• The Journal of Korea Robotics Society
• /
• v.17 no.1
• /
• pp.93-101
• /
• 2022

Bioheavy oil, which is expanding its range of use as an alternative fuel to reduce environmental pollutant emissions, has a lot of difficulty in combustion due to its low emission of pollutants such as nitrogen oxide (NOx) and sulfur oxide (SOx), while its low dissipation and high oxygen content in fuel. many studies have been conducted on change in characteristics by mixing rate combustion characteristics and combustion reactions, but there have been no specific and effective studies on the composition of control system, optimization of control, development of logic for mixing and burning, minimizing environmental pollutantants discharge. In this study, we intend to consider systemmatic and empirical considerations on the composition, logic development, solve the problem of manual switching of bioler master due to excessive oxygen content and tuning of the control system for optimal combustion of bioheavy oil.

• Journal of Navigation and Port Research
• /
• v.40 no.4
• /
• pp.173-181
• /
• 2016

From 2016, controls on reduction of NOx and SOx emissions from the vessels that are operated in the emission control area were tightened. The selectivity catalytic reduction system of the denitrification equipment which NOx among the above controlled materials is very effective and used commercially very much. But it has the disadvantage that CSR is activated at high temperatures. Therefore, the SCR and SCR activation instrument that can react even at low temperatures by using micro-nano bubbles so that the above problems can be minimized were developed. And the computational fluid dynamics technique was used by ANSYS-CFX package to prepare the plan that improves the SCR system's efficiency. Simulation for the viscous flow analysis of the SCR system was executed by applying the Navier-Stokes equation to it as a governing equation. For the SCR system's shape, 3D modeling was done by using CATIA V5. SCR jet nozzle's position was checked by changing it to the intervals of 1/3, 1/2, and 2/3 from the inlet of the vent pipe to compare the SCR system's efficiency. And the number of nozzles was compared and analyzed by simulating 4, 6, and 8 holes to check an effect of the number on the SCR system's efficiency. The simulation result has found that the closer nozzles are to the inlet of the vent pipe and the more nozzles are, the more efficiency is improved.

• Journal of the Economic Geographical Society of Korea
• /
• v.13 no.3
• /
• pp.398-415
• /
• 2010

The purpose of this paper is to grasp levels of cost burden in pollution treatment by measuring efficiencies and shadow prices by pollutants in Korean cities. The efficiencies and shadow prices of pollutants will be compared for cities divided by Seoul metropolitan area and non-Seoul metropolitan area. Annual shadow prices of NOx, SOx, and PM10 emissions in the cities of Seoul metropolitan area are 0.846, 0.318, 0.816, respectively for 1999-2005. The annual shadow prices in the cities of Non-Seoul metropolitan area are 0.848, 0.272, and 0.789, respectively over the same periods. The shadow prices of SOx showed similar levels between two areas but those of NOx and PM10 of cities in Seoul metropolitan area were higher. NOx emission quantities of both areas have similar increasing patterns because the NOx has mainly increased with augmentation of transportation regardless of Seoul metropolitan and non-Seoul metropolitan areas. It seems that the reason the shadow prices of two pollutants for the cities of Seoul metropolitan area are higher, is because environmental regulation is stronger in the cities of Seoul metropolitan area, the cities of Seoul metropolitan relatively show higher quantities of pollution reduction under given desirable outputs, and generally have industrial sectors with small pollution emission. In the future we need to reduce pollutants in the various respects such as adjustment of overall industry structure, energy consumption pattern, and reviews of arrangement of living space for the cities located on the downward-sloping segment of production frontier.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.2
• /
• pp.75-83
• /
• 2014

The present study estimated nitrogen budget of South Korea including nitrogen oxides (NOx) in 2011. Emission sources of NOx were calculated with the higher contributors, such as vehicles, businesses, power plants, based on the IPCC and EPA reports. Moreover, nitrogen budget was separated for city, agriculture livestock and forest. Input and output were chemical fertilizer, crop uptake, fixation, irrigation, compost, leaching, volatilization, imported food, denitrification, runoff, and so on. Annual nitrogen input were 1,692,650 ton/yr and output were 837,739 ton/yr which were increased from 2010 budget. In 2011, NOx emissions by vehicles, power plants, and businesses were 308,207 ton/yr, 601,437 ton/yr, and 469,946 ton/yr, respectively. Including nitrogen oxide, total nitrogen input and output in 2011 was calculated as 5,652,366 ton/yr and 1,425,371 ton/yr, respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1421-1432
• /
• 2018

