• Polymer(Korea)
• /
• v.29 no.3
• /
• pp.300-303
• /
• 2005

Polyurethane multi-layer and foam multi-layer were prepared with PU1000 and PU2000 made by poly(propylene glycol) (PPG) having the molecular weight of 1000 and 2000 g/mol, respectively. The damping and transmission loss of these materials were compared with PU1000 used as a reference. The damping peak of polyurethane multi-layer was shifted to the lower temperature compared with PU1000, while the damping peak of polyurethane foam multi-layer was shifted to the higher temperature and broaden. In terms of noise reduction, the transmission loss of polyurethane multi-layer was effective at the specific frequency range such as less than 100 Hz and around 600 Hz compared with PU1000. The transmission loss of polyurethane foam multi-layer was most effective in the whole experimental frequency range.

• Journal of the Korea Society for Simulation
• /
• v.26 no.1
• /
• pp.69-75
• /
• 2017

An MCP(Multi-chip Package) is a package consisting of several chips. Since several chips are stacked on the same substrate, multiple assembly steps are required to make an MCP. The characteristics of the chips in the MCP are dependent on the layer sequence. In the MCP manufacturing process, it is very essential to carefully consider the layer sequence in scheduling to achieve the intended throughput as well as the WIP balance. In this paper, we propose a scheduling methodology considering the layer sequence constraint.

• Journal of the Korea Concrete Institute
• /
• v.17 no.1 s.85
• /
• pp.149-155
• /
• 2005

The purpose of this study is to investigate the flexural strengthening effects of CF(Carbon Fiber) sheet for the full-scale RC beams with multi-layer CF sheets. The partial strength reduction factors of CF sheets are suggested from the full-scale RC beams tests strengthened with multi-layer CF sheets up to six layers as well as material tests. From the material tensile tests, it was observed that the average tensile strengths of CF sheets per layer are decreased as the number of CF sheets is increased. Also the steep strength reductions of CF sheets in material test results at rupture are observed compared with the structural tests results for the full-scale RC beams strengthened with multi-layer CF sheets. Finally, the partial strength reduction factors far CF sheets up to six layers are suggested considering the effects of multi-layer and unit weight of CF sheets.

• Nuclear Engineering and Technology
• /
• v.51 no.4
• /
• pp.996-1007
• /
• 2019

We investigated the influence of the aspect ratio (H/R) of the oxide layer on the reactor vessel heating in three-layer configuration. Based on the analogy between heat and mass transfers, we performed mass transfer experiments to achieve high Rayleigh numbers ranging from $6.70{\times}10^{10}$ to $7.84{\times}10^{12}$. Two-dimensional (2-D) semi-circular apparatuses having the internal heat source were used whose surfaces of top, bottom and side simulate the interfaces of the oxide layer with the light metal layer, the heavy metal layer, and the reactor vessel, respectively. Multi-cell flow pattern was identified when the H/R was reduced to 0.47 or less, which promoted the downward heat transfer from the oxide layer and possibly mitigated the focusing effect at the upper metallic layer. The top boundary condition greatly affected the natural convection of the oxide layer due to the presence of secondary flows underneath the cold light metal layer.

• Proceedings of the KSRS Conference
• /
• v.2
• /
• pp.680-683
• /
• 2006

A one-dimensional planar model is considered of the atmosphere with multi-layer clouds illuminated by a mono-directional parallel flux of solar radiation. A new approach is proposed to radiation transfer modeling and daylight background formation for the atmosphere with such clouds that is represented as a heterogeneous multi-layer system each layer of which is described by different optical characteristics. The influence functions of each layer are determined by solutions of the radiation transfer boundary problem with an external monodirectional wide flux while the contribution of multiple scattering and absorption in the layer is taking into account.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.1
• /
• pp.65-69
• /
• 2003

ZnO-Si-ZnO multi-layer thin films have been deposited by pulsed laser deposition (PLD). And then, the films have been annealed at 300$^{\circ}C$ in oxygen ambient pressure. Peak positions of ultraviolet (UV) and visible region were changed by addition of Si layer. Mobility of the films was improved slightly than ZnO thin film without Si layer. The structural property changed by inserting intermediate Si layer in ZnO thin film. The optical properties and structural properties of ZnO-Si-ZnO multi-layer thin films were characterized by PL(Photoluminescence) and XRB(X-ray diffraction) method, respectively. Electrical properties were measured by van der Pauw Hall measurements

