• 제목/요약/키워드: NOx formation characteristics

검색결과 122건 처리시간 0.027초

디젤 예혼합 압축착화 엔진에서 EGR 및 수소농후가스의 영향 (The Effects of EGR and Hydrogen Enriched Gas on Diesel HCCI Engine)

  • 박철웅;조준호;오승묵
    • 한국자동차공학회논문집
    • /
    • 제19권1호
    • /
    • pp.1-8
    • /
    • 2011
  • In recent years, there has been an interest in early-injection diesel engines as it has the potential of achieving a more homogeneous and leaner mixture close to TDC compared to standard diesel engine. The more homogeneous mixture may result in reduced NOx and soot emissions and higher efficiency in homogeneous charge compression ignition engines. While earlier studies have shown that a reduction in NOx emissions from HCCI engine is possible, there are some significant problems including the control of ignition timing and combustion rate. In order to investigate the effect of EGR and hydrogen enriched gas on combustion characteristics and emissions, an experiments with single cylinder CRDi engine were carried out concerning the formation of various premixed charge, which can achieved by early injection, EGR and hydrogen enriched gas. EGR was not effective to further reduce NOx and PM emissions. It was found that NOx emissions were decreased with an introduction of hydrogen enriched gas and an adequate diesel fuel amount.

토양 혼합여재를 이용한 질소산화물 제거특성 (Removal Characteristics of NOx Using a Mixed Soil-Biofilter)

  • 조기철;신은상;황경철;조일형;이내현;여현구
    • 환경위생공학
    • /
    • 제21권3호
    • /
    • pp.15-26
    • /
    • 2006
  • As traffic in city-centre around the world continues to increase, so levels of atmospheric pollutants continue to rise. High concentrations of NOx can have negative effects on human health, and we must find new ways to reduce their levels in the air we breathe. Nitrogen oxide gas (NOx), consisting of nitrogen monoxide (NO) and nitrogen dioxide $(NO_2)$ produced using $O_3$ oxidation, at a low concentration corresponding to that on roads as a result of exhaust from automobiles, was carried out to evaluate the removal characteristics of NOx through a laboratory-scale biofilter packed with soil as a packing material. A mixture media (yellow soil (30%): soil (40%): compost (10%): a used briquet (20%)) was applied. After about 1day of operation, the removal efficiency for $NO_2$ in all experiments with a constant condition ($25^{\circ}C$ and water humidity (60%)) was over 98%. The retention times of the section between phase I and phase II for formation and reduction of $NO_3$ NO and $NO_2$ on the initial $NO_3$ concentration was 50min $(O_3:195\;ppb),\;55min\;(O_3:925\;ppb),\;65min\;(O_3:1743\;ppb),\;70min\;(O_3:2616\;ppb),\;75min\;(O_3:3500\;ppb)$, respectively The soil biofilter system is a unique technology that purifies urban air by utilizing the natural processes that take place in the soil. Although some of the processes are quite complex, they can broadly be summarized as adsorption onto soil particles, dissolution into soil pore water, and biochemical.

와동과 상호작용하는 화염편에서의 오염물질 생성특성 (Pollutant Formation Characteristics in a Flamelet Interacting with a Vortex)

  • 오창보;이의주
    • 한국안전학회지
    • /
    • 제25권1호
    • /
    • pp.9-16
    • /
    • 2010
  • Flame structure of diffusion flame interacting with a single vortex was investigated with direct numerical simulation (DNS). A well-known counterflow diffusion flame was used as an initial flat flame and single vortices were made by issuing a high-velocity jet abruptly in fuel- and air-side. The variations in the maximum concentration of major species (CO and $CO_2$) and NOx (NO and $NO_2$) with the stoichiometric scalar dissipation rate were investigated. Unsteady effects in the species concentration variation of the flame interacting with a vortex were identified by comparing with that of steady flame. $NO_2$ formation characteristics of the flame interacting with a vortex were well understood by investigating the $HO_2$ formation. To enhance the prediction performance in the fire simulation, current turbulent combustion modelings are needed to be modified by adopting the unsteady effects in the species concentrations of diffusion flame interacting with a vortex.

