• New & Renewable Energy
• /
• v.16 no.1
• /
• pp.15-24
• /
• 2020

For mechanical load testing of wind turbines, capture matrix is constructed for various range of wind speeds according to the international standard IEC 61400-13. The conventional method wastes considerable amount of data by its invalid data policy -segment data into 10 minutes then remove invalid ones. Previously, we have suggested an alternative way to save the total amount of data to build a capture matrix, but the efficient selection of data has been still under question. The paper introduces optimization algorithms to construct capture matrix with less data. Heuristic algorithm (simple stacking and lowest frequency first), population method (particle swarm optimization) and Q-Learning accompanied with epsilon-greedy exploration are compared. All algorithms show better performance than the conventional way, where the distribution of enhancement was quite diverse. Among the algorithms, the best performance was achieved by heuristic method (lowest frequency first), and similarly by particle swarm optimization: Approximately 28% of data reduction in average and more than 40% in maximum. On the other hand, unexpectedly, the worst performance was achieved by Q-Learning, which was a promising candidate at the beginning. This study is helpful for not only wind turbine evaluation particularly the viewpoint of cost, but also understanding nature of wind speed data.

• Journal of Power Electronics
• /
• v.18 no.4
• /
• pp.1111-1126
• /
• 2018

In modern power systems, distributed generators (DGs) result in high stress on system frequency stability. Apart from the intermittent nature of DGs, most DGs do not contribute inertia or damping to systems. As a result, a new control method referred to as a virtual synchronous machine (VSM) has been proposed, which brought new characteristics to inverters such as synchronous machines (SM). DGs employing an energy storage system (ESS) provide inertia and damping through VSM control. Meanwhile, energy storage presents some physical constraints in the VSM implementation level. In this paper, a VSM mathematical model is built and analyzed. The dynamic responses of the output active power are presented when a step change in the frequency occurs. The influences of the inertia constant, damping factor and operating point on the ESS volume margins are investigated. In addition, physical constraints are proposed based on these analyses. The proposed physical constraints are simulated using PSCAD/EMTDC software and tested through RTDS experiment. Both simulation and RTDS test results verify the analysis.

• Journal of Korean Ophthalmic Optics Society
• /
• v.3 no.1
• /
• pp.115-120
• /
• 1998

The $TiN_x$ thin films were prepared on glass substrate by RF(radio-frequency) magnetron sputtering apparatus from a Ti target in a gaseous mixture of argon and nitrogen. In deposition, a RF power supply was used as a power source with a constant power of 240W, and the substrate was heated to $200^{\circ}C$. The films were obtained at nitrogen flow rates in the range 3-9 seem with a constant argon flow rate of 20 seem. For the films obtained, the chemical binding energy of the films was investigated by XPS (x-ray photoelectron spectroscopy) in order to analyze the chemical nature and composition of the films.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.1
• /
• pp.21-25
• /
• 1999

The TiN, thin films were prepared on glass substrate by RF(radio-frequency) magnetron sputtering apparatus from a Ti target in a gaseous mixture of argon and nitrogen. In deposition, a RF power supply was used as a power source with a constant power of 240W, and the substrate was heated to $200^{\circ}C$. The films were obtained at nitogen flow rates in the range 3-9 sccm with a constant argon flow rate of 20 secm. For the films obtained, the sheet resistance and the chemical binding energy of the films was observed by four-point-probe method and x-ray photoelectron spectroscopy(XPS) depth profiling respectively. In addition, we investigated the relationship between the surface resistance and the chemical nature of the films.

• Journal of Power Electronics
• /
• v.12 no.4
• /
• pp.623-631
• /
• 2012

In this paper, a digital controller design procedure is presented for single-phase voltage-doubler boost rectifiers (VDBR). The model derivation of the single-phase VDBR is performed in the s-domain. After that the simplified equivalent z-domain models are derived. These z-domain models are utilized to design the input current and the output dc-link voltage controllers. For the controller design in the z-domain, the traditional K-factor method is modified by considering the nature of the digital controller. The frequency pre-warping and anti-windup techniques are adapted for the controller design. By using the proposed method, the phase margin and the control bandwidth are accurately achieved as required by controller designers in a practical frequency range. The proposed method is applied to a 2.5 kVA single-phase VDBR for Uninterruptible Power Supply (UPS) applications. From the simulation and the experimental results, the effectiveness of the proposed design method has been verified.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.12
• /
• pp.874-887
• /
• 1987

