• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.563-566
• /
• 2000

The effect of CuO and CuO-B $i_2$ $O_3$ additives on microwave dielectric properties of (P $b_{0.45}$C $a_{0.55}$)[F $e_{0.5}$N $b_{0.5}$)$_{0.9}$S $n_{0.1}$] $O_3$were investigated to decrease the sintering temperature for usage of Low Temperature Co-firing Ceramics (LTCC). The (P $b_{0.45}$C $a_{0.55}$)[F $e_{0.5}$N $b_{0.5}$)$_{0.9}$S $n_{0.1}$] $O_3$ceramics was sintered at 11$65^{\circ}C$. In order to decrease the sintering temperature, CuO and Cuo-B $i_2$ $O_3$ were added in the (Pb,Ca)[(Fe,Nb)Sn] $O_3$ with CuO-B $i_2$ $O_3$. For the addition of 0.4 wt.% CuO, the sintered density and the dielectric constant of the ceramics were revealed the maximum values of the 6.06g/c $m^2$ and 83 respectively and temperature coefficient of resonance frequency ($\tau$$_{f}$) shifted to the positive value. As increasing B $i_2$ $O_3$to the (Pb,Ca)[(Fe,Nb)Sn] $O_3$ with CuO-B $i_2$ $O_3$with 0.2 wt.% CuO, the sintered density, the $\varepsilon$$_{r}$ and the Q was decreased, and $\tau$$_{f}$ was minimized at 0.2 wt.% CuO, and 0.2 wt.% B $i_2$ $O_3$. For this composition, dielectric properties were $\varepsilon$$_{r}$ of 81, Q. $f_{0}$ of 4400 GHz, and $\tau$$_{f}$ of 5 ppm/$^{\circ}C$ at sintering temperature of 100$0^{\circ}C$. the relationship between the microstructure and properties of ceramics was studied by X-ray diffraction(XRD), scanning electron microscopy(SEM).copy(SEM).oscopy(SEM).copy(SEM).EM).

• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1252-1262
• /
• 1999

The effect of microstructures on the strength-flangeability of Nb bearing hot-rolled high strength steel was investigated in order to improve the strength-flangeability of conventional TS 580MPa grades HSLA steel for the automotive wheel disc. The low temperature coiling method using 3-step controlled cooling pattern after hot rolling was effective to produce the Nb-bearing high strength steel with the polygonal ferrite and bainite duplex microstructures. It was suggested that the suppressed precipitation of grain boundary cementites and the decreased hardness difference between ferrite matrix and bainite cause the excellent stretch-flangeability of ferrite-bainite duplex microstructure steel. Therefore, the formation and propagation of microcracks were suppressed relative to the conventional HSLA steel with ferrite and pearlite microstructure. In addition, the elongation was improved as compared with that of hot-rolled steel sheets using conventional early cooling pattern because the volume fraction of polygonal ferrite was increased.

• The Korean Journal of Ceramics
• /
• v.5 no.3
• /
• pp.255-259
• /
• 1999

The effects of $SiO_2$ and MnO addition on the sinterability and the electrical properties of 0.4mol% Nb-doped SrTiO3 varistor were investigated. The $SiO_2$ content was fixed at 0.3mol% and the MnO content varied from 0 to 1.0mol%. With 0.3 mol% $SiO_2$ and 0.3 mol% MnO addition, optimum density was obtained by sintering at $1200^{\circ}C$ without excess liquid phase. Impedance spectroscopy was performed on the sintered specimens with 0.3 mol% $SiO_2$ and various MnO contents. It was found that the resistivities of grains was increased with increasing MnO content. The dielectric constant was measured to be above 50000 in the specimen with 0.3~1.0mol% Mn content. The non-linear coefficient increased substantially with MnO addition, and it varied from 1 to 9 depending on the MnO content.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.3
• /
• pp.165-169
• /
• 2015