석탄화력보일러에서 고수분탄 및 건조석탄 사용에 따른 연소 및 배기배출 특성에 대한 전산해석 연구 (Numerical Study on the Characteristics of Combustion and Emission in Pulverized Coal-fired Boiler for Using High Moisture Coal and Dry Coal)

  • 안석기;김강민;김규보;이시훈;전충환
    • 에너지공학
    • /
    • 제26권4호
    • /
    • pp.118-126
    • /
    • 2017
  • 본 연구에서는 석탄화력보일러에서 고수분탄 및 건조석탄 사용이 연소와 배기배출 특성에 미치는 영향에 대한 전산해석 연구를 수행하였다. 대상 보일러 설계 조건의 성능데이터를 기준으로 보일러 해석 모델 결과를 검증하였으며, 역청탄과 고수분탄 및 건조석탄을 혼소하는 조건에 대한 계산을 수행하였다. 고수분탄 혼소 비율이 높아질수록 가스 수직속도는 증가하였으며, 이는 연료의 노내 체류시간을 줄여 보일러 연소성에 영향을 미칠 것으로 판단된다. 건조석탄을 혼소할 경우 역청탄과 유사한 연소 및 배기배출 특성을 보였다. 고수분탄 혼소 비율이 높아질수록 수분영향에 의해 버너영역에서 연소반응 및 NOx 생성은 감소하였으며, OFA(Over-fire air) 이후에 가스온도와 NOx 생성이 높아지는 결과를 확인하였다.

관류보일러 연소실에서 비예혼합 VIStA 버너의 연소 특성 (Combustion Characteristics of Non-premixed VIStA Burner in Once-Through-Type Boiler)

  • 안준;김혁주;최규성
    • 대한기계학회논문집B
    • /
    • 제34권5호
    • /
    • pp.547-552
    • /
    • 2010
  • 본 연구에서는 VIStA(Vortex Inertial Staged Air) 버너를 개조하여 관류보일러에 적용하였다. 개조는 크게 2가지 부분에서 이루어 졌는데, 먼저 원형에서 채택한 예혼합 연소 방식을 사용상 편의와 안전을 위해 비예혼합방식으로 변경하였다. 연소 방식의 변경에 따라 공기 1차, 2차에 별도의 송풍기를 사용하던 공급 방식도 변경하여 본 연구에서는 하나의 송풍기로부터 공기를 공급받아 댐퍼를 통하여 1, 2차 연소실에 분할하여 공기를 공급하도록 하였다. 본 연구에서는 질소 산화물(NOx)의 생성을 억제하는 최적의 운전 조건을 찾기 위하여 전체 공기비 및 1, 2차 연소실로의 공기 분배 비율에 따른 NOx 생성 특성을 관찰하였다. 본 연구에서 산업용 보일러에 적용하기 위해 개조한 비예혼합 방식의 VIStA 버너를 설치한 결과, 기존의 일반 버너에 비해 균일한 화염을 얻었고 질소 산화물을 최대 20%까지 줄일 수 있는 것을 확인하였다.

가솔린 엔진에서 가솔린-암모니아 혼합 연료의 연소 및 배기 특성 (Combustion Characteristics and Exhaust Emissions in Spark-ignition Engine Using Gasoline-ammonia)

  • 유경현
    • 한국자동차공학회논문집
    • /
    • 제21권6호
    • /
    • pp.155-165
    • /
    • 2013
  • The effect of gaseous ammonia direct injection on the engine performance and exhaust emissions in gasoline-ammonia dual fueled spark-ignition engine was investigated in this study. Results show that based on the gasoline contribution engine power increases as the ammonia injection timing and duration is advanced and increased, respectively. However, as the initial amount of gasoline is increased the maximum power output contribution from ammonia is reduced. For gasoline-ammonia, the appropriate injection timing is found to range from 320 BTDC at low loads to 370 BTDC at high loads and the peak pressures are slightly lower than that for gasoline due to the slow flame speed of ammonia, resulting in the reduction of combustion efficiency. The brake specific energy consumption (BSEC) for gasoline-ammonia has little difference compared to the BSEC for gasoline only. Ammonia direct injection causes slight reduction of $CO_2$ and CO for all presented loads but significantly increases HC due to the low combustion efficiency of ammonia. Also, ammonia direct injection results in both increased ammonia and NOx in the exhaust due to formation of fuel NOx and ammonia slip.

순산소 미분탄 연소에서 화염전파와 NO 생성 특성 (Flame Propagation and NO Formation Characteristics in Oxy-fuel Pulverized Coal Combustion)

