• Design & Manufacturing
• /
• 제10권2호
• /
• pp.44-49
• /
• 2016

The roll forming produces mass products using the continuous production process. Also we need the process that continuous long material or goods cutting into a desired length. Our study uses 3-D driving cutter and roll forming material as SPCC to investigate this. When we cut the material using the process of roll forming, the shear resistance is raised at the cutting punch's edge. The result is remained the trouble about burr and progressive deformation on the material. This study shows the method minimizing the above trouble. The material of punch was considering heat generated on the continuous production process. So we used the type of STD 61 for the material of punch and had the vacuum heat treatment for the surface hardness of HRC 53. The structure of the mold is designed with forming a double cam die at the upper punch and the both sides of central core. We conducted the experiment three times. In the result when had to make V-groove within the angle between 105 and 110 on the punch front end, we could get the minimum shear resistance on the punch front end. Also with the same condition we minimizes the material jams in the continuous production process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.347-350
• /
• 2001

A typical Mold method is to form a gate electrode, a gate oxide, and emitter tip after fabrication of mold shape using wet-etching of Si substrate. In this study, however, new Mold method using a side wall space structure is used in order to make sharper emitter tip with a gate electrode. Using LPCVD(low pressure chemical vapor deposition), a gate oxide and electrode layer are formed on a Si substrate, and then BPSG(Boro phospher silicate glass) thin film is deposited. After, the BPSG thin film is flowed into a mold as high temperature in order to form a sharp mold structure. Next TiN thin film is deposited as a emitter tip substance. The unfinished device with a glass substrate is bonded by anodic bonding techniques to transfer the emitters to a glass substrate, and Si substrate is etched using KOH-deionized water solution. Finally, we made sharp field emitter array with gate electrode on the glass substrate.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.99-100
• /
• 2007

Transferring patterns from mold to PDMS stamp is very useful technology in micro-fabrication, complex and three-dimensional structures. First experimentation, mold's patterns wens transferred to PDMS stamp. Comparing with PDMS stamp and Mold, patterns were transferred about 97.9%. Second experimentation, PDMS stamps were made several times by only one mold, scale and distance of transferred patterns were uniform about 89.3%. We proved that transferring patterns from mold to PDMS stamp is accurate. The uniformity of stamps is the same after mold was used several times. Transferring patterns from mold to PDMS stamp has uniformity and accuracy, it will be useful technology.

• 펄프종이기술
• /
• 제48권3호
• /
• pp.66-72
• /
• 2016

The applicability of rice husk fiber as a raw material for eco-friendly pulp mold was evaluated in this study. The higher demand of environmental friendly packaging material resulted in the more interest for the natural fiber based pulp mold. The rice husk which is an abundant agricultural byproduct in Asia could be defiberized by an alkaline digestion process. The changes in the pulp mold making process and the properties of pulp mold by the addition of the rice husk were investigated. The addition of rice husk fiber to the pulp mold made with OCC or UBKP resulted in the increase in drainage at the pulp mold forming process. In case of UBKP pulp mold, the addition of rice husk fiber increased the drying efficiency after pulp mold forming since the structure of pulp mold became more bulkier by the addition of the rice husk fiber. Those results showed the rice husk fiber could be applied to the pulp mold manufacturing as one of the eco-friendly natural fiber resources.

• 한국표면공학회지
• /
• 제41권5호
• /
• pp.245-253
• /
• 2008

The porous metal material is used for injection metal mold with a great deal of gas production because it makes plenty of gas exhausted through pores formed in the metal mold. A canning HIP method was conventionally used for manufacturing of porous metals, but because of difficulty of process control and high cost of production its application was limited. In this experiment, porous metal mold material was produced by an enhanced vacuum sintering method with simply controlled and economical process and porosities/mechanical properties with variation of sintering temperature and duration time during vacuum sintering were studied. As a result, quality goods were obtained at optimized conditions as follows: sintering temperature of $1230^{\circ}C$, duration time of 2 hr and showed superior properties in wear loss and thermal conductivity and the same properties in hardness, TRS (Transverse Rupture Strength), and thermal expansion coefficient in comparison with those under canning HIP.

