• Journal of Korea Water Resources Association
• /
• v.47 no.7
• /
• pp.599-614
• /
• 2014

In this study, two dimensional finite volume model was parallelized to improve computing time, which has been developed to be able to apply for the mixed meshes of triangle and quadrilateral. MPI scheme which is free from limitation of the number of cores was applied, and non-blocking point-to-point communication was used for fluxes and time steps calculation domain. The developed model is applied to analyze dam break in a L-shaped experimental channel with $90^{\circ}$ bend and Malpasset dam breach event to calibrate the consistency between parallelized model and existing model and examine the speed-up and efficiency of computing time. Computational speed-up about the size of the input data was considered by simulating 4 cases classified by the number of meshes, Consequently, the simulation results reached a satisfactory accuracy compared to measured data and the results from existing model, and achieved more than 3 times benefit of computational speed-up against computing time of existing model. Simulation results of 3 cases classified by the size of input data lead us to the conclusion that it is important to use proper size of input data and the number of process in order to minimize the communication overhead.

• Korean journal of applied entomology
• /
• v.45 no.2 s.143
• /
• pp.119-129
• /
• 2006

The antennal receptors of the adult male and female of the American leafminer, Liriomyza trifolii (Diptera: Agromyzidae) was studied using the scanning electron microscopy. This antennal receptors were developed to accept the chemical or mechanical signal in the environment. The antennae of L. trifolii is 317.52 $\mu$m long and composed of the scape, pedicel, funicle, arista. Antennae located between compounds eye on the middle in the head. The result of SEM observation, four types of receptors were characterized and grouped into morphological classes: Trichoid, Basiconic, Coeloconic, Chetiform sensilla. Trichoid sensilla are located on the all segment. As a rule, female is more than male. This sensilla are long and slender hair with straight or slightly curved, and taper to a sharp point apically. Basiconic sensilla are observed only on the funicle. The number of basiconic sensilla in male and female are almost same in both sexes. This sensilla are long and thick hair with stright or slightly curved, and taper to a blunt point apically. Coeloconic sensilla are observed only on the funicle. This sensilla were showed a finger-like projections the peg apex. The number of basiconic sensilla in male and female are almost same in both sexes. Chetifarm sensilla are located on the all segment. This sensilla are needle-like, tapering sharply. Pedicel are more than scape. The number of Chetiform sensilla in male and female are almost same in both sexes.

• Korean Journal of Veterinary Pathology
• /
• v.1 no.1
• /
• pp.1-6
• /
• 1997

The cellularity and composition of the spleen lymph node thymus and peripheral blood and tempo of regeneration were studied at various time points after syngeneic bone marrow transplantation(BMT) in C3H/Hen mice. Significant depression of absolute lymphocyte count was noted on week 1 after lethal whole-body irradiation and BMT. In comparison to the lymph node thymus and spleen had an rapid regeneration of cellularity. The distinct cell populations($CD4^+,\;CD8^+,\;CD28^+,\;B220^+) have determined in the lymphoid tissue of mice subjected to irradiation. The relative representation of these subpopulations was significantly different from that in nonirradiated control. $CD4^+\;and\;CD8^+$ cells were present in very low numbers whereas the $B220^+$ cells reached more than normal range at 2 weeks after BMT. The number of $CD4^+$ cells returned to normal relatively soon than $CD8^+$ cell. At week 4 after BMT, the cellularity and composition of spleen lymph node and peripheral blood lymphocyte reached about 50% of the normal range therefore we can choose this time point for the other tests of immune function after BMT.

• Journal of the korean society of oceanography
• /
• v.32 no.4
• /
• pp.163-170
• /
• 1997

Some CMP gathers acquired from shallow marine seismic reflection survey in offshore Korea do not show the hyperbolic trend of moveout. It originated from so-called swell effect of source and streamer, which are towed under rough sea surface during the data acquisition. The observed time deviations of NMO-corrected traces can be entirely ascribed to the swell effect. To correct these time deviations, a residual statics is introduced using Genetic Algorithms (GA) into the swell correction. A new class of global optimization methods known as GA has recently been developed in the field of Artificial Intelligence and has a resemblance with the genetic evolution of biological systems. The basic idea in using GA as an optimization method is to represent a population of possible solutions or models in a chromosome-type encoding and manipulate these encoded models through simulated reproduction, crossover and mutation. GA parameters used in this paper are as follows: population size Q=40, probability of multiple-point crossover P$_c$=0.6, linear relationship of mutation probability P$_m$ from 0.002 to 0.004, and gray code representation are adopted. The number of the model participating in tournament selection (nt) is 3, and the number of expected copies desired for the best population member in the scaling of fitness is 1.5. With above parameters, an optimization run was iterated for 101 generations. The combination of above parameters are found to be optimal for the convergence of the algorithm. The resulting reflection events in every NMO-corrected CMP gather show good alignment and enhanced quality stack section.

