• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.287-292
• /
• 2008

The applicability of stainless steel type 316N to the PZR surge-lines of OPR1000 and APR1400 is investigated. So far, strainless steel type 347 has been used for the OPR1000 surge-lines. The degree of improvement in the leak-before-break(LBB) and component design margin is evaluated when stainless steel type 347 is substituted by type 316N. For the study, the tensile and J-R tests on type 316N and type 347 stainless steels were performed at 316 and the microstructure of both types was examined. Stainless steel type 316N shows the higher values on the stress-strain curves, J-R curves and stress intensity, Sm, compared to those of type 347. Therefore, stainless steel type 316N ensures the higher LBB and component design margins. As a result, this study shows that stainless steel type 316N could substitute type 347 for the surge-lines of OPR1000 and APR1400.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.4
• /
• pp.171-178
• /
• 2021

In the present study, we comparatively investigated the microstructures of two hot-rolled stainless steel clad plates; STS 304L - low carbon steel A516-70N and STS 316L - A516-70N. The STS 304L/A516-70N clad plate (Clad_304L_Ni) had a Ni-interlayer between stainless steel and carbon steel and a 90 ㎛ thick deformation band of unrecrystallized austenite grains on the stainless steel. The STS 316L/A516-70N clad plate (Clad_316L) had no interlayer and almost fully recrystallized austenite grains. Clad_304L_Ni exhibited the thinner a decarburized layer in carbon steel and a total carburized layer in stainless steel than Clad_316L. However, a severely carburized layer in stainless steel was thicker for Clad_304L_Ni than Clad_316L. Hardness profiles near the interface of clad plates matched well with microstructures at locations where the hardness values were measured.

• Journal of the Korean Chemical Society
• /
• v.39 no.11
• /
• pp.863-868
• /
• 1995

We have prepared microcolumns made of stainless steel tubing, glass-lined stainless steel tubing, and silica-lined stainless steel tubing and examined their performances comparatively. The length of columns was fixed as 30 cm, and the I.D.'s, either 1 mm or 0.5 mm. Octadecyl bonded silica paticles $(5\mu)$ were used as the stationary phases. p-Nitroaniline, N,N-dimethyl-o-nitro-p-toluidine,and ethylbenzene were used as the test solutes. The glass-lined or silica-lined stainless steel columns showed better performances than the plain stainless steel column did. The number of theoretical plates over 10,000 were obtained even for the 0.5 mm I.D. (30 cm long) column as long as the glass-lined stainless steel tubing was used.

• Journal of the Korean Society for Heat Treatment
• /
• v.23 no.5
• /
• pp.269-276
• /
• 2010

This study has been carried out to the low temperature plasma nitriding treatment on the mechanical properties of stainless steel at temperature range between $400^{\circ}C$ and $500^{\circ}C$. It was found that there was precipitated to free CrN matrix below $400^{\circ}C$ and there was precipitated S-phase of STS 316L, ${\varepsilon}$-phase of STS 409L and ${\alpha}N$-phase of STS 420J2. STS 316L has formed relatively abundant CrN phase and ${\gamma}^{\prime}-Fe_4N$ phase at $500^{\circ}C$, alternatively STS 409L and STS 420J2 were more deeply nitrided than STS 316L at $500^{\circ}C$.

• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.2
• /
• pp.78-82
• /
• 2003

Nitrided compound layer and diffusion layer structure were observed by SEM. The compound layer and the constituent of nitrided surface of STS 304, STS 316, STS 410 and SACM 645 steel were analysed using EMPA and XRD respectively. The depth of nitriding layer that is obtained from similar nitriding condition decrease in the order of SACM 645 > STS 410 > STS 316 > STS 304. Result of phase transformation of the nitrided at $550^{\circ}C$ by XRD analysis were as follows; The austenitic stainless steel was mainly consist of $Cr_2N$ accompanying with $Fe_4N$ and $Fe_{2-3}N$ phase and martensitic stainless steel was mainly consist of present $Fe_{2-3}N+Cr_2N$ phase, but SACM 645 steel was $Fe_{2-3}N$ phase present only.

