• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 D
• /
• pp.2067-2069
• /
• 2003

본 연구는 진동 신호의 전력 스펙트럼 밀도(PSD)해석을 이용하여 베어링 초기 고장을 검출할 수 있는 기법을 제시하였다. 외륜, 내륜, 볼에 대하여 각각 폭 0.3 mm의 미소한 흠을 낸 베어링을 이용하여 고장 특성 주파수 패턴 및 부하변동에 따른 영향을 분석하고 고장검출이 용이한 고장 주파수 대역을 설정하였다. 실험결과로부터 제시된 검출기법이 유도전동기 베어링 초기 고장에 적용 가능함을 입증하였다.

• 전기학회논문지
• /
• 제57권4호
• /
• pp.617-624
• /
• 2008

This paper proposes design and implementation of wind turbine simulators which incorporate the turbine dynamic characteristics. At first, the turbine output characteristic in steady state is modelled as a function of wind speed and then dynamic characteristics are modelled such as pitch angle control, torsional vibration, tower shadow effect, wind shear effect, and inertia effect. In addition, a wind speed simulator is developed which can generate the real wind speed pattern. The wind turbine simulator is implemented with 3[kW] M-G set(cage-type induction motor coupled with doubly-fed induction generator) at laboratory.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.85-87
• /
• 2001

Linear motor damper(LMD) for vibration control of structure is consisted of the NdFeB permanent magnets with high specific energy as the stator, a coil-wrapped nonmagnetic hollow rectangular structure and an iron core as a pathway for magnetic flux. The active mass of LMD is 1.5 ton and consisted of permanent magnet and iron yoke. In this paper, LMD system is manufactured and tested for dynamic characteristics and frequency response.

• 동력기계공학회지
• /
• 제10권4호
• /
• pp.181-186
• /
• 2006

In this paper, a noncontact type torque meter using silicone rubber to measure the exact torque value and reduce a vibration and a noise, was developed. When planetary gear speed reducer runs, torque, RPM etc.. of motor change according to load or speed change. So, it needs a device to detect load's change or to diagnose the state of thewhole drive department by monitoring these result values. The noncontact type torque meter using silicone rubber that we're trying to develop this time is low-cost and can measure RPM and torque value simply. Also, it caculate a power using this value and indicate them on screen.

• 동력기계공학회지
• /
• 제17권4호
• /
• pp.139-146
• /
• 2013

Because the magnetic bearing supports levitating body without contact, wear, noise and vibration, it is very useful to high revolution machinery. In this paper we selected ATmega 128, a less expensive and widely used micro controller, for control the magnetic bearing system. And we selected the sampling time and the control gain of PID controller through trial-and-error. The control program of the one board controller utilized lookup table to reduce calculation time, and bit shifting for the integer calculation in instead of floating point calculation. As the results, the controller carried out relatively high speed PID control on sampling time 0.25 ms. At last the rotation test for the magnetic bearing system was carried out by 3 phase induction motor and air turbine.

• 소음진동
• /
• 제10권1호
• /
• pp.97-106
• /
• 2000

The dynamic behavior of crankshaft-bearing system in scroll compressor has been investigated using the combined methodologies of finite elements and transfer matrices. The finite element formulation is proposed including the field element for a shaft section and the point element at balancer weight locations, bearing locations, etc., whereas the conventional method is used with the elements. The Houbolt method is used to consider the time march for the integration of the system equations. The linear stiffness and damping coefficients are calculated for a finite cylindrical fluid-film bearing by solving the Reynolds equation, using finite difference method. The orbital response of crankshaft supported on the linear bearing model is obtained, considering balancer weights of motor rotor. And, the steady state displacement of crankshaft are compared with a variation in balancer weight. The loci of crankshaft at bearing locations are composed of the synchronous whirl component and the non-synchronous whirl component.

• 한국소음진동공학회논문집
• /
• 제12권10호
• /
• pp.758-765
• /
• 2002

KITECH and ODS performed a study of internal and external noise prediction of the Korean high speed prototype test train(HSR 350X). The object of this study was 3 kinds of cars, trailer car(TT2), motorized car(TMI ) and power car(TPI) and the predicted noise was for the two different driving speeds in free field and tunnel conditions. Data of carbody design and noise sources were delivered from manufactures. Some of noise sources which were not available in the project team, were chosen by experiences of ODS. Internal noise level of each car was predicted for two cases i.e, at 300 km/h and 350 km/h. In addition sound transmission path and dominant noise sources were also investigated for each section of the car, which is circular shell typed part of whole carbody. In case of TT2, the dominating sound transmission path is the (floor in terms of structure-borne noise and air-borne noise. The main noise sources are structure-borne noise from the yaw-damper and air-borne noise from the wheel/rail contact, whereas the dominating sound transmission path of TMI are floor and sidewall below the window in terms of structure-borne noise. The main noise sources of TMI are structure-borne noise from motor/gear unit and the yaw-damper in the free field, and air-borne noise from the wheel/rail contact and structure-borne noise from motor/gear unit in the tunnel. Through the external noise prediction for the KHST test train formation, the noise form the wheel/rail contact is estimated as one of the major sources. In addition, the noise specification of sub-component was proposed for managing each sub-surpplier to reach the KHST noise requirement. The specification provide the sound power of machinery part and transmission loss of component of carbody structure. The predicted noise level in each case exceeded the required limit. Through this study, the noise characteristics of the test train were investigated by simulation, and then the actual test will be performed in near future. Both measured and calculated data will be compared and further work for noise reduction will be continued.