• Korean Journal of Agricultural Science
• /
• v.49 no.3
• /
• pp.571-582
• /
• 2022

Cacao, a major ingredient for making chocolate, has been shown to have potent antioxidant effects. The consumption of raw cacao has beneficial effects on health. This study determined the fermentation properties of yoghurt that was manufactured with cacao nibs (Theobroma cacao L.). The pH of the yogurt containing the cacao nibs was lower than that of the control, and this reduction was both concentration and fermentation time-dependent. Furthermore, the number of lactic acid bacteria in the yogurt made with cacao and its viscosity increased in a cacao nibs dependent manner. In particular, the yoghurt with 5% cacao nibs added had the highest number of lactic acid bacteria at 48 hours at the end point of the fermentation. Whey protein degradation in yogurt containing cacao nibs increased with the fermentation time, and the organic acid production, especially lactic acid, in the yogurt containing cacao nibs increased significantly after 16 hours of fermentation. In addition, the total polyphenol content of the yogurt containing cacao nibs increased, which was proportional to the amount added. Sensory evaluations of the yogurts indicated that overall taste was less desirable as cacao nib loadings increased from 1 to 5% compared with controls. This result is due to the excessive acidity, which was strongly perceived in the absence of added sugar. The development of yogurts with cacao nibs is expected to contribute much to the appeal of fermented milk.

• Smart Structures and Systems
• /
• v.31 no.3
• /
• pp.275-281
• /
• 2023

In recent years, technological developments have rapidly increased the number of complex structures and equipment in the industrial. Accordingly, the prognostics and health monitoring (PHM) technology has become significant. The safety assessment of industrial sites requires data obtained by installing a number of sensors in the structure. Therefore, digital twin technology, which forms the core of the Fourth Industrial Revolution, is attracting attention in the safety field. The research on digital twin technology of structures subjected to seismic loads has been conducted recently. Hence, this study proposes a digital twin system that estimates the responses and arbitrary load in real time by utilizing the minimum sensor to a pipe that receives a seismic and arbitrary load. To construct the digital twin system, a finite-element model was created considering the dynamic characteristics of the pipe system, and then updating the finite-element model. In addition, the calculation speed was improved using a finite-element model that applied the reduced-order modeling (ROM) technology to achieve real-time performance. The constructed digital twin system successfully and rapidly estimated the load and the point where the sensor was not attached. The accuracy of the constructed digital twin system was verified by comparing the response of the digital twin model with that derived by using the load estimated from the digital twin model as input in the finite-element model.

• The Journal of Korean Academy of Prosthodontics
• /
• v.36 no.6
• /
• pp.858-866
• /
• 1998

Soldering is the usual method used to correct an unstable fixed partial denture framework at patient's try-in; However, presoldering base metal alloys is technique-sensitve and results are unstable because it is difficult to maintain uniform heat distribution and to prevent oxidation of an alloy. A cast-joining technique has been developed by Weiss and Munyon for repair, correction and addition to base metal framework. This joining technique eliminates the problem with presoldering of non-precious frameworks. The object of this study was to 1) compare the relative flexure strength and the joining effectiveness of Ni-Cr-Be cast in two pieces and 'pre-soldered' versus in two pieces and 'cast-joined'. 2) determine the effect of increasing the number of retentive grooves on the face of the cast and 3) determine the effect of the relative matched position of groove patterns on flexure strength. The joining effectiveness can be expressed by the ratio of the mean flexure stress of soldered or cast-joined specimens to that of one-piece cast. Resin rods 3mm in diameter were used as pattern of specimens for one-piece casted, presoldered, and cast-joined groups. Cast-joined specimens had two different patterns of retentive grooves on the joined faces. Type A had cross-shaped grooves 1mm in depth. 0.6mm in width. Type B was the same except for the addition of one more retentive groove. In the experiment connecting cast-joined specimens, half of specimens with type A pattern had their patterns on the faces of paired casts matched with each other as mirror image. With the rest pairs, it was proceeded that one of paired casts turned 45 degrees so that the patterns crossed. Half of specimens with type B pattern also had the patterns matched as mirror image; However, here, one of paired casts turned 90 degrees with the other pairs. Retentive groove in this study lacked the intentional undercuts, in contrast with the suggestion of Weiss and Munyon. The specimens were subjected to four-point flexural loading in an Instron testing machine. The midspan flexural stress was calculated at the point of initial plastic strain as determined from a strip-chart recorder or at the point of failure if this occured at a lower stress level. Within the scope of this study, the following results were obtained. 1. The presoldered group showed flexural strength at least 2 times higher than the cast-joined groups. Its joining effectiveness was 82%. 2. In cast-joined groups, the flexural strength of joints with type B patterns exhibited 1.5 times that of joints with type A patterns. Joining effectivenesses were 38% for type B patterns, 25-26% for type A patterns. 3. The relative matched position of groove patterns did not have any significant effect on flexural strength of the cast-joined specimens with either type A patterns or type B patterns(p>.05).

