• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.6A
• /
• pp.426-437
• /
• 2012

This paper proposes an array antenna assisted Doppler spread compensator with dummy elements which are placed on either end of a monopole array for a digital terrestrial television broadcasting (DTTB) receiver. An array antenna assisted Doppler spread compensator, proposed previously, has a major drawback in performance degradation owing to mutual coupling effect among array elements. In order to solve the mutual coupling problem, dummy elements, placed on both sides of the monopole array mitigate performance degradation of a Doppler spread compensator arising from the mutual coupling among monopole array elements. Computer simulation results show that the dummy elements can reduce this performance degradation as well as expand the operating bandwidth of a Doppler spread compensator.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.6
• /
• pp.26-34
• /
• 2010

The mutual coupling of a pair of microstrip patch antennas on a finite grounded dielectric substrate is influenced by the diffracted field of surface waves from the edges of a substrate. The effective dielectric constant of a grounded dielectric substrate determines the distance between the antenna center and the edge of a substrate to obtain the minimum mutual coupling between a pair of microstrip patch antennas. The optimum substrate size with the minimum mutual coupling is easily calculated using the image method. The optimum substrate sizes using the linage method are in good agreement with the results obtained by the full wave simulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.157-157
• /
• 2000

In the fuzzy control for the multi-variable system, it is difficult to obtain the fuzzy rule. Therefore, the parallel structure of the independent single input-single output fuzzy controller using a pairing between the input and output variable is applied to the multi-variable system. The concept of relative gain matrix is used to obtain the input-output pairs. However, among the input/output variables which are not paired the interactive effects should be taken into account. these mutual coupling of variables affect the control performance. Therefore, for the control system with a strong coupling property, the control performance is sometimes lowered. In this paper, the effect of mutual coupling of variables is considered by tile introduction of a simple compensator. This compensator adjusts the degree of coupling between variables using a neural network. In this proposed neuro-fuzzy controller, the Neural network which is realized by back-propagation algorithm, adjusts the mutual coupling weight between variables.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1568-1572
• /
• 2004

This paper proposes a new online calibration algorithm for the array antenna system. As you know, the several previous calibration methods for the mutual coupling did not estimate but measure mutual coupling effect at the real or test-bed system directly. Therefore we suggest some idea to compensate the calibration errors due to mutual coupling effect and mismatch in cables and electronic modules without the off-line calibration. In this work, we can calibrate the array antenna system under the operation of the system using Independent Component Analysis(ICA). This is what is called an online calibration. As you know, the ICA method has permutation and scaling problems. However, we solve problems of the ICA method and apply it to the calibration of an array antenna. The method simultaneously estimates the DOA(Direction of Arrival) of the signals, and calibrates the array for that specific angle. The proposed algorithm is evaluated by computer simulation and its behavior is illustrated by a numerical example.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.8
• /
• pp.86-92
• /
• 2009

In order to minimize ac mutual coupling, the auxiliary electrode are located at a right angle in measuring ground impedance. In case that the measurement space is limited, the alternative method is employed. At that time, it is necessary to investigate the measurement errors due to ac mutual coupling and earth mutual resistance in measuring the ground impedances. 'This paper presents the measurement accuracy according to the location of the current and potential auxiliary electrodes in measuring ground impedance of vertically or horizontally buried ground electrode. The measurement errors due to ac mutual coupling were evaluated Consequently, the effect of ac mutual coupling on the measurement accuracy for horizontally buried ground electrode is greater than that for vertically buried ground electrode. Measurement errors due to ac mutual coupling is the largest when the current and potential auxiliary electrodes are located in parallel. The 61.8[%] rule is inappropriate in measuring ground measurement. Theoretically, in case that the angle between the current and potential auxiliary electrodes is 90$[^{\circ}]$, there is no ac mutual coupling. If it is not possible to route the current and potential auxiliary electrodes at a right angle with limitation of measurement space, the location of these electrodes with an obtuse angle is preferred to that with an acute angle in reducing the measurement errors due to ac mutual coupling.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.1
• /
• pp.65-72
• /
• 2009

For the evaluation of far-field performance by using the near-field probing on the base station dipole array antenna, the effects of mutual coupling depending on the heights between the array antenna with reflector and the probe were analyzed. When the height is varied in the near-field region, S parameters on the input ports of antenna and probe are measured and analyzed to decide the height for the minimum mutual coupling effect and the maximum probing efficiency. This height will be applicable to the near-field probing system design to achieve the precision far-field performance of a base station array antenna system.

• Proceedings of the KIEE Conference
• /
• 2003.11a
• /
• pp.71-74
• /
• 2003

Fall-of-potential method is used usually to measure the ground impedance of large scale grounding system exactly. Because the interlinked magnetic flux between closed loops to inject test current and to measure potential rise is existed in E-P-C straight line arrangement, mutual(or inductive) coupling influences greatly on the measurement correctness. Measurement errors produced from inductive coupling could be reduced by the arrangement methods of auxiliary electrodes. Right angle or P-E-C order arrangement methods were effective to reduce the inductive coupling and the decrease degree of measurement error was analysed as quantitative through an experiment.

• Journal of Satellite, Information and Communications
• /
• v.8 no.4
• /
• pp.37-42
• /
• 2013

In this paper, we propose a compensation method of a non-ideal antenna array and a computationally efficient estimation method of the direction of arrival (DOA) for the antenna array. For DOA estimation, an antenna array is essential. By using the phase difference between the output signals of antennas, we can derive the DOA. In practice, however, mutual coupling between the elements of an antenna array change the beam pattern of each element and degrade the performance of DOA estimation. In the proposed method, we first estimate the DOA for the mid-subarray of the array, where all elements undergo relatively same coupling effect. We use the estimation of signal parameters via rotational invariance techniques (ESPRIT) algorithm to estimate the DOA. Then, we expand the array based on the estimated DOA by compensating the coupling effect. Simulation results show that the proposed method is effective when jamming to noise power ratio (JNR)is relative low.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.3
• /
• pp.168-174
• /
• 2004

This paper describes a new fault location algorithm based on the voltage equation at the relaying point using 6-phase current for untransposed 765㎸ parallel transmission lines. The proposed method uses the voltage and current collected at only the local end. By means of 3-phase circuit analysis theory to compensate the mutual coupling effects between parallel lines, the fault location is derived. The fault distance is determined by solving the 2nd distance equation based on KVL(Kirchhoff's Voltage Law). Extensive simulation results using EMTP(Electromagnatic Transients Program) have verified that the error of the fault location achieved is up to 4.56(%) in untransposed parallel transmission lines.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.1349-1351
• /
• 2003

In this paper, theoretical channels model of Synthetic Aperture Radiometer is presented. Based on this model, how amplitude imbalance, phase imbalance and mutual coupling between the different channels effect brightness temperature image retrieving is analyzed. The computer simulation results are also presented to find out the cause of the along-track streaks usually appeared in the retrieved brightness temperature image. In addition, a new system calibration approach is introduced to solve this problem.