Water soluble oil was obtained from the pyrolysis of coconut waste as a biomass at $600^{\circ}C$. It was studied that the combustion characteristics of bio-emulsion fuel by mixing and emulsifying 15~20% of water soluble oil which obtained from pyrolysis of coconut waste as a biomass and MDO(marine diesel oil) as a marine fuel. Engine dynamometer was used for detecting emissions, temperature, and power. The temperature of combustion chamber was decreased because the moisture in bio-emulsion fuel deprived of heat of evaporation in combustion chamber. While combustion, micro-explosion took place in the combustion chamber by water in the bio-emulsion fuel, MDO fuel scattered to micro particles and it caused to smoke reduction. The temperature reduction of combustion chamber by using bio-emulsion fuel reduced the NOx emission. The increasing of bio-oil content caused increasing water content in bio-emulsion fuel so total calorific value was reduced. So the characteristics of power was decreased in proportion to using the increasing amount of bio-emulsion fuel. Heavy oil as a marine fuel exhausts a lot of smoke and NOx. We expect that we can reduce the exhaust gas of marine engine such as smoke and NOx by using of bio-emulsion fuel as a marine fuel.

• Journal of Korea Port Economic Association
• /
• v.35 no.2
• /
• pp.93-108
• /
• 2019

Recently, air pollution from the marine ports has become a serious issue all over the world. Because marine trade accounts for 99.7% of Korea's trade, efforts are required to recognize the level of port pollution and establish environmental policies. This study estimates air pollution emitted during the berthing process in the Gwangyang and Ulsan ports. Data on ship activity and characteristics are collected and reasonable methodologies and factors from EEA and EPA are adopted. The results show that 253.09 tons of CO, 1986.61 tons of NOx, 684.01 tons of SOx, 47.88 tons of $PM_{10}$, and 44.69 tons of $PM_{2.5}$ are emitted at the Gwangyang port. Further, the Ulsan port emitted 212.28 tons of CO, 1712.54 tons of NOx, 573.72 tons of SOx, 40.16 tons of $PM_{10}$, and 37.48 tons of $PM_{2.5}$. A stage-by-stage plan for installing AMP infrastructure is suggested as part of a green port policy. This research provides the current pollution status and contributes guidelines for the direction of future policy.

• Journal of the Korean Institute of Gas
• /
• v.26 no.3
• /
• pp.45-53
• /
• 2022

In order to improve the emission of diesel engines, natural gas-diesel dual fuel combustion compression ignition engines are in the spotlight. In particular, a reactivity controlled compression ignition (RCCI) combustion strategy is investigated comprehensively due to its possibility to improve both efficiency and emissions. With advanced diesel direct injection timing earlier than TDC, it achieves spontaneous reaction with overall lean mixture from a homogeneous mixture in the entire cylinder area, reducing nitrogen oxides (NOx) and particulate matter (PM) and improving braking heat efficiency at the same time. However, there is a disadvantage in that the amount of incomplete combustion increases in a low load region with a relatively small amount of fuel-air. To solve this, sensitive control according to the diesel injection timing and fuel ratio is required. In this study, experiments were conducted to improve efficiency and exhaust emissions of the natural gas-diesel dual fuel engine at low load, and evaluate combustion stability according to the diesel injection timing at the operation point for power generation. A 6 L-class commercial diesel engine was used for the experiment which was conducted under a 50% load range (~50 kW) at 1,800 rpm. Two injectors with different spray patterns were applied to the experiment, and the fraction of natural gas and diesel injection timing were selected as main parameters. Based on the experimental results, it was confirmed that the brake thermal efficiency increased by up to 1.3%p in the modified injector with the narrow-angle injection added. In addition, the spray pattern of the modified injector was suitable for premixed combustion, increasing operable range in consideration of combustion instability, torque reduction, and emissions level under Tier-V level (0.4 g/kWh for NOx).