• Design & Manufacturing
• /
• 제14권1호
• /
• pp.22-29
• /
• 2020

The analysis was carried out using the press molding analysis program by applying six parameters such as material type change, material thickness, friction coefficient, r_p, r_d and blank holder pressure. As a result of CAE analysis of the soft material DC04 and the relatively hard material HX300LAD, the thickness of the punch R part of the soft material was significantly reduced. The flange portion is greatly increased in thickness in the hard material by the compression action. As a result of considering the deformation amount of 0.6mm, 1.0mm, 1.5mm according to the material thickness, the influence of the thickness is considered to be very small. In case of the material thickness of 0.6mm, the rate of change increases due to the deep drawing depth relative to the material thickness. The sizes of the punches R and die R have the greatest influence on the change in thickness of the material in drawing molding, the smaller the punch R, the thinner the edges of the product, The larger the R of the die, the greater the material thickness of the flange portion. As the coefficient of friction and the blank holder pressure increase, the frictional force of the flange portion increases, which increases the radial force in the drawing process and increases the thickness change of the flange portion.

• Design & Manufacturing
• /
• 제2권2호
• /
• pp.43-47
• /
• 2008

This paper is concerned with the analysis of material flow characteristics of stepped rod forming. The analysis in this paper concentrated on the evaluation of the design parameters for deformation patterns of tube forming, load characteristics, extruded length, and die pressure. The design factors such as punch nose radius, die corner radius, friction factor, and punch face angle are involved in the simulation. The stepped rod forming is analyzed by using a commercial finite element code. This simulation makes use of stepped rod material and punch geometry on the basis of punch geometry recommended by International Cold Forging Group. As radius ratio is large, forming load was reduced but extruded length ratio was increased.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2005년도 ISMP
• /
• pp.67-88
• /
• 2005

Mold-Flow 3 Die Stack CSP of Mold array packaging with different Gate types. As high density package option such as 3 or 4 die stacking technologies are developed, the major concerning points of mold related qualities such as incomplete mold, exposed wires and wire sweeping issues are increased because of its narrow space between die top and mold surface and higher wiring density. Full 3D rheokinetic simulation of Mold flow for 3 die stacking structure case was done with the rheological parameters acquired from Slit-Die rheometer and DSC of commercial EMC. The center gate showed severe void but corner gate showed relatively better void performance. But in case of wire sweeping related, the center gate type showed less wire sweeping than corner gate types. From the simulation results, corner gate types showed increased velocity, shear stress and mold pressure near the gate and final filling zone. The experimental Case study and the Mold flow simulation showed good agreement on the mold void and wire sweeping related prediction. Full 3D simulation methodologies with proper rheokinetic material characterization by thermal and rheological instruments enable the prediction of micro-scale mold filling behavior in the multi die stacking and other complicated packaging structures for the future application.

• 한국항공운항학회지
• /
• 제13권1호
• /
• pp.43-49
• /
• 2005

There are several ways to mold the complex material, and it is divided to vacuum pack mold, compression mold, and hand lay up for a high molecular substance as a basic material. Moreover, it can be divided to general manufacturing (Single form) and mold manufacturing(Mold form) under normal temperature for Firefly. Firefly was manufactured with hand lay up and general manufacturing that using the foam core, glass fabric, and template without mold. However, mold manufacturing that is producing the surface by semi-sandwich using thin foam core and glass fabric then reinforce the inside with spar and rib is on developing. Mold manufacturing can make easy to production, standardize the quality, and possible to mass producing. In this paper, we present the mold producing process for canard aircraft "Firefly", and the problems and solutions during producing Firefly. Moreover, it complements the defect that the problems caused by master manufacturing error when produce several masters of a large part, and make the manufacturing process to be shortened by the replacement from the supplementary plate to the foam that is installed when producing lay up mold.

• Design & Manufacturing
• /
• 제13권2호
• /
• pp.44-48
• /
• 2019

Motor core products are used as materials for electrical steel sheets and cold-rolled steel sheets according to the performance of motors. The cemented carbide material of the mold punch applied to the motor core material causes many troubles due to abrasion and burr problem. The selection of these materials has a great effect on the production life, mass production, product quality as well as mold life. The cemented carbide applied to the products of the motor core is recognized as a very important part. In this study, cold rolled steel sheet was applied to motor core SCP-1 steel 1.0mm, and The effects of abrasion and punching oil on the shear process were investigated for the selection of cemented carbide. Experiments were conducted to select and apply cemented carbide only for the motor core punch optimized for cold rolled steel. The results showed that the cemented carbide material of $CDK3^{***}$ produced the least wear and burrs.