• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.453-459
• /
• 2001

It is important for the fabrication of nuclear cladding to optimize the microstructure, because the properties of Zr-based nuclear claddings such as mechanical properties, oxidation-resistance and corrosion- resistance vary widely with its microstructure. The microstructure in Zr-based alloy is strongly dependent on the solubility of alloying element. However, it is very difficult to measure the solubility due to the low solution limit of alloying elements in Zr-based alloy. In this study, Thermoelectric Power(TEP) measurements are used to determine the solubility of Nb in Zr-0.8Sn alloy, which is confirmed by optical microscopy and transmission electron microscopy. The solutioning of Nb obtained by a homogenization treatment and water-quench leads to a decrease of TEP The saturation of TEP appears with the increase of homogenization temperature, which means the saturation of the Nb content in the matrix. From these results, the solubility ($C_{Nb}$) of Nb in Zr-0.8Sn with temperature could be expressed as fellow equation : $4.69097{\times}10^{16}{\times}e^{-25300\times\;I/T}$(ppm.at.%)

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.4
• /
• pp.79-85
• /
• 2023

A novel low-temperature co-fired ceramic (LTCC) dielectric, composed of (1-4x)Bi_1.5Zn_1.0Nb_1.5O₇-3xBi₂Zn_2/3Nb_4/3O₇-2xLiZnNbO₄ (x=0.03-0.21), was synthesized through reactive liquid phase sintering of Bi_1.5Zn_1.0Nb_1.5O₇-xLi₂CO₃ ceramic at temperatures ranging from 850℃ to 920℃ for 4 hours. During sintering, Li₂CO₃ reacted with Bi_1.5Zn_1.0Nb_1.5O₇, resulting in the formation of Bi₂Zn_2/3Nb_4/3O₇, and LiZnNbO₄. The resulting sintered body exhibited a relative sintering density exceeding 96% of the theoretical density. By altering the initial Li₂CO₃ content (x) and consequently modulating the volume fraction of Bi_1.5Zn_1.0Nb_1.5O₇, Bi₂Zn_2/3Nb_4/3O₇, and LiZnNbO₄ in the final sintered body, a sample with high dielectric constant (ε_r), low dielectric loss (tan δ), and the temperature coefficient of dielectric constant (TCε) characterized by NP0 specification (TCε ≤ ±30 ppm/℃) was achieved. As the Li₂CO₃ content increased from x=0.03 mol to x=0.15 mol, the volume fraction of Bi₂Zn_2/3Nb_4/3O₇ and LiZnNbO₄ in the composite increased, while the volume fraction of Bi_1.5Zn_1.0Nb_1.5O₇ decreased. Consequently, the dielectric constant (εr) of the composite materials varied from 148.38 to 126.99, the dielectric loss (tan δ) shifted from 5.29×10^-4 to 3.31×10^-4, and the temperature coefficient of dielectric constant (TCε) transitioned from -340.35 ppm/℃ to 299.67 ppm/℃. A dielectric exhibiting NP0 characteristics was achieved at x=0.09 for Li₂CO₃, with a dielectric constant (ε_r) of 143.06, a dielectric loss (tan δ) value of 4.31×10^-4, and a temperature coefficient of dielectric constant (TCε) value of -9.98 ppm/℃. Chemical compatibility experiment with Ag electrode revealed that the developed composite material exhibited no reactivity with the Ag electrode during the co-firing process.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.61-66
• /
• 1997

월성1호기 압력관의 수소흡수 관련 자료들을 분석하였으며, 캐나다 발전소들의 결과와도 비교하였다. 압력관의 수소흡수 특성은 압력관내 위치, 사용온도, 가동이력 등에 영향을 받아 Inlet 쪽보다는 Outlet 쪽이, 사용온도가 높을수록, 또한 가동에 따른 조사량이 증가할수록 수소흡수량이 증가하였다. 한편 압력관내로의 수소흡수 거동을 규명하기 위해 Zr-2.5wt%Nb 합금의 열처리 조직 차이에 따른 수소흡수특성을 분석하였다. 수소흡수는$\alpha$-Zr 상에 비해 $\beta$-Zr, $\beta$-Nb 상에 크게 영향을 받는 것으로 보인다. 또한 합금내의 수소량 증가가 압력관 부식특성 자체에 미치는 영향을 분석하기 위하여 열처리 시편에 일정량의 수소를 charging 시킨 후 부식시험을 수행하였다. Zr-2.5wt%Nb 합금의 부식거동은 미세조직에 가장 큰 영향을 받아$\alpha$-Zr과 $\beta$-Zr 상의 시편이$\alpha$-Zr과$\beta$-Nb 상의 시편에 비해 큰 부식속도를 보였다. 또한 시편내 150ppm 이하의 수소함량은 시편의 부식거동에 별다른 영향을 없거나, 부식속도를 약간 감소시키는 것으로 추정된다.

