• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.4
• /
• pp.830-837
• /
• 2009

In this thesis, Multi-code/Multi-carrier CDMA(MC/MC CDMA) system which is combination of Multi-code CDMA and Multi-carrier CDMA is analyzed. This system is suitable fur multi-rate services that use multi-codes and high data rate transmission that employ multi-carriers. In addition, the MC/MC CDMA system is robust against frequency selective fading, is good for narrowband interference rejection, and has higher spectral efficiency. In this paper, The users are assigned OVSF codes as a spreading code according to their data rates and divides the active users having different representative code split into a number of groups for effective cancellation. At the receiver, The code grouping interference canceller performs cancellation between the groups. The proposed receiver does not require any information about interference users, such as code, data and amplitude, and has relatively low complexity. The results show the large improvement in performance that can be attained by cancellation scheme.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.4 s.97
• /
• pp.64-70
• /
• 1999

A new multi-beam optical system is presented on the grounds of tri-positioning systems in this paper. The system has been developed to improve the data transfer rate for the optical disk system. The actuating system is composed of a tracking and focusing actuating system basically and a newly developed beam rotating actuator. The beam rotating actuator is employed in a multi-beam optical system to trace more than one track simultaneously. The multi-beam optics is established through the optical simulation and several experimental trials. The differential phase tracking method is used in the tracking error signal detection based on the only one beam spot. We also analyze the characteristics of multi-beam optical system. The experimental result shows that the multi-beam positioning system has performance adequate to the multi-beam optical disk system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.1C
• /
• pp.34-42
• /
• 2007

The sphere decoder (SD) has recently been proposed to perform maximum likelihood (ML) decoding for multi-input multi-output systems. Employing a 'breadth-first' searching algorithm for closet points in a lattice, we propose a novel ML decoding scheme for multi-input multi-output systems. Simulation results show that the proposed scheme has the same bit error rate performance as the conventional ML decoders while allowing significantly lower computational burden than the SD.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.11
• /
• pp.2720-2736
• /
• 2013

Multi-view face detection has become an active area for research in the last few years. In this paper, a novel multi-view human face detection algorithm based on improved real Adaboost is presented. Real Adaboost algorithm is improved by weighted combination of weak classifiers and the approximately best combination coefficients are obtained. After that, we proved that the function of sample weight adjusting method and weak classifier training method is to guarantee the independence of weak classifiers. A coarse-to-fine hierarchical face detector combining the high efficiency of Haar feature with pose estimation phase based on our real Adaboost algorithm is proposed. This algorithm reduces training time cost greatly compared with classical real Adaboost algorithm. In addition, it speeds up strong classifier converging and reduces the number of weak classifiers. For frontal face detection, the experiments on MIT+CMU frontal face test set result a 96.4% correct rate with 528 false alarms; for multi-view face in real time test set result a 94.7 % correct rate. The experimental results verified the effectiveness of the proposed approach.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.4
• /
• pp.1579-1602
• /
• 2020

In the design of production system, buffer capacity allocation is a major step. Through polymorphism analysis of production capacity and production capability, this paper investigates a buffer allocation optimization problem aiming at the multi-stage production line including unreliable machines, which is concerned with maximizing the system theoretical production rate and minimizing the system state entropy for a certain amount of buffers simultaneously. Stochastic process analysis is employed to establish Markov models for repairable modular machines. Considering the complex structure, an improved vector UGF (Universal Generating Function) technique and composition operators are introduced to construct the system model. Then the measures to assess the system's multi-state reliability and structural complexity are given. Based on system theoretical production rate and system state entropy, mathematical model for buffer capacity optimization is built and optimized by a specific genetic algorithm. The feasibility and effectiveness of the proposed method is verified by an application of an engine head production line.

