• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.678-683
• /
• 2003

Ultrasonic method using SH(shear horizontal) wave has been developed to determine the surface damage in fatigued material. Fatigue damages based on propagation energy were analyzed by multiregression analysis and phase measurement in interrupted fatigue test specimen including CrMoV and 12Cr alloy steel. From the test results, as the fatigue damage increased the propagation time of the launched waves increased and amplitude of wavelet decreased. Also, analysis for the waveform modulation showed a reliable estimation, with confidence limit of 97% for 12Cr steel and 95% for CrMoV steel, respectively. Therefore, It is thought that SH ultrasonic wave technique can be applied to determine fatigue damage of in-service component nondestructively.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.6
• /
• pp.948-953
• /
• 2012

The characteristics of an induction motor vary with the number of parameters and the performance relationship between the parameters also is implicit. In case of the induction motor design, we generally should estimate many objective physical quantities in the optimization procedure. In this article, the multi objective design optimization based on genetic algorithm is applied for the three phase induction motor. The efficiency, starting torque, and material cost are selected for the objectives. The validity of the design results is also clarified by comparison between calculated results and measured ones.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.1
• /
• pp.12-15
• /
• 2014

At the moment of transformer energization by the supply voltage, a high current called transient inrush current, which may rise to ten times the transformer full load current, could be drawn by the primary winding. This paper discusses a microcontroller circuit with the intention of controlling and limiting the inrush current for a transformer, by the method of ramping up the supply voltage feeding to the transformer primary. Simulations and the experimental results show a significant reduction of inrush current, when the ramping up voltage is applied to the three-phase transformer load. The inrush current could be almost eliminated if the correct switching step rate is chosen.

• Nuclear Engineering and Technology
• /
• v.55 no.5
• /
• pp.1519-1526
• /
• 2023

For the first time Aluminium-BariumeZinc oxide nanocomposite (ZABONC) was synthesized by solution combustion method where calcination was carried out at low temperatures (600℃) to study the electromagnetic (EM) (X/γ) radiation shielding properties. Further for characterization purpose standard techniques like PXRD, SEM, UV-VISIBLE, FTIR were used to find phase purity, functional groups, surface morphology, and to do structural analysis and energy band gap determination. The PXRD pattern shows (hkl) planes corresponding to spinel cubic phase of ZnAl₂O4, cubic Ba(NO₃)₂, α and γ phase of Al₂O₃ which clearly confirms the formation of complex nano composite. From SEM histogram mean size of nano particles was calculated and is in the order of 17 nm. Wood and Tauc's relation direct energy band gap calculation gives energy gap of 2.9 eV. In addition, EM (X/γ) shielding properties were measured and compared with the theoretical ones using standard procedures (NaI (Tl) detector and multi channel analyzer MCA). For energy above 356 keV the measured shielding parameters agree well with the theory, while below this value slight deviation is observed, due to the influence of atomic/crystallite size of the ZABONC. Hence synthesized ZABONC can be used as a shielding material in EM (X/γ) radiation shielding.

• Korean Journal of Materials Research
• /
• v.26 no.10
• /
• pp.561-569
• /
• 2016

$SrAl_2O_4$: $Eu^{2+}$ and $Dy^{3+}$ phosphorescent phosphors were synthesized using the polymerized complex method. Generally, phosphorescent phosphors synthesized by conventional solid state reaction show a micro-sized particle diameter; thus, this process is restricted to applications such as phosphorescent ink and paint. However, it is possible to synthesize homogeneous multi-component powders with fine particle diameter by wet process such as the polymerized complex method. The characteristics of $SrAl_2O_4$: $Eu^{2+}$ and $Dy^{3+}$ powders prepared by polymerized complex method with one and two step calcination processes were comparatively analyzed. Temperatures of organic material removal and crystallization were observed through TG-DTA analysis. The crystalline phase and crystallite size of the $SrAl_2O_4$: $Eu^{2+}$ and $Dy^{3+}$ phosphorescent phosphors were analyzed by XRD. Microstructures and afterglow characteristics of the $SrAl_2O_4$: $Eu^{2+}$ and $Dy^{3+}$ phosphors were measured by SEM and spectrofluorometry, respectively.

• Journal of the Korean Ceramic Society
• /
• v.50 no.5
• /
• pp.333-340
• /
• 2013

To fabricate spherical lithium titanate ($Li_2TiO_3$) pebbles which are used for a breeder material in fusion reactor, titanium oxide ($TiO_2$) granules were used as a starting material. The granules were pre-sintered, and then aqueous lithium nitrate solution infiltrated into the granules at vacuum condition. The granules were crystallized to $Li_2TiO_3$ after sintering under the control of process parameters. In this study, the concentration of lithium in the solution, as well as the number of penetration times and sintering temperature affected the final crystallite phase and the microstructure of the pebbles. In particular, the sphericity and size of the pebbles were effectively controlled by a technical rolling process. The useful spherical $Li_2TiO_3$ pebbles which have 10~20% porosity and 60~120 N compressive strength were obtained through the sintering at $1000{\sim}1100^{\circ}C$ in the multi-times infiltration process with 50 wt% solution. The physical properties of pebbles such as density, porosity and strength, can be controlled by a selection of $TiO_2$ powders and control of processing parameters. It can be thought that the lithium penetration method is a useful method for the fabrication of mass product of spherical $Li_2TiO_3$ pebbles.

