has a lot of advantages which are high hardness, good processing efficiency, easy controlling of layer thickness, good quality and low cost. In this study, weld overlay was performed by MAG welding on the base metal(SS400) with filler metal which contain composite powders(Cr+C+Mn+Mo+NbC) and solid wire(JIS-YGW11). Characterization of hardness and wear resistance were analyzed by EDS, EPMA, XRD and observations of microstructure were performed to investigate characteristics of overlays. The experimental results of overlaid specimens manufactured with Cr+C+Mn+Mo+NbC powders were obtained as fellows. ${\alpha}-phase$, M(Fe, Cr)3C and NbC of overlays were increased with decreasing the wire feed rates and increasing powder feed rates. Also the hardness of overlays were increased and the specific wear were decreased.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.552-553
• /
• 2006

The present study investigates the behavior of the sintering and hardness of stainless steel samples reinforced with NbC and TaC. Matrixes of pure stainless steel were compacted with addition of up to 3% wt NbC or TaC in a cylindrical die of steel $(\phi\;=\;5,0\;mm)$ at 700 MPa and sintered in an electrical resistance furnace under argon atmosphere. The sintered samples were characterized by density and hardness measurement, optical microscopy and scanning electron microscopy (SEM). The preliminary results show that the size and distribution of carbides influence in the sintering and hardness of the sintered samples.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.252-255
• /
• 1999

The effect of calcination temperature(1st and 2nd calcining at 110$0^{\circ}C$ , 120$0^{\circ}C$ and 130$0^{\circ}C$ respectively) on physical properties of BMNT Ceramics ware investigated. The optimum 1st and 2nd calcination temperature were 120$0^{\circ}C$ , and sintering temperature was 155$0^{\circ}C$. In this condition, the sintering density was 7.53 [g/㎤] and the dielectric constant, Q.f$_{0}$ and $\tau$$_{r}$ were 26, 80, 300[GHz] and +1.5[ppm/$^{\circ}C$] respectively in the microwave range.e.e.