• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.18-28
• /
• 2007

Three diesel engines were fueled with BDF 20, a blend of 80% diesel fuel and 20% biodiesel fuel by volume, and run in excess of 200 h to evaluate their combustion characteristics and durability. The engines used for this study were a 4-cylinder 2476-cc displacement IDI diesel engine(Engine 1), a 4-cylinder l732-cc displacement IDI diesel engine(Engine 2), and a single cylinder 673-cc displacement DI diesel engine(Engine 3). Engine dynamometer testing was performed on each engine at regularly scheduled intervals to monitor the performance and exhaust emissions, which were sampled at 1h intervals for analysis, The peak combustion pressure with BDF 20 increased in Engines 1 and 3 over that measured when burning pure diesel fuel, but that in Engine 2 remained constant. Combustion parameters, such as the maximum combustion pressure and corresponding crank angle, did not change over the long-term dynamometer testing. The BSFC with BDF 20 in Engine 1 was less than that measured with pure diesel fuel. The amount of smoke produced with BDF 20 was less for all engines ; the greatest reduction was observed for Engine 3. The NOx emissions were lower in the IDI engines than the DI engine. The traditional trade-off between smoke and NOx emissions was maintained for BDF 20 fuel for Engines 1 and 3. There was not a big difference in the $CO_2\;and\;O_2$ emissions for BDF 20, as compared to pure diesel fuel, but more $CO_2$ was exhausted by Engine 1 than by Engines 2 or 3 and less $O_2$ was exhausted by Engine 1 than by Engines 2 or 3. The engine parts remained clean, except for some carbon attached to the area surrounding the nozzle hole of the DI diesel engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.162-170
• /
• 2007

Currently, due to the serious world-wide air pollution by substances emitted from vehicles, emission control is enforced more firmly and it is expected that the regulation requirements for emission will become more severe. Anew concept combustion technology that can reduce the NOx and PM in relation to combustion is urgently required. Due to such social requirement, technologically advanced countries are making efforts to develop an environment-friendly vehicle engine at the nation-wide level in order to respond to the reinforced emission control. As a core combustion technology among new combustion technologies for the next generation engine, the homogeneous charge compression ignition (HCCI) is expanding its application range by adopting multiple combustion mode, catalyst, direct fuel injection and partially premixed combustion. This study used a 2-staged injection method in order to apply the HCCI combustion method without significantly altering engine specifications in the aspect of multiple combustion mode and practicality by referring to the results of studies on the HCCI engine. And it is investigated that the effects of the engine rpm and load(or A/F) to emission characteristics.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.5
• /
• pp.724-732
• /
• 2002

Although the demands for diesel engine is increased, our world is faced with very serious problems related to the air pollution due to the exhaust emissions of the diesel engine. In this study, the potential possibility of oxygenated fuel such as Methyl tertiary butyl ether (MTBE) was investigated for the sake of exhausted smoke reduction from diesel engine. MTBE has been used as a fuel additive blended into unleaded gasoline to improve octane number, but the study of application for diesel engine was incomplete. Because MTBE includes oxygen content approximately 18%, it is a kind of oxygenated fuel that the smoke emission of MTBE is reduced remarkably compared with commercial diesel fuel, that is, it can supply oxygen component sufficiently at high load and speed in diesel engine. But, the NOx emission of MTBE blended fuel is increased compared with commercial diesel fuel. And. it was tried to analyze not only total hydrocarbon but individual hydrocarbon components from $C_1$to $C_{6}$ in exhaust gas using gas chromatography to seek the reason for remarkable reduction of smoke emission. The results of this study show three conclusions. 1. The smoke omission of the MTBE blended fuel is lower than that of the diesel fuel at all experimental region in direct injection diesel engine. 2. Individual hydrocarbons(C$_1$~ $C_{6}$) as well as total hydrocarbon of oxygenated fuel are reduced remarkably compared with diesel fuel. 3. Smoke emission from diesel engines was strongly depended on oxygen content in fuel regardless of operating condition.

• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.267-274
• /
• 2006

Greenhouse gas reduction will be highlighted as the most pending question in the cement industry in future because the production of Portland cement not only consumes limestone, clay, coal, and electricity, but also release waste gases such as $CO_2,\;SO_3$, and NOX, which can contribute to the greenhouse effect and acid rain. To meet the increase of cement demand and simultaneously comply with the Kyoto Protocol, cement that gives less $CO_2$ discharge should be urgently developed. This study aims to manufacture non-sintering cement(NSC) by adding phosphogypsum(PG) and waste lime(WL) to granulated blast furnace slag(GBFS) as sulfate and alkali activators. This study also Investigates the hydration reaction of NSC through analysis of scanning electron microscopy(SEM), X-ray diffraction(XRD), differential thermal analysis(DTA), and pH. Results obtained from analysis of the hydrate have shown that the glassy films of GBFS are destroyed by the activation of alkali and sulfate, ions eluted from the inside of GBFS react with PG and produce ettringite, and consequently the remaining component in GBFS slowly produced C-5-H(I) gel. Here, PG is considered not only to play the role of simple activator, but also to work as a binder reacting with GBFS.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.6
• /
• pp.611-616
• /
• 2013