  • 문철언;최경민;김덕줄;김태형;서상일
    • 대한설비공학회:학술대회논문집
    • /
    • 대한설비공학회 2009년도 하계학술발표대회 논문집
    • /
    • pp.365-366
    • /
    • 2009
  • 미분탄 순산소 연소는 기존의 연소 방법과는 달리 산화제로 O2/CO2를 사용함으로써 NOx의 발생을 감소시킬 수 있으며, 고농도의 CO2를 쉽게 회수 할 수 있어 큰 주목을 받고 있다. NOx의 배출저감을 위한 기술로는 로 내에서의 재연소(reburning), 단계(staging) 연소등이 있으며, 후처리 NOx 저감기술로는 SCR, SNCR등이 있다. 그러나 이러한 기술들은 비용이 비싸다는 단점이 있으며, 미분탄 순산소 연소조건에서는 화염 안정성이 감소하는 문제점이 있다. 따라서 본 연구에서는 화염의 안정성과 밀접한 관련을 가지는 화염전파속도에 대해 미분탄 순산소 연소에서 석탄 입자의 물성치와 주위 기체의 특성이 화염전파속도에 미치는 영향을 수치적 방법을 통하여 해석하였으며, NO 저감의 한 방법인 연소가스 재순환(Flue Gas Recirculation)에 따른 연소특성 및 NO 생성 메커니즘의 영향과 석탄을 가스화 시키는 방법에 따른 연료의 연소특성에 대해 해석하였다.

  • PDF

흡기관내로의 물 분사에 의한 디젤기관의 연소특성 (I) (The Combustion Characteristics of Diesel Engine by the Water Injection through the Intake Port (I))

  • 유경현;윤용진;오영택
    • 대한기계학회논문집B
    • /
    • 제26권12호
    • /
    • pp.1756-1762
    • /
    • 2002
  • To effectively meet current regulations on the exhaust emissions of diesel engine required to control the deterioration of air pollution in the whole world, this study is to investigate the effects of water induction through the air intake system on the characteristics of combustion and exhaust emissions in IDI diesel engine. A method fur supplying water through the air intake system to reduce the exhaust emissions has been considered with other methods such as water introduction in the form of water-in-fuel emulsion or water injection directly into the combustion chamber, but it has not been studied about the effects of water on the combustion concepts and the characteristics of exhaust emissions in detail until now. In this study, the formation of NOx was significantly suppressed by decreasing the gas peak temperature during the initial combustion process because the water play a role as a heat sink during evaporating in the combustion chamber, but the smoke was slightly increased by increasing water amount.

H2/Air 비예혼합화염의 화염신장율에 따른 NO 생성경로의 상세해석 (Detailed Analysis of NO Formation Routes with Strain Rate in H2/Air Nonpremixed Flames)

  • 김종현;황철홍;이창언
    • 대한기계학회논문집B
    • /
    • 제32권8호
    • /
    • pp.604-611
    • /
    • 2008
  • Detailed analysis of NO formation routes and its contributions with strain rate in hydrogen/air flames were numerically investigated. LiG detailed reaction mechanism has been used for calculation, which is compared with experimental data in literature. It shows good agreement with experiment for both temperature and NO mole fraction. Three routes have been found important for NO formation in hydrogen flames. These are the Thermal route, NNH route and $N_2O$ route. Strain rate were varied to discuss the $EI_{NO}$ reduction trend in hydrogen nonpremixed flames, which are analyzed by each NO formation routes. As a result, as the strain rate increase, $EI_{NO}$ decrease sharply until strain rate $100s^{-1}$ and decrease slowly until strain rate $310s^{-1}$ again, after that $EI_{NO}$ keeps nearly constant. It can be identified that $EI_{NO}$ trend with the strain rate is well explained by a combination of variation of production rate of above Thermal, NNH and $N_2O$ route. Also result of Thermal-Mech. that includes only thermal NO reaction is compared with those of Full-Mech. As a result, It can be identified that there was difference between the two results of calculation. It is attributed to result that Thermal-mech did not consider contributions of NNH and $N_2O$ route. From these result, we can conclude that NOx emission characteristics of hydrogen nonpremixed flames should consider contributions of above three routes simultaneously.

예혼합 압축착화 엔진의 혼합기 형성 및 연소 특성에 관한 연구 (A Study on the Characteristics of Mixture Formation and Combustion in the Premixed Charge Compression Ignition Engine)

  • 김형민;류재덕;이기형
    • 한국자동차공학회논문집
    • /
    • 제14권3호
    • /
    • pp.1-9
    • /
    • 2006
  • Recently, there has been an interest in premixed diesel engines as it has the potential of achieving a more homogeneous and leaner mixture close to TDC compared to conventional diesel engines. Because this concept reduced NOx and smoke emissions simultaneously. Early studies are shown that in a HCCI(Homogeneous Charge Compression Ignition) engine, the fuel injection timing and intake air temperature affect the mixture formation. The purpose of this study is to investigate characteristics of combustion and mixture formation according to injection timing and intake air temperature in a common rail direct injection type HCCI engine using an early injection method called the PCCI(Premixed Charge Compression Ignition). From this study, we found that the fuel injection timing and intake air temperature affect the mixture formation and in turn affects combustion in the PCCI engine.