• Journal of Chest Surgery
• /
• v.37 no.2
• /
• pp.160-165
• /
• 2004

Successful treatment of multi-loculated pleural effusion or thoracic empyema requires effective drainage and definitive diagnosis of causative organism. The purpose of this study was to assess the efficacy of the video-assisted thoracoscopic surgery in the management of thoracic empyema or multi-loculated pleural effusion after chest tube drainage treatment had failed. Material and Method: Between April 2000 and July 2002, 20 patients with thoracic empyema or multi-loculated pleural effusion that failed to chest tube drainage or other procedures who underwent an operation. All patients were assessed by chest-computed tomogram and underwent video assisted thoracoscopic drainage, debridement, biopsy and irrigation of pleural cavity. Result: In 18 cases (90%), underwent successful video-assisted thoracoscopic surgery. In 2 cases, decortications by mini-thoracotomy were necessary. The ratio of sex was 4 : 1 (16 male: 4 female), mean age was 48.9 years old (range, 17∼72 years), mean duration of postoperative chest tube placement was 8.2 days (range, 4∼22 days), mean postoperative hospital stay was 15.2 days (range, 7∼33 days). Causative disease was tuberculosis, pneumonia, trauma and metastatic breast cancer, There were no major postoperative complications. Symptoms improved in all patients and were discharged with OPD follow up. Conclusion: In an early organizing phase of empyema or multi loculated pleural effusion, video-assisted thoracoscopic drainage and debridement are safe and suitable treatment.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.114-119
• /
• 2006

High critical current density, high n value, multiple faults endurances, and fast recovery characteristics of YBCO thin films are very attractive characteristics for developing resistive type superconducting fault current limiters. But due to the limited current and voltage ratings of one YBCO module, it is needed to construct series and parallel module connections for high capacity electric networks. Especially for distribution network, more than 30 units should be connected in series to meet voltage level. So in order to construct distribution-level superconducting fault current limiter, simultaneous quench in one YBCO thin films should be realized, and furthermore, quench should be occurred in all fault current limiting units equally to avoid local heating and failures. In this paper, we proposed optimum design of YBCO thin films for fault current limiting module and technical method using shunt resistor to achieve simultaneous quench between multi current limiting units. From the analytical and the experimental results, optimal current path and thickness of shunt material was determined for YBCO thin films and shunt resistor between modules was developed. Finally, 14 kV one phase resistive fault current limiter using multi YBCO thin films was constructed and it was possible to get satisfactory test results.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.6
• /
• pp.550-556
• /
• 2009

In an application of a time reversal(TR) focusing of array transducer on a defect inside the test material, we employ a new time delay focusing technique based the TR process. In order to realize this idea, a multi-channel ultrasonic system is constructed capable of applying necessary time delays to each channel. The TR-based focusing procedure first measures the backscattered signals after firing one of the array elements. A phase slope method is then used to determine the time-of-flights of the backscattered signals received by all elements of the array. These time delays are used to adjust the time of excitation of the elements for transmission focusing on the defect. In addition to the TR focusing, the classical phased array focusing is also considered for comparison. Experimental results show that the TR-based time delay focusing produces much stronger backscattered signals than the phased array focusing, demonstrating the enhanced capability of the TR focusing.

• Structural Engineering and Mechanics
• /
• v.67 no.4
• /
• pp.403-415
• /
• 2018

In the present study, nonlinear dynamic response of polymer-CNT-fiber multiscale nanocomposite plate resting on elastic foundations in thermal environments using the finite element method is performed. In this regard, the governing equations are derived based on Inverse Hyperbolic Shear Deformation Theory and von $K{\acute{a}}rm{\acute{a}}n$ geometrical nonlinearity. Three type of distribution of temperature through the thickness of the plate namely, uniform linear and nonlinear are considered. The considered element is C1-continuous with 15 DOF at each node. The effective material properties of the multiscale composite are calculated using Halpin-Tsai equations and fiber micromechanics in hierarchy. The carbon nanotubes are assumed to be uniformly distributed and randomly oriented through the epoxy resin matrix. Five types of impulsive loads are considered, namely the step, sudden, triangular, half-sine and exponential pulses. After examining the validity of the present work, the effects of the weight percentage of SWCNTs and MWCNTs, nanotube aspect ratio, volume fraction of fibers, plate aspect, temperature, elastic foundation parameters, distribution of temperature and shape of impulsive load on nonlinear dynamic response of CNT reinforced multi-phase laminated composite plate are studied in details.