• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.3
• /
• pp.176- 184
• /
• 2010

A low-power inductorless 1:4 DEMUX and a 4:1 MUX for a 90 nm CMOS are presented. The DEMUX can be operated at a speed of 25 Gb/s with the power supply voltage of 1.05 V, and the power consumption is 8.9 mW. The area of the DEMUX core is $29\;{\times}\;40\;{\mu}m^2$. The operation speed of the 4:1 MUX is 13 Gb/s at a power supply voltage of 1.2 V, and the power consumption is 4 mW. The area of the MUX core is $30\;{\times}\;18\;{\mu}m^2$. The MUX/DEMUX mainly consists of differential pseudo-NMOS. In these MUX/DEMUX circuits, logic swing is nearly rail-to-rail, and a low $V_{dd}$. The component circuit is more scalable than a CML circuit, which is commonly used in a high-performance MUX/DEMUX. These MUX/DEMUX circuits are compatible with conventional CMOS logic circuit, and it can be directly connected to CMOS logic gates without logic level conversion. Furthermore, the circuits are useful for core-to-core interconnection in the system LSI or chip-to-chip communication within a multi-chip module, because of its low power, small footprint, and reasonable operation speed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.88-91
• /
• 2003

Tungsten is widely used as a plug for the multi-level interconnection structures. However, due to the poor adhesive properties of tungsten (W) on $SiO_2$ layer, the Ti/TiN barrier layer is usually deposited onto $SiO_2$ for increasing adhesion ability with W film. Generally, for the W-CMP (chemical mechanical polishing) process, the passivation layer on the tungsten surface during CMP plays an important role. In this paper, the effect of oxidants controlling the polishing selectivity of W/Ti/TiN layer were investigated. The alumina ($Al_2O_3$) abrasive containing slurry with $H_2O_2$ as the oxidizer, was studied. As our preliminary experimental results, very low removal rates were observed for the case of no-oxidant slurry. This low removal rate is only due to the mechanical abrasive force. However, for Ti and TiN with $H_2O_2$ oxidizer, different removal rate was observed. The removal mechanism of Ti during CMP is mainly due to mechanical abrasive, whereas for TiN, it is due to the formation of metastable soluble peroxide complex.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.33-36
• /
• 2003

Tungsten is widely used as a plug for the multi-level interconnection structures. However, due to the poor adhesive properties of tungsten (W) on $SiO_2$ layer, the Ti/TiN barrier layer is usually deposited onto $SiO_2$ for increasing adhesion ability with W film. Generally, for the W-CMP (chemical mechanical polishing) process, the passivation layer on the tungsten surface during CMP plays an important role. In this paper, the effect of oxidants controlling the polishing selectivity of W/Ti/TiN layer were investigated. The alumina $(Al_2O_3)$ abrasive containing slurry with 5 % $H_2O_2$ as the oxidizer, was studied. As our preliminary experimental results, very low removal rates were observed for the case of no-oxidant slurry. This low removal rate is only due to the mechanical abrasive force. However, for Ti and TiN with 5 % $H_2O_2$ oxidizer, different removal rate was observed. The removal mechanism of Ti during CMP is mainly due to mechanical abrasive, whereas for TiN, it is due to the formation of metastable soluble peroxide complex.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.136-139
• /
• 2003

Copper has attractive properties as a multi-level interconnection material due to lower resistivity and higher electromigration resistance as compared with Alumina and its alloy with Copper(0.5%). Among a variety of agents in Copper CMP slurry, $H_2O_2$ has commonly been used as the oxidizer However. $H_2O_2$ is so unstable that it requires stabilization to use as oxidizer Hence, stabilization of $H_2O_2$ is a vital process to get better yield in practical CMP process. In this article the stability of Hydrogen Peroxide as oxidizer of Copper CMP slurry has been investigated. When alumina abrasive was used, $\gamma$-particle Alumina C had a better stability than $\alpha$-particle abrasive. As adding KOH as pH buffering agent, $H_2O_2$ stability in slurry decreased. Urea hydrogen peroxide was used as oxidizer, an enhanced stability was gotten. When $H_3PO_4$ as $H_2O_2$ stabilizer was added, the decrease of $H_2O_2$ concentration in slurry became slower. Even though adding $H_2O_2$ in slurry after bead milling lead to better stability than in advance of bead milling, it had a lower dispersibility.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.4
• /
• pp.42-45
• /
• 2018

As The semiconductor decrease from 10 nanometer to 7 nanometer, It is suggested that "More than Moore" is needed to follow Moore's Law, which has been a guide for the semiconductor industry. Fan-Out Wafer Level Package(FOWLP) is considered as the key to "More than Moore" to lead the next generation in semiconductors, and the reasons are as follows. the fan-out WLP does not require a substrate, unlike conventional wire bonding and flip-chip bonding packages. As a result, the thickness of the package reduces, and the interconnection becomes shorter. It is easy to increase the number of I / Os and apply it to the multi-layered 3D package. However, FOWLP has many issues that need to be resolved in order for mass production to become feasible. One of the most critical problem is the warpage problem in a process. Due to the nature of the FOWLP structure, the RDL is wired to multiple layers. The warpage problem arises when a new RDL layer is created. It occurs because the solder ball reflow process is exposed to high temperatures for long periods of time, which may cause cracks inside the package. For this reason, we have studied warpage in the FOWLP structure using commercial simulation software through the implementation of the reflow process. Simulation was performed to reproduce the experiment of products of molding compound company. Young's modulus and poisson's ratio were found to be influenced by the order of influence of the factors affecting the distortion. We confirmed that the lower young's modulus and poisson's ratio, the lower warpage.