• Computers and Concrete
• /
• v.31 no.1
• /
• pp.9-21
• /
• 2023

The published studies usually used analytical method, numerical methods or experimental method to determine the stress-strain state and displacement of the single-layer or multi-layer curved shell types, but with a small scale model. However, a full scale multi-layer doubly curved concrete shell roof model should be researched. This paper presents the results of the experiment and simulation analysis involving stress-strain state, sliding between layers, the formation and development of the full scale double-layer doubly curved concrete shell roof when this shell begins to crack. The results of the this study have constructed the load-sliding strain relationship; strain diagram; stress diagram in the shell layers; the N_x, N_y membrane force diagram and deflection of shell. Thisresults by experimental method on a full scale model of concrete have clarified the working of multi-layer doubly curved concrete shell roof. The experimental and simulation results are compared with each other and compared with the Sap2000 software.

• KIEAE Journal
• /
• v.14 no.6
• /
• pp.93-97
• /
• 2014

Curtain wall system of office buildings has recently become very common in Korea. As the multi-layer curtain glazing is exposed to outdoor environment, it is very subjected to direct environmental impact. Consequently, breakage and cracks of glazing due to heat expansion is frequently observed. This study explores various causes and aspects for destruction of multi-layer glazing. A sensitivity analysis was performed on the basis that thermal changes causes damage to the multi-layer glazing. Air temperature in air cavity within the multi-layer glazing was examined to find its effect on multi-layer glazing breakage. Analysis showed high deflection to depth ratio of 1:1.8 and that higher the aspect ratio, smaller is the deflection. Allowable pressure showed that the weakest value is for aspect ratio of 1:2.9. Sensitivity analysis by the area of the glazing showed that as area of glazing becomes higher, allowable pressure and deflection-depth ratio becomes smaller. For allowable pressure and allowable deflection-depth within air cavity, the glazing breakage occurred at least $107^{\circ}C$. The results from glazing breakage by thermal factor shows that it is hard to break the glazing with only an increase in air cavity temperature in multi-layer glazing applied in buildings.

• Journal of Technologic Dentistry
• /
• v.41 no.3
• /
• pp.167-175
• /
• 2019

Purpose: This study was investigated the effect of multi-layer zirconia block type and design location on the mechanical properties of zirconia copings. Methods: Three kinds of multi-layered zirconia blocks (Snow princess multi layered block, Multi cherry, Dental zirconia pre-shaded blank) were used to identify the effects of the kinds of multi-layered zirconia blocks, design locations on mechanical characteristics of zirconia copings. 150 Zirconia copings were fabricated and fracture strength, hardness and microstructure were compared and evaluated. Results: Dental zirconia pre-shaded blank(2,256.9N) had the highest fracture strength of zirconia copings on all the design locations, and it was followed by Snow princess multi layered block(2,107.5N) and Multi cherry(917.0N). Snow princess multi layered block(1,949.7Hv) had the highest hardness of zirconia copings on all the design locations, and it was followed by Dental zirconia pre-shaded blank(1,671.7Hv) and Multi cherry(1,383.7Hv). The cervical layer had the highest fracture strength and hardness of zirconia copings in all the blocks, and it was followed by the cervical+gradation layer, the enamel layer, the enamel+gradation layer, and the gradation layer. Conclusion: It was found that the fracture strength and hardness were different according to the kinds of multilayer zirconia block and design location, and it was confirmed that it is lower than the fracture strength of white zirconia.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10a
• /
• pp.474-479
• /
• 1998

In this paper, the structural behavior of R.C. multi-layered floor structure including foam concrete layer is numerically analyzed. For the analysis, 3D interface element has been implemented to finite element analysis program to consider the interfacial behavior of multi-layered floor structure which consists of rubber layer, foam concrete layer and mortar layer on RC slab. Based on analysis results on multi-layered structure, its structural behavior is analyzed according to geometrical and material properties of foam concrete. Optimum material property of each layer of the floor structure is proposed to get optimum multi-layered concrete structure.