• Journal of the Korean Institute of Gas
• /
• v.27 no.3
• /
• pp.52-58
• /
• 2023

With the increasing awareness of the importance of carbon neutrality in response to global climate change, the utilization of hydrogen as a carbon-free fuel source is also growing. Hydrogen is commonly used in fuel cells (FC), but it can also be utilized in internal combustion engines (ICE) that are based on combustion. Particularly, ICEs that already have established infrastructure for production and supply can greatly contribute to the expansion of hydrogen energy utilization when it becomes difficult to rely solely on fuel cells or expand their infrastructure. However, a disadvantage of utilizing hydrogen through combustion is the potential generation of nitrogen oxides (NOx), which are harmful emissions formed when nitrogen in the air reacts with oxygen at high temperatures. In particular, for the EURO-7 exhaust regulation, which includes cold start operation, efforts to reduce exhaust emissions during the warm-up process are required. Therefore, in this study, the characteristics of nitrogen oxides and fuel consumption were investigated during the warm-up process of cooling water from room temperature to 88℃ using a 2-liter direct injection spark ignition (SI) engine fueled with hydrogen. One advantage of hydrogen, compared to conventional fuels like gasoline, natural gas, and liquefied petroleum gas (LPG), is its wide flammable range, which allows for sparser control of the excessive air ratio. In this study, the excessive air ratio was varied as 1.6/1.8/2.0 during the warm-up process, and the results were analyzed. The experimental results show that as the excessive air ratio becomes sparser during warm-up, the emission of nitrogen oxides per unit time decreases, and the thermal efficiency relatively increases. However, as the time required to reach the final temperature becomes longer, the cumulative emissions and fuel consumption may worsen.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.2
• /
• pp.165-171
• /
• 2010

The Homogeneous Charge Compression Ignition (HCCI) engine concept allows for both NOx and particulate matter to be reduced simultaneously, and it is a promising way to meet the next environmental challenges. Unfortunately, HCCI combustion often increases CO and HC emissions. The development of oxidation catalyst (OC) requires high conversion efficiency for CO and HC at low temperature. Conventional oxidation catalyst technologies may not be able to convert these emissions because of the saturation of active catalytic sites. The OC used in this study was 600 cpsi cordierite. Three kinds of OC with different amounts of Pt and Pd were used. The influence of the space velocity (SV), $H_2O$ and $O_2$ concentration was also studied. All types of OCs were found to have over 90% CO conversion efficiencies at $170^{\circ}C$. When in the presence of water vapor, CO conversion was increased, but $C_3H_8$ conversion was decreased. The performance of the OC was not influenced by initial the HC concentration. The 2Pt/Pd catalyst was better in terms of thermal aging than the Pt-only catalyst. The $LOT_{50}$ of both fresh and aged OC was increased with increasing SV and with the presence of $H_2O$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.3
• /
• pp.221-228
• /
• 2013

An experimental study was carried out to investigate the effects of the injection timing on the spray and combustion characteristics in a spray-guided direct-injection spark-ignition (DISI) engine under lean stratified operation. An in-cylinder pressure analysis, exhaust emissions measurement, and visualization of the spray and combustion were employed in this study. The combustion in a stratified DISI engine was found to have both lean premixed and diffusion controlled flame combustion characteristics. The injection timing condition corresponding to the stratified mixture characteristics was verified to be a dominant factor for these flame characteristics. For the early injection timing, a non-luminous blue flame and low combustion efficiency were observed as a result of the lean homogeneous mixture formation. On the other hand, a luminous sooting flame was shown at the late injection timing because of an under-mixed mixture formation. In addition, the smoke emission and incomplete combustion products were increased at the late injection timing as a result of the increased locally rich area. On the other hand, the NOx emissions decreased and IMEP increased as the injection timing retarded. The combustion phasing produced by the injection timing was verified as the reason for this observation.