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.408-415
• /
• 2022

In this paper, we propose a 3D point cloud reconstruction technique from 2D images using efficient feature map extraction network. The originality of the method proposed in this paper is as follows. First, we use a new feature map extraction network that is about 27% efficient than existing techniques in terms of memory. The proposed network does not reduce the size to the middle of the deep learning network, so important information required for 3D point cloud reconstruction is not lost. We solved the memory increase problem caused by the non-reduced image size by reducing the number of channels and by efficiently configuring the deep learning network to be shallow. Second, by preserving the high-resolution features of the 2D image, the accuracy can be further improved than that of the conventional technique. The feature map extracted from the non-reduced image contains more detailed information than the existing method, which can further improve the reconstruction accuracy of the 3D point cloud. Third, we use a divergence loss that does not require shooting information. The fact that not only the 2D image but also the shooting angle is required for learning, the dataset must contain detailed information and it is a disadvantage that makes it difficult to construct the dataset. In this paper, the accuracy of the reconstruction of the 3D point cloud can be increased by increasing the diversity of information through randomness without additional shooting information. In order to objectively evaluate the performance of the proposed method, using the ShapeNet dataset and using the same method as in the comparative papers, the CD value of the method proposed in this paper is 5.87, the EMD value is 5.81, and the FLOPs value is 2.9G. It was calculated. On the other hand, the lower the CD and EMD values, the better the accuracy of the reconstructed 3D point cloud approaches the original. In addition, the lower the number of FLOPs, the less memory is required for the deep learning network. Therefore, the CD, EMD, and FLOPs performance evaluation results of the proposed method showed about 27% improvement in memory and 6.3% in terms of accuracy compared to the methods in other papers, demonstrating objective performance.

• Tunnel and Underground Space
• /
• v.24 no.6
• /
• pp.430-439
• /
• 2014

This study developed a simulation program for truck-loader haulage systems in an underground mine. A limestone underground mine in Korea was selected as a study area and investigated to design the simulation algorithm for truck-loader haulage systems. GPSS/H simulation language was utilized to develop the simulation program. Simulations were conducted to analyze the optimal number of haulage trucks dispatched in the 540 ML loading point by using the developed program. The simulation results showed that 8 trucks can maximize the daily production (2,076 ton). The real production (1,850 ton/day) of limestone ores was very similar to the simulated one (1,850.35 ton/day) when considers 7 trucks dispatched in the 540 ML loading point. In addition, average waiting time at loader were similar (waiting time by time study : 1.39 min, simulated waiting time : 1.35 min).

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.542-550
• /
• 2007

A geometry modification is one of main keys in achieving a successful optimization. The optimized hull form generated from the geometry modification should be a realistic, faired form from the ship manufacturing point of view. This paper presents a practical hull optimization procedure using a parametric modification function. In the parametric modification function method, the initial ship geometry was easily deformed according to the variations of design parameters. For example, bulbous bow can be modified with several parameters such as bulb area, bulb length, bulb height etc. Design parameters are considered as design variables to modify hull form, which can reduce the number of design variables in optimization process and hence reduce its time cost. To verify the use of the parametric modification function, optimization for KCS was performed at its design speed (FN=0.26) and the wave making resistance is calculated using a well proven potential code with fully nonlinear free surface conditions. The design variables used are key design parameters such as Cp curve, section shape and bulb shape. This study shows that the hull form optimized by the parametric modification function brings 7.6% reduction in wave making resistance. In addition, for verification and comparison purpose, a direct geometry variation method using a bell-shape modification function is used. It is shown that the optimal hull form generated by the bell-shaped modification function is very similar to that produced by the parametric modification function. However, the total running time of the parametric optimization is six times shorter than that of the bell shape modification method, showing the effectiveness and practicalness from a designer point of view in ship yards.