• Journal of ILASS-Korea
• /
• v.23 no.3
• /
• pp.128-135
• /
• 2018

In this study, the following conclusions could be obtained from the analysis of emissions contribution rates and features for contaminated emissions by 13,456 gasoline vehicles passed in the vehicle load test (ASM-idle) under the inspection year 2013 to 2017. It was confirmed that the contamination of the CO, HC, NOx by the displacement is reduced on over 3L engine. As a result of comparing the exhaust gas in the low speed idle mode and the AS2525 mode, the exhaust gas in the low speed idle mode was measured high. It is estimated that if ISG function is applied, emissions from idle condition will be reduced. NOx emissions were reduced when the engine power was above 200HP. It has been confirmed that the amount of exhaust emissions are significantly reduced for vehicles manufactured after 2004. As a result of analyzing the exhaust gas according to the season, it is judged that there is a correlation between HC and NOx according to the ambient temperature. The concentration of exhaust emission in vehicles with high accumulated distance increases, which is considered to be the result of aging of the vehicle.

• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.122-127
• /
• 2006

The objective of this research is to determine generally applicable design principles for the development of Rapid mix burner. Details operating RMB(Rapid mix burner) is designed that thermal NOx and prompt NOx formation be reduced through control of low peak flame temperature, and nearly uniform flame temperature by rapid mixing at the ignition point. Results from RMB(Rapid mix burner) achieving lower than 43 ppm NOx emissions and nearly flame temperature uniform

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.12
• /
• pp.965-973
• /
• 2015

Recently, an emission test procedure using a portable emissions measurement system(PEMS) has received much attention as an effective means of controlling real driving emissions from light-duty diesel vehicles. The PEMS-based test procedure will be implemented from 2017 in Europe and Korea as a complementary test procedure for certification and regulation. In the present study, on-road NOx emissions were measured for four kinds of Euro 5 Korean light-duty diesel vehicles under real driving conditions, including urban, rural, and motorway test routes. The real driving emission characteristics were evaluated using both a moving averaging window(MAW) and the weighted emission method(WEM). The evaluated NOx emission results (under real driving conditions) from the MAW and WEM showed similar tendencies for the test vehicles and routes, while exceeding the certification emission limit by 1.8~8.5 and 2.0~10.6 times, respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.1
• /
• pp.25-32
• /
• 1999

This study was carried out to reduce NOx emissions from diesel engine and to investigate the variation of engine performance using the water injection. In this study the water was extracted from the exhaust gas and injected directly into the intake port with the inlet charge. The water condensing system operated as a closed system without any supplementary water supply. The experimental parameters such as the revolution the torque and the water injection rate are varied and the result from this experiment found the significant NOx reduction whereas the smoke emission increases as water/air ratio increases as the cases like the EGR. In spite of increasing the quantity of the water injection the engine output was slightly decreased and the specific fuel consumption was increased as was anticipated. Especially the system was founded to be effective on the reduction of the NOx emissions at the high load region relatively.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3085-3089
• /
• 2008

In order to reduce NOx and Soot emissions simultaneously, characteristics of diesel spray and combustion were investigated by numerical simulation with StarCD in this paper. This work focuses on effect of Spin Injection. A simulation model of combustion, spray and emissions is developed for heavy duty marine diesel engine application. Simulation is performed with change of spray angle between first and second directions at fixed engine speed, injection timing, injection duration and etc. The results show that Spin Spray Injection method can reduce NOx emission. And the results show that the 1st injection considerably interfere with 2nd injection characteristics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.37-43
• /
• 2014

Exhaust emissions were studied as a function of gasoline olefin composition in two vehicles-MPI and GDi engine equipped vehicles. Three different gasolines were tested which varied in olefin contents-12, 16 and 20 vol%. Exhaust emissions in two vehicles were affected by changes in gasoline olefin composition. Responses to changes in olefins were similar in both vehicles : reducing olefins lowered emissions of NOx and CO. Measured exhaust emissions included total hydrocarbons (THC), oxides of nitrogen (NOx), carbon monooxide(CO), carbon dioxide($CO_2$), formaldehyde, benzene, toluene, xylene, 1,3-butadiene and acetylene.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.4
• /
• pp.421-426
• /
• 2000

