• 한국자동차공학회논문집
• /
• 제17권4호
• /
• pp.24-31
• /
• 2009

This paper has been focused on the development of integrated automotive muffler system to meet getting more stringent sound quality target. Typically, muffler system consists of resonator and main muffler. The many varieties in exhaust pipe routing and the flexibility in muffler design make it possible to design an exhaust system to deliver tailpipe sound for specific sound quality requirement. In recent, it is strongly recommended that the function of resonator be merged into that of main muffler due to severe space limitation of underbody. The main objective of the paper is to study the effects of various geometrical parameters on the muffler performance. This work has succeeded in eliminating resonator without loss of muffler performance. This work has also investigated the effect of diameter of hole, geometries of pipes and location of muffler on the sound quality.

• 한국소음진동공학회논문집
• /
• 제19권11호
• /
• pp.1202-1213
• /
• 2009

Muffler sound quality of a vehicle has widely been evaluated using commercial softwares. However, the commercial softwares are providing only simple sound quality index. To get better sound quality evaluation method of the muffler, a new approach is suggested based on the subjective sound quality test. The suggested subjective sound quality evaluation method is refined with the fuzzy theory. The developed method is applied for the evaluation of various kinds of vehicle muffler sounds.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.678-683
• /
• 2004

In this study, a experiment has been developed for measuring the exhaust pressure of muffler at inlet and outlet. The main experimental parameters were a engine speed and sound absorbing material in the muffler. The muffler sound absorbing material tested a steel wool and glass wool. The exhaust pressure was measured with pressure sensor. The phase of exhaust pressure with high speed was moved according to increasing engine speed comparing with exhaust pressure with low speed. Also, the distribution of exhaust pressure at the model-1, 2 and 3 are similar with distribution of exhaust pressure at muffler inlet.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1429-1436
• /
• 2000

Suction muffler is one of the important component of a compressor for low noise level and high efficiency. The suction muffler which has the complicated flow path gives the higher transmission loss of sound, but lower efficiency of compressor results from the superheating effect and flow loss in suction flow path. It is shown that the computational analysis of fluid dynamics are very popular methods for designing of high performance and low noise suction muffler. To reduce the thermodynamic and flow loss in suction process, the flow path of suction muffler was estimated by FVM(Finite Volume Method) and verified by experiments. And to enlarge the transmission loss of sound, the acoustic properties inside the suction muffler was analyzed by FEM(Finite Element Method) and experiments. The smart muffler which gives a good efficiency and low noise character was developed by using those methods, and the effect was evaluated in compressor by experiment.

• 한국소음진동공학회논문집
• /
• 제24권8호
• /
• pp.600-605
• /
• 2014

Two mufflers for a large-size sedan are suggested aiming (1) sporty-sound and (2) quiet-sound as well as both satisfying low back-pressure and low manufacturing cost. Transmission loss prediction considering heat and flow may increase the accuracy and reduce the development cost in muffler design; thus, GT-power prediction considering heat, flow, and acoustics is utilized. By understanding the fundamentals of flow-acoustic theory in small orifice(hole), an effective muffler design concept is proposed. Vehicle tests show the consistence with predictions for sound; also a back-pressure test bench confirms the advantage in pressure drop for both suggested mufflers. Those suggested mufflers also have advantages in manufacturing cost due to simplicity of the design.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.757-763
• /
• 2000

In vehicle exhaust systems the sound attenuation and the reduction of flow losses are often two competing demands. The present study considers a fully vehicle exhaust system and investigates experimentally both the sound attenuation and the flow performance of production configurations including the catalyst, the resonator, and the muffler. Dynamometer experiments have been This study is on the development of a new muffler composed of a valve system using an elasticity of spring. The valve system conducted with the daewoo 1500cc Lanos engine with speeds ranging from 1000 to 5000 rpm. Measurements include the flow rates, the temperatures and the absolute dynamic pressures of the hot exhaust gases at point locations. The present study describes the experimental aspects of an ongoing effort to validate and use the nonlinear fluid dynamic models in the time-domain for the prediction of the acoustic and power performance of firing internal combustion engines with full production exhaust systems.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권5호
• /
• pp.42-51
• /
• 2000

The performances of the simple expansion, perforated tube, and conical-connector type as an exhaust muffler are shown in this study. Applying a model in which the method of four-pole parameter is used makes theoretical estimation of the insertion loss. Experiment is performed for the measurement of the insertion loss under four cases according to the variation of the tail pipe length. By comparing the theoretical prediction with the experimental results, the validity of the modeling using the method of four-pole parameter is verified. The personal computer simulation programs for the above mentioned theory on the muffler design have been developed and exhaust sound level measurements have been carried out for simple expansion muffler, conical-connector muffler, perforated tube mufflers and the combined type of conical-connector and simple expansion muffler. The measured results for attenuation characteristics of noise for each muffler are compared with the computed theoretical results to verity the confidence and applicable limits of the theoretical equation derived.

• 대한기계학회논문집A
• /
• 제22권2호
• /
• pp.251-257
• /
• 1998

Active mufflers have been mainly applied in the large industrial engine due to considerable expense for implementation, but a necessity of development has been increased by the tightened regulation of exhaust noise and the request of high power. In this study, the active muffler prototype for installing in an automobile is designed and constructed. The active muffler is designed so that the primary noise and the control sound are propagated as a plane wave in the outlet. Therefore, the error microphone could be placed outside the high temperature centers of the tail pipe, and the noise radiating to the outside could be reduced in the whole areas around the outlet. For evaluating the control performance of the prototype, the control experiments of band-pass filtered random signal and the modulation of sinusoidal signal which are generated from the primary noise speaker as practical exhaust sound level are implemented. And to investigate the radiation pattern from the outlet of tail pipe and the noise reduction level of points placed adjacent to the outlet, the sound level of adjacent points of thirty is measured.

• 대한기계학회논문집A
• /
• 제21권11호
• /
• pp.1837-1843
• /
• 1997

This study experimentally demonstrates the use of active muffler attached to the automotive exhaust system to reduce exhaust noise. For improving the signal to noise ratio in the process of estimation of secondary path transfer functions, the on-line algorithm that conventional inverse modeling is combined with adaptive line enhancer is used as the control algorithm. Active muffler is designed that the primary noise and the control sound are propagated as a plane wave in the outlet. Therefore, the error microphone could be placed out of the tail pipe center of a high temperature and the radiation noise to the outside could be reduced in the whole area around the outlet. The control experiment for reducing exhaust noise with active muffler is implemented during run-up at no load. From the experimental results presented, compared with the conventional off-line method, the proposed on-line method is capable to acquire a reduction of exhaust noise above 5 dB in overall sound power level.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.365-370
• /
• 2000

This study represents effect to attain to the exhaust gas and the exhaust noise by the inner shapes of automobile muffler, and obtained optimization-data for the inner muffler shapes by the temperature variation of the exhaust gas in muffler. The results of noise show to decrease in order of model-1, 2 and 3 under that the engine speed is 3500 R.P.M and similar values beyond it. CO represented good the model-2 at low engine speed and model-1 at high engine speed. The model-3 was show to tiny variation difference by the variables. HC decrease mostly by increase of the engine speed and expressed low values the model-2 at 3,000 R.P.M and the model-1 at high speed. Wholly, the model-2 expressed stable results. The temperature distributions expressed high distributions by increase of the engine speed, and the model-3 was express most good among three models.