• Korean Journal of Metals and Materials
• /
• v.49 no.10
• /
• pp.774-779
• /
• 2011

S-N fatigue behavior of cast 304 stainless steel was studied at 25, -50 and $-196^{\circ}C$ and at a stress ratio of -1 in uniaxial and bending loading condition. It was found that the resistance to S-N fatigue was greatly improved with decreasing testing temperature. The normalized S-N fatigue curves by tensile strength at three different testing temperatures matched each other, suggesting that tensile strength determines the S-N fatigue resistance of cast 304 stainless steel at low temperatures. The effects of different loading on the resistance to S-N fatigue of cast 304 stainless steel were quantified. The S-N fatigue curves at 25, -50 and $-196^{\circ}C$ were described by using Basquin's law the relationship between the S-N fatigue curve and the testing temperature was obtained by using a simple regression method.

• Journal of Surface Science and Engineering
• /
• v.26 no.6
• /
• pp.316-326
• /
• 1993

Adhesion and hardeness are the most important properties of a hard coated layer which is applied to wear-resistant devices. Zr/ZrN layer was deposited on tool steel(SKH9) and stainless steel(SUS304) by a re-active D.C. magnetron sputtering technique and their microhardness and adhesion strength were measured for the films processed by changing the partial pressures of $N_2$ gas (4~10$\times$$10^{-4}$mbar) and the substrate bias voltage(0~250V). The adhesion strength was evaluated by acoustic signals through the scratch-test with the incremental applied load. As the partial pressure of $N_2$ gas and the substrate bias voltage were increased, the adhesion strength of tool steel was observed to be stronger than that of the stainless steel. The adhesion strength was generally, observed to decrease with the same tendency regardless of the kinds of substrates. The adhesion strength of tool steel was increased more and more strongly than that of stainless steel as heat-treated temperature was increased. The strength of tool steel was appeared to be high adhesion strength at $400^{\circ}C$. From the failure mode of the film during the scratch adhesion test, the cohesive failure was observed to be obvious and the adhesive failure in a minor portion in the Zr/ZrN doublelayer regardless of the kinds of substrates.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.11
• /
• pp.3043-3047
• /
• 2009

Nitrogen solubility and nitride formation in liquid 304 Stainless steel has been measured by sampling method at various temperatures. Also values of thermodynamic functions are determined. Nitrogen solubility in molten 304 Stainless steel is increased with temperature and under the 1atm nitrogen atmosphere, titanium nitride is formed over 0.03wt%Ti in 304Stainless steel. Produced nitride is identified TiN by EDS analysis.

• Corrosion Science and Technology
• /
• v.3 no.5
• /
• pp.179-186
• /
• 2004

Recently the alloy development of duplex stainless steel has been done. On this study we studied the effect of the corrosion resistance according to the composition variety of C, Cr, N in the alloy elements of duplex stainless steel. materials which have below 0.1[mm/year] corrosion rate enable to use for corrosion-resisting materials, generally. On this experiment we inspected the effect of the composition variety of C, Cr, N in duplex stainless steel and the heat treatment, which the condition was the water quenching after the heat treatment for 1hr. The experiment was done on the basis of the ASTM G48A test, Critical pitting temperature(CPT), and ASTM G-61(Electrochemical tests for cyclic polarization).

• Bulletin of the Society of Naval Architects of Korea
• /
• v.8 no.2
• /
• pp.13-24
• /
• 1971

When friction welded material is actually used for parts of a machine, its fatigue strength is an important problem. Especially, there is no report which deals with mechanical properties of friction welded mild steel(S20C) and stainless steel(SUS27B). In this study are compared the compared the characteristics of such specimens as mild steel, stainless steel and welded material in the S-N diagram. And metallurgical consideration is directed to HAZ. The obtained results in these studies are summarized as follows; 1) The fatigue strength of welded material is slightly less than those of mild steel and stainless steel. 2) In the S-N diagram the knuckle point of welded material has larger number of cycle than that of stainless steel. 3) The fatigue notch factor of welded material is between those of mild steel and stainless steel. 4) mHv is the largest on the weld interface. It is larger before than after fatigue test on the stainless steel side. On the mild steel side it is the way around.