• Journal of Ginseng Research
• /
• v.30 no.3
• /
• pp.137-152
• /
• 2006

This study is for chemical relationships between ginsengs(2, 3 and 4 yr) and soils from three representative soil types of Keumsan, shale(SL), phyllite(PH) and granite(GR). In the weathered soils, the GR is mainly high. Positive relationships are dominant, and negative correlations are shown in the Y-Nb and Nb-Ta pairs. In the field soils, the GR is high while the SL is low. Regardless of the localities, available correlation relationships are dominant in the GR, and dominant in the 3 year area. In the host rocks, high element contents are shown in the GR. Positive relationships, regardless of the localities, are shown in the Zr-Hf, Ta, Nb-Ta and Hf-Ta pairs. In the ginsengs, chemical contents are distinctive with the different ages. Positive relationships are shown in the Y-Nb pair of the SL, Rb-Y pair of the PH, and Rb-Sr pair of the GR. Relative ratios(GR/SL and GR/PH) of the ginsengs suggest that ginsengs from the GR are higher than those of SL and PH while in the comparisons between PH and SL, 2 year ginsengs are high in the SL and 4 year ginsengs are high in the PH. Relative ratios between weathered and field soils (weathered/field) suggest high element contents in the weathered soils from the SL and PH and in the relative ratios(weathered soil/host rock), high element contents in weathered soils. Relative ratios between field soils and ginsengs(field soil/ginseng), regardless of the ages, show several ten and hundred times, suggestive of high contents in the soils. Comparisons with the overall average contents of each area show differences of several ten to hundred times in the SL and PH, and of several to ten times in the GR. These relationships suggest that contents of the ginsengs from the GR are more similar to the soils relative to those of SL and PH.

• Korean Journal of Materials Research
• /
• v.3 no.6
• /
• pp.565-574
• /
• 1993

The Ar/Ar- $H_{2}$ plasma method Lvas applied to reduce and refine high purity Nb metal. Inaddition, the reaction between molten Nb metal and hydrogen were also analyzed in the Ar-(20%)$H_{2}$plasma. The metallic Nb of 99.5wt% was obtained at the ratio of $C/Nb_{2}O_{5}$=5.00 in the Ar plasma reductionand the $O_2$ loss from the thermal decomposition of niobium oxides did not take place. In the Ar-(20%)Hi plasma the metallic Nb of 99.8wt% was produced at the ratio of $C/Nb_{2}O_{5}$=4.80. It was observedthat a major reaction of the deoxidation was the reaction with H, Hi, and a deoxidation by the evaporationof $NbO_x$ did not occur but a mass loss of Nb did by a "splash" effect. The deoxidation reaction rateobeyed the 1st order reaction kinetics and the reaction rate constant(k') of deoxidation was $7.8 \times 10_{-7}$(m/sec).The solubility of hydrogen in Nb metal was 60ppm and it was larger than the solubility of molecularstate hydrogen by 40ppm in the Ar-(20%)$H_{2}$ plasma method. A saturation was within 60sec anda hydrogen content was reduced below lOppm by a Ar plasma re-treatment.by a Ar plasma re-treatment.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.64-71
• /
• 2003

In order to evaluate the effect of alloying elements (Nb and Sn) on the wear resistance of advanced Zr fuel claddings, sliding wear tests have been performed in room temperature air and water and these results were compared with those of commercial alloys such as Zircaloy-4, A and B alloys. As a result, the advanced Zr fuel claddings have a similar wear resistance compared with the commercial alloys. The wear resistance of the advanced Zr fuel claddings is closely releted to the content of Nb and Sn even though the effects of transition elements are involved in deforming wear properties. In the tested specimens with similar Sn content, wear volume became down to a minimum at $0.4\;wt\;\%$ Nb, then rapidly increased at 1.0 wt Nb. This behavior results in the variation of grain size with alloying contents. But Sn did not have a significant effect on the wear volume of advanced Zr fuel claddings below $1.1\;wt\%$. The relationship between alloying elements and wear behaviour was evaluated and discussed using material compatibility factor.

