• 한국정밀공학회지
• /
• 제26권1호
• /
• pp.71-81
• /
• 2009

Die steel for plastic molding were used as mold material of automobile parts and electronic component industry. The material of this paper has superior to mechanical properties, such as repair weldability, corrosion resistance and high temperature strength, required mold parts for semitransparent. Laser-induced surface hardening technology is widely adopted to improver fatigue life and wear resistance via localized hardening at the surface of mold parts. The objective of this research work is to investigate on the characteristics of surface hardening of the laser process parameters, such as beam travel speed, laser power and defocsued spot position, for the case of die steel for plastic molding. Lens for surface hardening of large area is plano-convex type with elliptical profile to maintain uniform laser irradiation. According to the experimental results, large size of hardened layer at the surface of die steel for plastic molding was achieved, and microstructure of this layer was lath martensite. Optimal surface status and mechanical property of hardened layer could be obtained at 1095Watt, $0.25{\sim}0.3m/min$, 0mm (focal length: 232mm) for laser power, beam travel speed, and focal position. Where, heat input was $0.793{\times}10^{3}J/cm^2$, and width of hardened layer was 27.58mm.

• Design & Manufacturing
• /
• 제11권3호
• /
• pp.1-7
• /
• 2017

The fabrication process of micro pattern structure with high precision and high aspect ratio using powder injection molding (PIM) is developed. In the PIM process, the metal powder is mixed with the binder systems and the mixture is injected into the metal mold. The injection molded green parts are debinded and sintered to reach final shape and properties. In this method, the optimization of physical properties such as fluidity and strength of the binder system is essential for perfect filling the high aspect ratio micro-pattern. For this purpose, the correlation between the properties of the binder system and feedstock and ${\mu}-PIM$ process was investigated, and a binder system with low viscosity at low temperature(about $110^{\circ}C$) and high strength after cooling was investigated and applied. Employing this process, high precision parts with line type micro pattern structure which has pattern size $160{\mu}m$ and aspect ratio more than 2 can be manufactured.

• Design & Manufacturing
• /
• 제6권1호
• /
• pp.90-94
• /
• 2012

Recently, injection molding process became more popular than ever to produce large quantities of high precision products. Extensive studies have been conducted for reducing the residual stresses and birefringence in injection-molded optical products. Flow-induced and thermally-induced stresses and birefringence have been found as two main sources during injection molding process. Generally, quantitative value of birefringence can be measured with polarizing microscope using the compensator. However, it is difficult to measure low order retardation with microscope, so developing a measurement system for low order optical path difference is in need. In the present paper, a system using Photo Elastic Modulator (PEM) is demonstrated to measure low phase retardation in injection-molded products.

• Design & Manufacturing
• /
• 제8권2호
• /
• pp.50-55
• /
• 2014

Recently, semi-stack mold have been developed for satisfying the various elements required in the mold industry. The mold is possible using with general-purpose injection molding machine by weight reduction through the improvement of the mold structure. In order to do that, tension core, spiral cooling system and half runner system were applied. It is effective for increased productivity and decreased of loss to the materials. However, the mold is required the filling balance in order to improve the quality and efficiency. Thus this study performed that optimum design and analysis of semi-stack mold for filling balance.

• Design & Manufacturing
• /
• 제1권1호
• /
• pp.39-44
• /
• 2007

In recent, recycling of plastic material has became a major issue due to the landfills and environmental problem. This study investigated fluidity and hardness of thermoplastic vulcanizate(TPV), which is used for automobile component parts such as weather strip in order to replace ethylene propylene rubber (EPDM). So, using the spiral flow test mold, we conducted an experiment on fluidity and hardness of TPV according to injection molding conditions. As results of injection molding experiment, the recycled TPV's flow length was a little bit longer than virgin TPV and the hardness was decreased in case of using the recycled resin. Also, we investigated the morphology study by SEM photo.

• Design & Manufacturing
• /
• 제10권3호
• /
• pp.8-13
• /
• 2016

Despite technological advance, there have been several troubles in photo reaction injection molding (photo RIM) to produce ultra thin light guide panels (LGPs). In this study, micro leakage problem at cavity edge during photo RIM was investigated numerically. In order to obtain optimal processing conditions, we regulated inlet pressure of injected resin at the cavity edge and figured out micro leakage behaviors. At low inlet pressure (less than 100 Pa), though the micro leakage problem was not occurred, another problem, short shot due to not enough driving force, was appeared More than 1,000 Pa of the inlet pressure, injected resin was rapidly leaked through the micro gap at the cavity edge. Finally, we obtained optimal inlet pressure around 600 ~ 1,000 Pa. At this region, injected resin fully filled the cavity without micro leakage behavior. Based on the present study, further comparative investigations with experimental photo RIM should be performed to find optimal processing conditions for produce ultra thin LGPs.

• Design & Manufacturing
• /
• 제2권1호
• /
• pp.51-56
• /
• 2008

Recently, the demand of high-productivity injection mold increases since the consumption of packaging grows in the world. Stack mold is composed of more than two molds and it has very high productivity and economic efficiency. In this study, stack mold was developed to improve productivity of vehicle fixed weather strip with TPV materials and to investigate the characteristic of injection molding using CAE.

• Design & Manufacturing
• /
• 제2권4호
• /
• pp.5-10
• /
• 2008

Recently, the study for filling imbalance in thermoplastic polymer has gradually been increased. However, it is hard to find the researches for filling imbalance of thermoplastic elastomer(TPE). The experiment of filling imbalance was conducted for the three kinds of thermoplastic vulcanizes(TPVs) and PP polymer in the mold with geometrically balanced runner system(Unary Branch Type Runner System). In this experiment, the effects of the melt temperature, injection pressure and injection speed on the filling imbalance were investigated. There was also the imbalance in TPV injection molding process as well as in conventional injection molding with plastics. The tendency of filling imbalance in TPV injection molding specially decreased by taking place the hesitation of TPV melt.

• Design & Manufacturing
• /
• 제13권1호
• /
• pp.36-41
• /
• 2019

A large plastic molding requires an injection molding with a large clamping force. However, it could not be prepared in the manufacturing at any time. In order to solve the problem, the injection molding analysis study was conducted on the back cover of 55 inch LED TV. The study compared the case of applying the existing flow system such as hot runner, the improvement of the hot runner lay-out and the precise control of the gate operation time, From the results of using the improved flow system, it was found that the welding and the clamping force were considerably improved as compared with before the improvement. In particular, the clamping force was reduced by 50% compared with before the improvement.

• Design & Manufacturing
• /
• 제10권3호
• /
• pp.20-24
• /
• 2016

Foaming is a step of forming by the ratio of the internal combustion chamber in a state where the in flow of the material is suppressed, if the diameter is small and a high to a crack generated on the molding is not possible. The present study, we studied using as part experiments for forming the circular shape of the forming height of 10 mm without the occurrence of cracks, results preformed primary, the need to set the height of the forming than the height of the product, preformed secondary. It was able to increase the height of the molded product with less than the height of the next step to be carried out compression processing to create a small comer of the desired shape. In addition, it was found that on a great influence on the quality of the final quality on the final molding of the primary preformed, secondary.