In this paper, in order to develop the composition ceramics with the excellent dielectric properties, $Pb(Mg_{1/2}W_{1/2})_{0.03}(Ni_{1/3}Nb_{2/3})_{0.09}(Zr_{0.5}Ti_{0.5})_{0.88}O_3$ ceramics were fabricated by the conventional solid-state method. The effects of ZnO addition on their microstructure and piezoelectric properties were systematically investigated. The rhombohedral-tetragonal phase coexistence has been found in the ceramics without ZnO content and then with further increasing ZnO content, specimens exhibited tetragonal phase. The optimized ZnO content formed liquid phase and aided the grain growth of specimens. When 0.4 wt% ZnO was added, the optimal physical properties ($d_{33}=422pC/N$, $d_{31}=161pC/N$, ${\varepsilon}_r=1,905$, $k_p=0.55$, $Q_m=160$) were obtained.

• Korean Journal of Materials Research
• /
• v.15 no.6
• /
• pp.413-418
• /
• 2005

Perovskite $Pb(Ni_{1/3}Nb_{2/3})O_3-Pb(Zr,Ti)O_3[PNN-PZT]$ ceramics were synthesized by conventional ceramic processing technique. In order to modify piezoelectric properties for sensor application in this system, NiO addition was considered to provide $Ni^{+2}$ as an acceptor, which was known to occupy with B site in the structure. The effect of NiO addition up to $8\;mol\%$ on the following piezoelectric properties as well as sintering properties was investigated. When NiO added more than $1\;mol\%$, average grain size was decreased and second phase was found to form. Moreover, the second phase caused decrease in relative dielectric constant $(\varepsilon_{33}T/\varepsilon0)$, electro-mechanical coupling factor $(k_p)$, and piezoelectric charge constant $(d_{33})$, while increasing mechanical quality factor $(Q_m)$. When $1\;mol\%$ NiO was added, density, dielectric properties and piezoelectric properties were abruptly increased.

• Journal of Magnetics
• /
• v.11 no.1
• /
• pp.43-50
• /
• 2006

In this paper, the influences of microstructural and surface morphological developments on the soft magnetic properties and giant magneto-impedance (GMI) effect of the $Fe_{73.5-x}Cr_{x}Si_{13.5}B_{9}Nb_{3}Au_1$ (x = 1, 2, 3, 4, 5) alloys have been presented. It was found that the Cr addition slightly decreased the mean grain size of $\alpha-Fe(Si)$ grains. AFM results indicate a large variation of surface morphology of density and size of protrusions along the ribbon plane due to microstructural changes caused by thermal annealing with increasing Cr content. Ultrasoft magnetic properties of the nanocrystallized samples were noticeably enhanced by properly heat treatments at $T_a=540^{\circ}C$ such as an increase of the magnetic permeability and the decrease of coercivity, which is likely due to the formation of nanoscale $\alpha-Fe(Si)$ phase which reduced the magnetoelastic anisotropy of samples. Accordingly, the GMI effect was observed in the annealed samples. The correlation between the microstructure, surface morphology, and soft magnetic properties were explained by nucleation and growth model.

• Journal of the Korean Ceramic Society
• /
• v.41 no.8
• /
• pp.633-636
• /
• 2004

The sintering behavior, microstructure and microwave dielectric properties of Ca $Ti_{0.5}$F $e_{0.25}$N $b_{0.25}$ $O_3$ with CuO have been investigated. Among the range of additions, 3 wt％ CuO was observed to perform most satisfactory for acting as a sintering aid. The dielectric properties were found to strongly depend on the sintered densities. The dielectric constant increased with sintering temperatures, while the Q${\times}$ $f_{0}$ value affected by second phase. For Ca $Ti_{0.5}$F $e_{0.25}$N $b_{0.25}$ $O_3$ with 3 wt％ CuO sintered at 100$0^{\circ}C$ for 2 h, the dielectric properties with an $\varepsilon$$_{r}$ value of 56, a Q${\times}$ $f_{0}$ value of 3,500 GHz and a $\tau$$_{f}$ value of 10 ppm/$^{\circ}C$ were obtained and suggested for practical applications.cations.ons.ons.ons.