• Journal of Broadcast Engineering
• /
• v.20 no.6
• /
• pp.921-927
• /
• 2015

In this paper, we propose a novel design scheme for the operation of Decoded Picture Buffer (DPB) including reference picture re-ordering, marking process, and reference picture list construction to perform an efficient scalable multi-view video coding. Extensive simulations show that the proposed method can provide improved compression efficiency and improved video quality measured in terms of BD-Rate and BD-PSNR for the scalable multi-view video coding.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1853-1856
• /
• 2003

Multi-layer printed circuit board(PCB) is being used widely for the product with relatively complex circuits such as TV, VTR and FAX. With the rapid enlargement of electronic and IT industry, the hole machining technology on multi-layer PCB is increasingly required to improve. Thus, the micro drilling with ultrasonic vibration can be a good method for hole machining. Unlike conventional drilling, ultrasonic vibration applied drilling introduces less wear and fracture of not only tool but also internal surface of workpiece due to little cutting resistance, thus, machinability can be improved. The experiment is conducted through the comparison between the results of conventional drilling and ultrasonic micro drilling as well as among each results by the variation according to not only feed rate of drill but also amplitude and frequency of ultrasonic vibration. The multi-layer PCB consists of 6 layers and ${\Phi}$0.3 diameter drill was used. As a result, it was found that the state of internal surfaces of holes on multiple layer PCBs is improved by the application of ultrasonic vibration.

• Journal of Positioning, Navigation, and Timing
• /
• v.10 no.2
• /
• pp.103-111
• /
• 2021

A series of experiments have been carried out by using National Geographic Information Institute(NGII)'s Continuously Operating Reference Station (CORS) data with various strategies to analyze the impact of multi-GNSS measurements on baseline processing. The results of baseline processing were compared in terms of ambiguity fixing rate, precision, and hypothesis tests were conducted to confirm the statistical difference. The combination of multi-GNSS measurements has helped to improve ambiguity fixing rate, especially under harsh positioning environments. Combination of GPS, Galileo, BeiDou could get better precision than that of GPS, GLONASS, Galileo, and adding QZSS made the baseline solution's vertical component more precisely. The hypothesis tests have statistically confirmed that the inclusion of the multi-GNSS in the baseline processing enables not only to reduce field observation time length but also to enhance the solution's precision. However, it is of interest to notice that results of the baseline solution are dependent upon the software used. Hence, comprehensive studies should be performed shortly to derive the best practice to select the appropriate software.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.187-193
• /
• 2021

In order to solve the problem of false terrains caused by environmental interferences and tunneling effect in the conventional multi-beam seafloor terrain detection, this paper proposed a seafloor topography detection method based on fast two-dimensional (2D) Censored Mean Level Detector-statistics Constant False Alarm Rate (CMLD-CFAR) method. The proposed method uses s cross-sliding window. The target occlusion phenomenon that occurs in multi-target environments can be eliminated by censoring some of the large cells of the reference cells, while the remaining reference cells are used to calculate the local threshold. The conventional 2D CMLD-CFAR methods need to estimate the background clutter power level for every pixel, thus increasing the computational burden significantly. In order to overcome this limitation, the proposed method uses a fast algorithm to select the Regions of Interest (ROI) based on a global threshold, while the rest pixels are distinguished as clutter directly. The proposed method is verified by experiments with real multi-beam data. The results show that the proposed method can effectively solve the problem of false terrain in a multi-beam terrain survey and achieve a high detection accuracy.

• Journal of applied mathematics & informatics
• /
• v.30 no.3_4
• /
• pp.477-488
• /
• 2012

The convergence rate of a numerical procedure based on Schwarz Alternating Method(SAM) for solving elliptic boundary value problems depends on the selection of the interface conditions applied on the interior boundaries of the overlapping subdomains. It has been observed that the mixed interface condition, controlled by a parameter, can optimize SAM's convergence rate. In [8], one introduced the two-layer multi-parameterized SAM and determined the optimal values of the multi-parameters to produce the best convergence rate for one-dimensional elliptic boundary value problems. In this paper, we present a method which utilizes the one-dimensional result to get the optimal convergence rate for the two-dimensional problem.