• 한국철도학회논문집
• /
• 제16권1호
• /
• pp.7-13
• /
• 2013

철도차량의 실차 규모 동특성시험은 설비 구축, 대차의 제작 및 시험 조건의 설정등과 관련하여 비용, 시간 등의 증대로 많은 어려움이 따른다. 본 연구에서는 실험실 환경에서 차량 진동문제와 안전성을 평가하기 위한 목적으로 축소모델을 제작하고, 개발된 축소모델이 해당 철도차량의 동특성을 정밀하게 모사하는지를 검증하는 평가방법에 대한 연구를 수행하였다. 축소이론은 Jaschinski 상사기법의 이론을 적용하였으며, 1/10 축소모델을 구축하였다. 본 연구에서는 축소 대차의 상하 진동에 초점을 맞혀 시스템을 제작하였다. 시스템은 구동부, 보기, 대차 등 3개의 하부구조로 구성되었으며, 실제 차량으로 환산 시 400km/hr까지 실험가능 하도록 목표로 하였다. 축소 대차의 설계 및 제작과 함께, 동역학해석 프로그램인 ADAMS/View를 이용하여 고유치 해석을 수행하였다. 전산해석으로 도출된 고유진동수는 실험결과와 비교 분석되었다. 시스템이 가지고 있는 초기 5개의 자유도에 상응한 고유진동수를 비교한 결과, 개발된 상사 이론에 따른 축소모형은 충분한 신뢰성을 확보한 것으로 검증되었다. 본 연구에서 개발된 축소모델은 대학실험실에서 차량진동모드를 모사하는 용도로 기획되었으나, 추후 자유도의 추가보완을 통해 고속철도 차량의 대차와 보기구조 동특성 해석에 활용될 수 있을 것으로 판단된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.917-923
• /
• 2002

KITECH and ODS performed a study of internal and external noise prediction of the KHST test train. The object of this study was 3 kind of cars; trailer car(TT2), motorized car(TM1) and power car(TP1) and the predicted noise was calculated for the two different driving speeds in free field and tunnel conditions. Data of carbody design and noise sources were delivered from each manufactures. Some of noise sources which were not available in project team, were chosen by experiences of ODS. Internal noise level of each car were predicted for two cases i.e, at 300 km/h and 350 km/h. In addition sound transmission path and dominant noise sources were also investigated of each section of car, which is circular shell typed part of whole carbody. In case of TT2, the dominating sound transmission path is floor in terms or structure-borne noise and air-borne noise. The main noise sources are structure-borne noise from the yaw-damper and air-borne noise from the wheel/rail contact, whereas the dominating sound transmission path of TM1 are floor and sidewall below the window in terms of structure-borne noise. The main noise sources of TM1 are structure-borne noise from motor/gear unit and the yaw-damper in the free field, and air-borne noise from the wheel/rail contact and structure-borne noise from motor/gear unit in the tunnel. Through the external noise prediction for the KHST test train formation, the noise form the wheel/rail contact is estimated as one of the major sources. In addition, the noise specification of sub-component was proposed for managing each sub-surpplier to reach the KHST noise requirement. The specification provide the sound power of machinery part and transmission loss of component of carbody structure. The predicted noise level in each case exceeded the required limit. Through this study, the noise characteristics of the test train were investigated by simulation, and then the actual test will be performed in near future. Both measured and calculated data will be compared and further work for noise reduction will be continued.

• 대한통합의학회지
• /
• 제3권3호
• /
• pp.59-71
• /
• 2015

Purpose : This study examines the effect of vibration exercise grafting PNF patterns for 6 weeks on upper body stability and equilibrium for seniors having fifteen or over of MMSE-K. Method : A total of 10 senior citizens participated in this study. Each participant performed PNF patterned exercises using vibration sports equipment for 30 minutes, once static a week, for six weeks. We measured trunk stability and balance degree before and after the six-week exercise program. Motor Assessment Scale (MAS) was used to measure trunk stability, while Functional Reach Test (FRT) and Timed Up and Go (TUG) was used to measure balance degree. The collected data was processed using paired t-test to confirm the difference between pre-program conditions and post-program conditions. Results: The results of our study show that post-program trunk stability measurements increased when compared to pre-program data; however, this increase was not statistically significant. pre and post-measurements for satatic balance and dynamic balance were statistically unchanged. Conclusion: Due to limitations in the number of participants, the procedural design of this experiment, and the limited amount of time participants actually controlled, this study failed to produce statistically significant results. However, further study should be conducted using a systematically implemented exercise program to show support for exercising with flexi-bar as an effective program for the elderly.