• Smart Structures and Systems
• /
• v.8 no.1
• /
• pp.119-137
• /
• 2011

A bio-inspired two-mode structural health monitoring (SHM) system based on the Na$\ddot{i}$ve Bayes (NB) classification method is discussed in this paper. To implement the molecular biology based Deoxyribonucleic acid (DNA) array concept in structural health monitoring, which has been demonstrated to be superior in disease detection, two types of array expression data have been proposed for the development of the SHM algorithm. For the micro-vibration mode, a two-tier auto-regression with exogenous (AR-ARX) process is used to extract the expression array from the recorded structural time history while an ARX process is applied for the analysis of the earthquake mode. The health condition of the structure is then determined using the NB classification method. In addition, the union concept in probability is used to improve the accuracy of the system. To verify the performance and reliability of the SHM algorithm, a downscaled eight-storey steel building located at the shaking table of the National Center for Research on Earthquake Engineering (NCREE) was used as the benchmark structure. The structural response from different damage levels and locations was collected and incorporated in the database to aid the structural health monitoring process. Preliminary verification has demonstrated that the structure health condition can be precisely detected by the proposed algorithm. To implement the developed SHM system in a practical application, a SHM prototype consisting of the input sensing module, the transmission module, and the SHM platform was developed. The vibration data were first measured by the deployed sensor, and subsequently the SHM mode corresponding to the desired excitation is chosen automatically to quickly evaluate the health condition of the structure. Test results from the ambient vibration and shaking table test showed that the condition and location of the benchmark structure damage can be successfully detected by the proposed SHM prototype system, and the information is instantaneously transmitted to a remote server to facilitate real-time monitoring. Implementing the bio-inspired two-mode SHM practically has been successfully demonstrated.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.2
• /
• pp.157-165
• /
• 2016

This study investigated several anatomical characteristics of Paulownia tomentosa roots. The root wood was separated into three parts from stem base (top, middle, and base) at different positions below ground. Qualitative anatomical data suggested that the growth rings in earlywood and latewood were structurally different. Furthermore, the root wood vessels were found having 2 to 3 radial multiples and they were appeared in the form of clusters. In addition, some sheath cells and septate axial parenchyma were observed. Regarding the quantitative anatomical characteristics, vessel and ray numbers per $mm^2$, as well as ray width and height differed significantly among the top, middle, and base rood wood parts. However, there were no significant differences in vessel diameters, cell wall thickness, and width and length of wood fibers among those parts. The crystallinity of the root top part was slightly higher than that of the middle and base parts. Furthermore, the vessel numbers, ray numbers, and ray width and height in the near pith (NP) area were higher compared to those in the near bark (NB) area. However, the fiber width and fiber length at NP were lower than those at NB. Overall, this study demonstrated some significant differences in the anatomical characteristics of the top, middle, and base parts of root wood from Paulownia tomentosa.

• Korean Journal of Materials Research
• /
• v.15 no.2
• /
• pp.134-138
• /
• 2005

This study was performed to investigate the surface properties of electrochemically oxidized pure niobium by anodic oxide and hydrothermal treatment technique. Niobium specimens of $10mm\times10mm\times1.0mm$ in dimension were polished sequentially from $\#600,\;\#800,\;\#1000$ emery paper. The surface of pure niobium sperimens was anodized in an electrolytic solution that was dissolved calcium and phosphate in water. The electrolytic voltage was set in the range of 250 V and the current density was $10mA/cm^2$. The specimen was hydrothermal treated in high-pressure steam at $300^{\circ}C$ for 2 hours using an autoclave. And all specimens were immersed in the in the Hanks' solution nth pH 7.4 at $37^{\circ}C$ for 30 days. The surface of specimen was characterized by surface roughness, scanning electron microscope(SEM), energy dispersion X-ray analysis(EDX), X-ray photoemission spectroscopy(XPS) test. The value of surface roughness was the highest in the anodized sample and $0.41{\pm}0.04\;{\mu}m$. The results of the SEM observation show that oxide layers of the multi porosity in the anodized sample were piled up on another, and hydroxyapatite crystal was precipitate from the surface of the hydrothermal treated sample. In the XPS analysis, O, Nb, C peak and small amounts of N peak were found in the polished specimens while Ca and P peak in addition to O, Nb, C and peak were observed in the hydrothermal treated sample.