The efficiency of a synchronous motor can be substantially improved by controlling armature voltage, field excitation, and load angle on optimum values which yield minimum input power at any specified torque and speed. This improvement is particularly noticeable in the case of light loads. In addition, the control of armature input voltage improves the power factor at which the motor operates. Employed in the analysis is a new equivalent circuit model of the motor which incorporates the frequency dependent nature of the motor parameters and the effects of iron loss. The stability of synchronous motor operation is studied by applying the Nyquist stability criterion to the linearized equations which describe the behavior of the motor as the motor loads perturb about a steady-state operating point. This investigation reveals that, in some cases, the stable region of the motor is delineated from the results of a computer simulation. With a view to reducing harmonic loss and improving torque pulsation from harmonic components, a very poweful pulse amplitude modulation (PAM) method using an 16-bit microcomputer has been developed. This method has the advantages of simplicity of control algorithms and requires small memory space for storing thyristor trigger angles for a three-phase PAM inverter. The method can be used for smooth control of both modulation depth and frequency over a wide range.

• Structural Monitoring and Maintenance
• /
• v.2 no.1
• /
• pp.1-18
• /
• 2015

Traditionally, it is not easy to carry out tests to identify modal parameters from existing railway bridges because of the testing conditions and complicated nature of civil structures. A six year (2007-2012) research program was conducted to monitor a group of 25 railway bridges. One of the tasks was to devise guidelines for identifying their modal parameters. This paper presents the experience acquired from such identification. The modal analysis of four representative bridges of this group is reported, which include B5, B15, B20 and B58A, crossing the Caraj$\acute{a}$s railway in northern Brazil using three different excitations sources: drop weight, free vibration after train passage, and ambient conditions. To extract the dynamic parameters from the recorded data, Stochastic Subspace Identification and Frequency Domain Decomposition methods were used. Finite-element models were constructed to facilitate the dynamic measurements. The results show good agreement between the measured and computed natural frequencies and mode shapes. The findings provide some guidelines on methods of excitation, record length of time, methods of modal analysis including the use of projected channel and harmonic detection, helping researchers and maintenance teams obtain good dynamic characteristics from measurement data.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.209-212
• /
• 2006

Insect and birds in nature flap their wings to generate fluid dynamic forces that are required for the locomotion. Most of the previous published papers discussed mainly on the effect of flapping parameters such as flapping frequency and amplitude on the thrust at a fixed Reynolds number. However, it is not much known on the values of the flapping parameters that the flapping wing requires to generate the thrust at the low Reynolds number flow. In this paper, the onset of the thrust generation is investigated using the lattice Boltzmann method. The wake patterns and velocity profiles behind a flat plate in heaving oscillation are investigated for the heaving amplitude of 0.5C. The time-averaged thrust coefficient value is investigated by changing the reduced frequency from 0.125 to 3.0 for three values of heaving amplitude (h/C=0.25, 0.325, 0.50). It is also found that the critical Strouhal number over which the flat plate starts to produce the thrust is around 0.1 and the thrust is an exponential function of the Strouhal number.

• Wind and Structures
• /
• v.12 no.2
• /
• pp.103-120
• /
• 2009

Articulated tower platforms due to its compliant nature are more susceptible to the dynamic effects of wind than conventional fixed platforms. Dynamic response analysis of a double hinged articulated tower excited by low frequency wind forces with random waves is presented in this paper. The exposed super structure of the platform, housing the drilling and production facilities is subjected to mean and fluctuating wind loads, while the submerged portion is acted upon by wind driven waves. The fluctuating component of the wind velocity is modeled by Emil Simiu's spectrum, while the sea state is characterized by Pierson-Moskowitz spectrum. Nonlinearities in the system due to drag force, added mass, variable submergence and instantaneous tower orientation are considered in the analysis. To account for these nonlinearities, an implicit time integration scheme (Newmark's-${\beta}$) has been employed which solves the equation of motion in an iterative fashion and response time histories are obtained. The power spectra obtained from random response time histories show the significance of low frequency responses.

• Journal of Forest and Environmental Science
• /
• v.30 no.1
• /
• pp.126-132
• /
• 2014

This experiment was conducted to establish the in vitro propagation of Dendrobium moniliforme through protocorm like body (PLB) induction from the culture of leaf, stem and root explants. Frequency of PLB formation from root explants was higher than those of leaf and stem explants. PLB's proliferation in MS medium including 1.0 mg/L NAA was better than 1.0 mg/L IBA. Frequency of PLB's proliferation on medium with various concentrations of BA, Kinetin, Tidiazuron (0. 1.0, 3.0 mg/L) and NAA (0, 1.0 mg/L) was tested. The maximun proliferation of PLB's was obtained on MS medium supplemented with 3.0 mg/L BA and 1.0 mg/L NAA after 6 weeks of culture. Addition of 200 mg/L activated charcoal (AC) and 30 g/L sucrose was effective on PLB proliferation for D. moniliforme.