A study on the combustion and exhaust emissions characteristics of diesel engine with various suction air humidity is performed experimentally. In this paper, suction air humidity is changed from RH 50% to RH 90%, the experiments are performed at engine speed 1800rpm, and main measured parameters are cylinder pressure, fuel consumption rate, CO, HC, NOx and Soot emissions etc. Increase of suction air humidity from RH 50% to RH 90% does not effect specific fuel consumption, decreases maximum pressure in cylinder, ratio of maximum pressure rise and net heat release, and delays ignition timing. Also, that increases CO and HC emissions, decreases NOx emissions, but does not constant in changing tendency on emission.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3007-3012
• /
• 2008

Multidimensional simulation has been carried out to be clear the role of initial combustion in a marine diesel engines on reduction of NOx and soot emissions by different pilot injection condition. Pilot injection can shorten the ignition delay, thus it reduces the premixed combustion phase. Since most NOx is formed during premixed combustion, pilot injections is one of reliable strategies to reduce the NOx. The formation of NOx consists of that formed by pilot injection and that formed by main injection. The result explains that 25-3-75 among the pilot injection conditions is effective to reduce the NOx, due to optimal combination pilot injection with main injection. The purpose of this study is to explain the characteristics of combustion with pilot injection of the marine diesel engine on reduction of exhaust emissions by examining the combustion process in a cylinder and to explore the formation mechanism of NOx between pilot injection and main injection.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.10
• /
• pp.33-39
• /
• 2019

The improvement of emissions, fuel economy, and combustion noise is a primary target in the development of heavy-duty diesel engines. Multiple injection has been introduced as one of the most promising strategies for this goal. In this research, various multiple injection methods were applied to achieve the optimal strategy in terms of emissions, fuel economy, and combustion noise. In the case of one pilot injection, the smoke emission deteriorated, while the NOx emission was reduced. In the case of 2 pilot injections, the NOx and smoke emissions were reduced by 73% and 84%, respectively. In this case, the combustion noise was analyzed with the maximum pressure-rise rate, and the fuel economy was evaluated with the help of the indicated specific fuel consumption. A 15%:15% 2-pilot injection strategy accomplished improvements of 32.9% for NOx, 60.4% for smoke, 1.95% for fuel consumption, and 19.4% for combustion noise compared to the case of single injection. Based on the data, an optimal injection strategy will be developed for a greater operating range in future work.

• Journal of Energy Engineering
• /
• v.22 no.2
• /
• pp.136-140
• /
• 2013

The stringent emission norms cannot be met through engine design and exhaust after treatment alone. Use of oxygenated fuel like biodiesel as a alternative to diesel may be the best way to reduce emissions today. In this study, Diesel fuel and pure biodiesel (mahua oil) were tested on a single cylinder naturally-aspirated direct-injection diesel engine. The study aims to investigate the effects of the mahua oil biodiesel on existing diesel engine emissions. The effect of test fuels on engine emissions like CO, HC, $CO_2$, NOx and smoke emissions was investigated with respect to the load on engine. Smoke opacity of Diesel engine was lower in case of biodiesel of mahua oil as compare to mineral diesel. NOx emissions was little higher during the whole range of loading, which is a typical characteristic of biodiesel. However the increments are within in the narrow range. $CO_2$ emissions was bit higher which is the indication of better combustion due to presence of rich oxygen in the mixture, it results in the low values of CO and HC during the whole range of experiments. Thus considering environmental norms most of the engine emissions, it can be concluded and biodiesel derived from mahua oil could be used in a conventional diesel engine without any modification.