• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.8
• /
• pp.106-113
• /
• 1995

Surface mounters are used to mount the parts of electronic products on PCB(Printed Circuit Board. Those machines rely on high precision, high productivity, and software for accomodation of use. In this paper, two algorithms and a software which can give the users the acco-modation and high productivity for rotary type surface mounters are presented. The algo- rithms for development of of the software consider all factors which affect the effeciency of the operation. And the interface between user and machine for the accomodation of use can be achieved through the developed software.

• Development and Reproduction
• /
• v.1 no.2
• /
• pp.181-187
• /
• 1997

This study has been conducted to investigate the mating behavior, time sequence of mating and time limit with which female can fulfill spawning and brooding after pre-spawning molting in the giant fresh-water prawn, macrobrachium rosenbergii reared in the laboratory. the results obtained were summarized as follows. Mating happened spontaneously as the following sequences: courting gesture, seizure of female by male, mounting, turning of female, copulation. The entire mating lated approximately seven minutes. The endopodite of 2nd pleopod of male bore the appendix masculins whcih are male's secondary sex characteristic. cinciulli was formed at the distal portion of appendix interna which are on the upper portion of appendix masculins and helped stabilizing the connection of each side of 2nd pleopod during mating. After the connection of each side of 2nd plepod was fixed on the posterior portion of the thoracic sternum in female, a gelatinous spermatophore that emitted at the basipodite of 5th pereiopod during courting gesture was deposited on the ventral groove of 2nd, 3rd, 4th and 5th pereiopod. time limit which female can fulfill copulation and brooding was from 3 hours to 15 hours after pre-spawning molting.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1994.06a
• /
• pp.912-918
• /
• 1994

Poor speech intelligibility in an air traffic control room is frequently a result of many, quite different causes and occasionally leads to complaints of the controller personnel. The paper describes a sequence of successful tasks performed in a local control room. The initial measurements included an investigation of the background noise (caused by fans, air condition, computer and radar equipment) and performance checks of the electronic audio and communication equipment with respect to the audio transmission behavior. The spectral composition of the noise as well as the characteristics of the audio communication path between the controllers and the pilots(which showed a loss of spectral information in the audio band due to built-in notch filters for the suppression of control tones) required adaptations of the amplitude behavior of the amplifiers through user adjustable tone controls. The radar console fans, which contributed significantly to the overall noise floor of the room, underwent a substantial reconstruction by replacing the tight mounting with an elastic double suspension, reducing the noise level by 50%. Finally, a possible source of untimely fatigue of the controllers during their working hours has been found in strong spectral components of the noise above the audio band, radiated by numerous video monitors in the control through vibrating components excited by the line frequency of the video signal.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.4
• /
• pp.1812-1816
• /
• 2011

This research developed chemical flow control system(CFCS) essential for spinner equipment in nano semiconductor manufacturing process under the 100nm to prevent complex process defect due to missing spread after chemical injection. The devices developed in this research, which can be swiftly replaced in case abnormal state element changes or wafer manufacturing defect occurs, are anticipated to improve module yield as well as real-time monitoring on the state element. In addition, as a result of mounting H/W and S/W system to control detailed operation sequence in production line and executing performance check and verification, we can be exactly detected in five abnomal process type.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.7
• /
• pp.1725-1728
• /
• 2009

This research developed process control device and FGV pattern generating device essential for full gate visual inspection to improve process so that defect detection capability may be maximized in specified environment. The devices developed in this research, which can be swiftly replaced in case loss or error occurs, are anticipated to improve module yield as well as maintain tact loss near '0'. In addition, as a result of mounting H/W and S/W system to control detailed operation sequence in production line and executing performance check and verification, detection rates were 98.1% and 99.1% respectively for pixel defect by tact and line defect, and yield of the entire module process including gate and visual level test increased up to 98.3%.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.23 no.5
• /
• pp.502-515
• /
• 2020

To identify the dynamic characteristics of the Auto-leveling system applied to the Tractor-Trailer type Transporter for mounting a large scale precision equipment, Dynamics Modeling & Simulation were performed using general Dynamics Analysis Program - RecurDyn(V9R2). The axial load data, transverse load data and pad trace data of leveling actuators were obtained from M&S. And they were analyzed and compared with each other by parameters, i.e. friction coefficients on the ground, landing ram speed of actuators, and direction & quantity of ground slope. It was observed that ground contact friction coefficients affected to transverse load and pad trace; the landing ram speed of actuators to both amplitude of axial & transverse load, and this phenomena was able to explain from the frequency analysis of the axial load data; the direction of ground slope to driving sequence of landing ram of actuators. But the dynamic behaviors on the two-directional slope were very different from them on the one-directional slope and more complex.

• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.3
• /
• pp.97-103
• /
• 2018

This paper addresses an improved naval combat UPS(Uninterruptable Power Supply) system under abnormal transients. Previously, thermistor and varistor elements were used to cope with transient overvoltage and overcurrent, however the UPS was frequently unavailable because it was vulnerable to abnormal transient voltage generated during system operation. In order to overcome this problem and protect UPS system, this paper proposes an input power cut-off circuit that detects the initial input power and abnormal transient voltage generated during operation, improvement of power control sequence, and a method to prevent malfunction of an inverter and CPU. The UPS system implementing the proposed method was simulated by input power variable test using programmable AC/DC generator, and finally validated its reliability and stability through field tests by mounting on multifunctional console of naval combat system.

• KIPS Transactions on Computer and Communication Systems
• /
• v.5 no.12
• /
• pp.491-498
• /
• 2016

Recently leakages of confidential information and internal date have been steadily increasing by using booting technique on portable OS such as Windows PE stored in portable storage devices (USB or CD/DVD etc). This method allows to bypass security software such as USB security or media control solution installed in the target PC, to extract data or insert malicious code by mounting the PC's storage devices after booting up the portable OS. Also this booting method doesn't record a log file such as traces of removable storage devices. Thus it is difficult to identify whether the data are leaked and use trace-back technique. In this paper is to propose method to help facilitate the process of digital forensic investigation or audit of a company by collecting and analyzing BIOS firmware images that record data relating to BIOS settings in flash memory and finding traces of portable storage devices that can be regarded as abnormal events.