• Journal of Mechanical Science and Technology
• /
• v.20 no.12
• /
• pp.2087-2093
• /
• 2006

In this paper, auto focus actuator, which is used to move a lens module in the mobile phone having a camera module, is developed. Camera module containing auto focus actuator requires to minimize total size because of characteristics of the application area such as mobile phone, digital camera, and personal digital assistant. There are stepping motor, voice coil motor, and piezoelectric motor as auto focus actuator. In this paper, voice coil motor having new electromagnetic configuration is proposed. And actuator using proposed voice coil motor is developed by optimal design method using magnetic circuit analysis. The sectional area of the developed actuator is reduced to 32.4% compared with actuator using general electromagnetic configuration. From the performance test, the developed actuator has moving stroke of 0.64 mm for 2.1 volt, hysteresis of 40 $\mu$m, full stroke current of 54 mA, and unit step motion of 3 $\mu$m.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.9
• /
• pp.459-464
• /
• 2006

The detent force by end-effect has an undesired influence on moving coil type Permanent Magnet Linear Synchronous Motor(PMLSM). So, the reduction of detent force by end-effect is especially required for the improvement of thrust characteristics. In this paper, in order to reduce detent force by end-effect, the auxiliary-teeth is installed at the end part of mover. It is also analyzed by Finite Element Analysis(FEA) and optimized by using neural network. By comparison, the detent force is reduced about 41.4[%] comparing to that of basic model.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.378.2-378
• /
• 2002

This paper deals with a moving coil type linear motor for fast access of the miniature ODD. This slim-line motor is composed of the mover supported by guide mechanism, the coil wound into it, and the yoke attached to the permanent magnet for stator. The driving force is generated by the PM of the stator and the current in the coil of the mover. Magnetic circuit analysis and Finite Element Method are applied to estimate force at air gap. (omitted)

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.1
• /
• pp.17-22
• /
• 2016

A voice coil actuator with moving coil type for scanning mirror system of barcode reader has been developed. The actuator has a simple structure including a magnet, a coil and a pin. The performance of the actuator is analyzed by a linearized theoretical model. And the dynamic performance of the proposed actuator is predicted through motor constant and restoring constant obtained by finite element simulations. The theoretical model was verified by the prototype which has 64 Hz resonance frequency and 60 deg reflecting angle. We also discovered that that 3 V input can make the actuator rotate over 61.8 deg reflecting angle at 50 Hz resonance frequency. The proposed actuator can simplify its driving configuration because of its implementation of open-loop control.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.224-227
• /
• 1998

Linear motors are increasingly employed as direct actuators replacing the more conventional systems composed by a rotating motor and a mechanical device. Linear DC motor is useful in a high speed and high accuracy positioning system with a feedback controller. Because of these advantages, linear DC motors have already been used as motors of pen recorders and magnetic disk storage devices, these are moving coil type linear DC motors as these movers are light. Moving magnet type linear DC motor has advantages at long stroke motors because its mover's feeding wires for driving is not necessary. This paper is concerned with the analysis of linear DC motor that is moving magnet type with unipolar. In order to analyze the dynamic behaviour a mathematical model based on a simplified field analysis developed. A two dimensional finite element field solution is employed in order to illustrate the effect of yoke saturation and motor performance. It is deduced the relation between the limit value of the thrust of the linear DC motor and the dimension of the yokes.

• Journal of Industrial Technology
• /
• v.21 no.B
• /
• pp.117-123
• /
• 2001

In a modern control field, a control engineer who has theoretical backgrounds with some practical knowledge is demanded. That is to say, an engineer who can understand and operate the various parts such as modeling, simulation, system analysis, signal processing, statistics, and hardware is required. In order to prove the theoretical backgrounds and operate various hardwares, a lot of experimental devices for students are designed in universities. Since the conventional experimental devices are manufactured abroad and the prices of the devices are too high, it is difficult to have. If a low cost experimental device can be developed, it will be very useful for a control engineering education. In Ibis paper, an experimental rig which has two control inputs and three sensor outputs to control the end point of a flexible beam is designed and manufactured. This rig can be used for a control field education.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.82-84
• /
• 1998

LDM(Linear DC Motor) are used in high speed, high-precision position control system. Because of these advatages, LDM has already used in the motor of pen-recorder, magnetic-disk devices. Under the limited dimension, we propose the design method of LDM by magnetic circuit. In this paper, a relation between the thrust constant and size of a LDM that is moving coil type with unipolar is described, which is defined as a simple relational equation. To maximize the rate of thrust to the volume of LDM, the magnetic flux density in the yoke is adjusted to the value of magnetic equation By the magnetic field analysis(FEM), the validity of the equation is confirmed.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.120-123
• /
• 1994

The purpose of this paper is to describe the mutual inductance between two non-coaxial circular coils in coil gun. As being in many electromagnetic applications, one of them is fixed and the other one is moving and, being not supported, its axis may not coincide with the axis of the fixed coil. This paper presents a method for the calculation of the mutual inductance in case of non-coaxial coupled coils, the characteristics of this inductance and experimental results. For the computation, the complete elliptic integrals formula and mesh matrix technique were introduced. This method enables accurate results from relatively simple procedure and calculation program.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2008.12a
• /
• pp.95-95
• /
• 2008

• Journal of Mechanical Science and Technology
• /
• v.20 no.9
• /
• pp.1371-1381
• /
• 2006

This paper deals with the active vibration control of a simply-supported beam traversed by a moving mass using fuzzy control. Governing equations for dynamic responses of a beam under a moving mass are derived by Galerkin's mode summation method, and the effect of forces (gravity force, Coliolis force, inertia force caused by the slope of the beam, transverse inertia force of the beam) due to the moving mass on the dynamic response of a beam is discussed. For the active control of dynamic deflection and vibration of a beam under the moving mass, the controller based on fuzzy logic is used and the experiments are conducted by VCM (voice coil motor) actuator to suppress the vibration of a beam. Through the numerical and experimental studies, the following conclusions were obtained. With increasing mass ratio y at a fixed velocity of the moving mass under the critical velocity, the position of moving mass at the maximum dynamic deflection moves to the right end of the beam. With increasing velocity of the moving mass at a fixed mass ratio ${\gamma}$, the position of moving mass at the maximum dynamic deflection moves to the right end of the beam too. The numerical predictions of dynamic deflection of the beam have a good agreement with the experimental results. With the fuzzy control, more than 50% reductions of dynamic deflection and residual vibration of the tested beam under the moving mass are obtained.