Many researches have been carried out consistently for the green ship owing to its economic increasement, efficiency and convenience. One of them is an electronic controlled marine diesel engine. However, we are suffered from dissemination of above engine, due to its anxiety about safety and reliability. In order to solve these problems in this study, emission characteristics test of main propulsive two-stroke diesel engine, equipped both electronic control and cam drive fuel injection systems, has been performed and evaluated under the various load conditions. From the test results, we have confirmed that exhaust gas emission characteristics of the electronic control system is similar to the cam drive system in eco-mode operation, but NOx in emission mode has been decreased 100ppm or more in full load condition. HC emission from the electronic control system is decreased 10~20ppm at 50% load, and 35~40ppm at 25% load in comparison to cam drive system. In fuel consumption, it is considered that 7g/kWh is decreased than the value of cam drive system at 700bar of injection pressure, which is 200bar higher than cam drive system.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.46-54
• /
• 1986

Driving pattern of gasoline passenger car was measured and analyzed at some areas(6urban area routes, 4 radial routes, 4 circular routes)in Seoul city. Measured items were vehicle speed, engine speed, intake manifold vacuum, and fuel consumption. Driving pattern data were reappearanced with engine dynamometer. Results of this investigation might be summarized as below; 1. When we compared urban area route with radial or circular route in rush hour, it was found that the average vehicle speed was measured to be lower about 25% and fuel consumption to be higher about 12% in urban area route. 2. Average vehicle speed was measured to be higher about 30% and driving resistance output to be higher about 25% in non-rush hour, but average fuel economy was increased a little. 3. On the bases of average fuel economy and characteristics of exhaust emissions, optimum driving vehicle speed was found about 60 km/h in the 4th(top)and about 40km/h in the 3rd in driving of experimental engine. 4. Idling frequency and exhaust emissions of CO,HC were related to idling closely. But exhaust emission of NOx, which had nothing to do with idling frequency, had relation to acceleration time ratio.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.115-122
• /
• 2006

To evaluate the durability characteristics of in-direct injection diesel engine using BDF 20(a blend of 20% biodiesel fuel and 80% diesel fuel in volume), an IDI diesel engine used to commercial vehicle was operated on BDF 20 for 300 hours. Engine dynamometer testing was completed at regularly scheduled intervals to investigate the combustion characteristics, engine performance and exhaust emissions. The engine performance and exhaust emissions were sampled at 1 hour interval for analysis. From the results, the combustion variations such as the combustion maximum pressure($P_{max}$) and the crank angle at which this maximum pressure occurs(${\Theta}_{Pmax}$) were not appeared during long-time dynamometer testing. Also, BSFC with BDF 20 resulted in lower than with diesel fuel. The peak pressure with BDF 20 was higher than that with diesel fuel due to the oxygen content in BDF. And, BDF 20 resulted in lower emissions of carbon monoxide, carbon dioxide, and smoke emissions with a little increase of oxides of nitrogen than diesel fuel. It was concluded that there was no unusual deterioration of the engine, or any unusual change in exhaust emissions during the durability test of an IDI diesel engine using BDF 20.

• Journal of Power System Engineering
• /
• v.17 no.6
• /
• pp.18-24
• /
• 2013

An experimental study was performed to investigate the characteristics of combustion pressure and exhaust emissions when the pilot injection timing and EGR rate were changed in a CRDI 4-cylinder diesel engine. The pilot injection timing and EGR rate have a significant impact on the combustion and emission characteristics of diesel engine. In this study, the pilot injection timing and EGR rate variation were conducted to 2000rpm of engine speed with torque 50Nm. Combustion pressure and heat release rate were decreased under high EGR rate conditions but increased under the pilot injection timing $20^{\circ}$(BTDC). IMEP and the maximum pressure in cylinder(Pmax) were decreased under the same injection timing with the increase of EGR rate. The NOx emission was decreased with increasing the EGR rate. On the other hand, in the same injection timing conditions, CO, HC, $CO_2$ emissions were increased with increasing the EGR rate.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.2
• /
• pp.57-62
• /
• 2000

The effect of exhaust gas recirculation(EGR) on the characteristics of exhaust gas emissions, and SFC are experimentally investigated by four-cylinder, four-cycle and direct injection marine diesel engine. In order to reduce the soot contents in the recirculated exhaust gas to intake system of the engines, a soot removal system of a cylinderical-type scrubber is specially designed and manufactured for the experimental system. (1) SFC is increased in downward convex curve style with increasing excess air ratio, it is increased with increasing EGR rate at the same excess air ratio. (2) NOx emission is reduced in downward convex curve style with increasing excess air ratio, it is reduced with increasing EGR rate at the same excess air ratio. (3) Soot emission is decreased in downward convex curve style with increasing excess air ratio, it is reduced with increasing EGR rate at the same excess air ratio. (4) CO emission is increased in nearly straight line style with increasing excess air ratio, it is increased with increasing EGR rate at the same excess air ratio. (5) HC emission is not constant tendency with increasing excess air ratio, it is increased with increasing EGR rate at the same excess air ratio.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.7-14
• /
• 2002

In order to reduce exhaust omissions of spark ignition engine, it is important not only to improve catalyst conversion efficiency but also to directly reduce engine out exhaust emissions, during cold starting and warm up process. Therefore many researchers have been attracted to develop an early fuel evaporator(EFE) by Introducing a ceramic heater fur a solution of engine out exhaust emissions in SI engine. But, the performance of the EFE in MPI engine to reduce the exhaust emissions and to improve the cold startability has not been clarified yet. The purpose of this study is to evaluate the feasibility of a glow plug far EFE. Impinging spray using heated and unheated glow plug helps the vaporization of the fuel and heat up the three way catalyst sufficiently. The amount of CO, and UHC is reduced overall. The amount of NOx is higher at the initial stage, but become lower as time goes on than without glow plug.