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.2
• /
• pp.88-95
• /
• 2022

Titanium alloy for bio-medical applications have been developed to reduce the toxicity of alloying elements and avoid the stress-shielding effect which is caused by relatively high elastic modulus compared to bone. Ti-39Nb-6Zr (TNZ40) alloy of elastic modulus exhibits around 40 GPa in the case of beta single phase. However, the strength of this alloy is lower than the other types of titanium alloys. Many research found that adding oxygen to beta-titanium alloys is beneficial for improving the strength through solid solution strengthening. In this study, TNZ40 ingots with addition of O were prepared by an arc remelting process (Ti-39Nb-6Zr-0.16O (wt.%), Ti-39Nb-6Zr-0.26O (wt.%)). Thermo-mechanical processing (i.e., heat treatment, cold swaging and aging heat treatment) has been performed under various conditions. Therefore, the aim of this study is to investigate the effect of oxygen content and ω phase formation on microstructure and mechanical properties.

• The Journal of the Petrological Society of Korea
• /
• v.26 no.2
• /
• pp.113-125
• /
• 2017

We investigates geochemical and tectonic characteristics for the Triassic Bojangsan trachyte in the southern margin of the Imjingang belt. The geochemical signatures of the thracyte are characterized by enrichments of REE and HFS, and show no Nb trough, suggesting that would not experience arc magmatic processes involving continental crustal materials. The trachyte reveals within-plate setting in tectonic discrimination diagrams using immobile HFS Nb and Y elements. And the trachyte shows typical signatures of A-type volcanic rocks with high Ga abundance and is classified as A1-type volcanic rocks rich in Nb. The geochemical signatures suggest that the trachyte was produced by the differentiation of mantle-derived magmatism at the continental rift in extensional setting subsequent to a major collision during the Permo-Triassic Songrim orogeny. The results provide robust evodence to consider the Imjingang belt as an extension of the the Qinling-Dabie-Sulu belt between the North and South China blocks.

• Journal of the Mineralogical Society of Korea
• /
• v.24 no.2
• /
• pp.133-143
• /
• 2011

In Mujoo area, the granitic pegmatites are developed in the granitic gneiss complex with Jurassic gneissic granites, where Nb-Ta mineralization were reported. Pegmatites are mainly composed of large crystals of quartz, feldspars of end-member orthoclase and albite, and muscovite. Nb-Ta minerals in study area are columbite (Nb > Ta) in composition. Chemistry of muscovites shows post-magmatic in origin and they are closely related with columbite. Large columbite, in pegmatites occurred with quartz and feldspars, while microcrystalline columbite is associated with muscovite. The Nb contents in large columbite are relatively higher than those in microcrystalline ones. Two pegmatites, 4~15 m in width and 120 m, 250 m in extension respective1y, are developed. Five drilling cores with total 600 m in length are finally obtained and revealed no possible potential for economic rare metals of Na-Ta deposits.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.231-236
• /
• 1998

원자력 발전소의 핵연료 피복관 재료로 사용되고 있는 Zr합금의 부식특성에 미치는 Sn의 영향을 조사하기 위해 Sn 함량을 0.5, 0.8, 1.5, 2.0wt.%로 조절한 Zr-xSn 2원계 합금과 Zr-0.4Nb-xSn 3원계 합금을 제조하여 36$0^{\circ}C$ 물 분위기의 mini-autoclave에서 부식실험을 수행하였다. 2원계 합금에서 Sn이 0.5, 0.8, 1.5wt.% 첨가된 합금에서는 15일에서 속도천이가 발생한 후 급격한 부식 가속 현상이 나타났으나, 2.0wt.%가 첨가된 합금에서는 100일까지 부식 실험에서도 천이 현상을 보이지 않는 매우 높은 부식 저항성을 보였다. 그러나 3원계 합금에서는 2원계 합금과는 달리 40일 시험에서도 모든 합금들이 속도 천이 현상을 보이지 않고 천이전 영역에서의 부식 거동을 보이며, Sn 함량 변화에 따른 부식 속도의 차이를 감지할 수 없었다. 이러한 경향은 2원계 합금과 3원계 합금에서 Sn의 고용도 차, 미량 첨가된 Nb의 영향 및 석출물의 특성과 관련이 있는 것으로 사료된다. 또한 수소 흡수율면에서도 Sn 함량 변화에 따라 부식 거동과 비슷한 경향을 보이면서 2.0wt.%에서 가장 낮은 수소흡수율을 보였다 천이전 영역에서 산화막 구조 관찰 결과 천이전 영역의 모든 산화막에서 보호적 성질을 나타내는 tetragonal-ZrO$_2$가 관찰되었는데, tetragonal-ZrO$_2$의 분율은 Sn 함량에 따라 거의 같게 나타났다.