• 한국주조공학회지
• /
• 제11권6호
• /
• pp.475-481
• /
• 1991

In this study the fabrication technology and mechanical properties of AC8A/$Al_2O_3$ Composites by squeeze casting process were investigated to develope for application as the piston materials that require good friction, wear resistance, and thermal stability. AC8A/$Al_2O_3$ composistes without a porosity and the break of preform were fabricated at the melt temperature of $740^{\circ}C$, the preform temperature of $500^{\circ}C$, and mold temperature of $400^{\circ}C$ under the applied pressure of $1200kg/cm^2$ as the results of the observation of microstructures. As the results of this study, the tensile strength of AC8A/$Al_2O_3$ composites was not increased linearly with $Al_2O_3$ volume fraction and so it seemed not to agree with the rule of mixture, which had been used often in metal matrix composite. Also the tensile strength after thermal fatigue test was little different from that before the test. Consequently it was thought that AC8A/$Al_2O_3$ composites fabricated under our experimental conditions had a good thermal stability and subsequently a good interface bonding. Wear rate(i.e., volume loss per unit sliding distance) of AC8A/$Al_2O_3$ composites was decreased with $Al_2O_3$ volume fraction and the sliding speed at both room temperature and $250^{\circ}C$ and so there was a good correlation between wear rate and hardness. Also the wear rate of AC/8A20% $Al_2O_3$ composities was obtained the value of $1.65cm^3/cm$ at sliding speed of 1.14m/sec as compared with about $3.0\;{\times}10^{-8}cm^3/cm$ hyereutectie Al-Si alloy(Al-16%Si-2%Cu-1%Fe-1%Ni), which applied presently for piston materials. The wear behavior of $Al_2O_3$ composites was observed to a type of abrasive wear by the SEM view of wear surface.

• 대한치과보철학회지
• /
• 제43권1호
• /
• pp.52-60
• /
• 2005

Purpose. The intent of this study was to evaluate the effects of curing conditions on self-curing denture base resins to find out proper condition in self-curing resin polymerization. Materials and methods, In this study, 3 commercial self-curing denture base resins are used Vertex SC, Tokuso Rebase and Jet Denture Repair Acrylic. After mixing the self curing resin, it was placed in a stainless steel mold(3$\times$6$\times$60mm). The mold containing the resin was placed under the following conditions: in air at 23$^{\circ}C$; or in water at 23$^{\circ}C$; or in water at 23$^{\circ}C$ under pressure(20psi); or in water at 37$^{\circ}C$ under pressure(20psi) or in water at 50$^{\circ}C$ under pressure(20psi) , or in water at 65$^{\circ}C$ under pressure(20psi), respectively. Also heat-curing denture base resin is polymerized according to manufactures' instructions as control. Fracture toughness was measured by a single edge notched beam(SENB) method. Notch about 3mm deep was carved at the center of the long axis of the specimen using a dental diamond disk driven by a dental micro engine. The flexural test was carried out at a crosshead speed 0.5mm/min and fracture surface were observed under measuring microscope. Results and conclusion . The results obtained were summarized as follows : 1. The fracture toughness value of self-curing denture base resins were relatively lower than that of heat-curing denture base resin. 2. In Vertex SC and Jet Denture Repair Acrylic, higher fracture toughness value was observed in the curing environment with pressure but in Tokuso Rebase, low fracture toughness value was observed but there was no statistical difference. 3. Higher fracture toughness value was observed in the curing environment with water than air but there was no statistical difference. 4. Raising the temperature in water showed the increase of fracture toughness.

• Restorative Dentistry and Endodontics
• /
• 제12권1호
• /
• pp.39-49
• /
• 1986

The purpose of this study was to observe characteristic properties through the polarization curves and SEM images from 4 different types of amalgam obtained by using the potentiostats (Princeton EG & G) & SEM (Jeol/35), and to investigate the degree of corrosion on the oxidation peak of the each phase of amalgam. After each amalgam alloy and Hg was triturated as the direction of the manufacturer by means of the mechanical amalgamator (Shofu Co.), the triturated mass was inserted into the cylindrical metal mold which was 12mm in diameter and 10.0mm in height and was condensed by using routine manner. The specimen was removed from the mold and stored at room temperature for about 24 hours. The standard surface preparation was routinely carried out. Anodic polarization measurement was employed to confirm the corrosion behaviour of the amalgams in a 0.9% saline solution (P.H: 6.8-7.0) at $37^{\circ}C$. The initial rest potential (corrosion potential) was determined after 30 minutes of immersion of specimen in electrolyte, and the potential scan was begun at the point of 100mV cathodic from the corrosion potential. The scan rate was 0.17mV/sec. in the study to observe the degree of corrosion of each phase. SEI and EPMA images on the determined oxidation peaks of each amalgam were observed. The results were as follows: 1. In the four anodic polarization curves, low copper amalgams have three oxidation peaks and high copper amalgams have two oxidation peaks, -270mV, +26mV and +179mV(SEC) in the low copper lathe cut, and -300mV, +39mV and +163mV(SEC) in the low copper spherical. -4mV and +154mV(SEC) in the Dispersalloy, and +17mV and +180mV(SEC) in the Tytin as high copper amalgams. 2. ${\gamma}_2$ phase in the low copper amalgam and ${\eta}$ phase in the high copper amalgam were the most corrodible phases and Ag-Cu eutectic in high copper amalgam was the most slowly corroded phase. 3. Low copper amalgam was more susceptible in corrosion than high copper amalgam.

• 한국세라믹학회지
• /
• 제53권4호
• /
• pp.386-392
• /
• 2016

Heat insulation plates of fumed silica were prepared by mixing fumed silica, SiC powder and chopped glass fiber by a high speed mixer followed by pressing of the mixture powder in a stainless steel mold of $100{\times}100mm$. Composition of the plates, particle size of SiC, and type of inorganic binder were varied for observation of their contribution to heat insulation of the plate. The plate was installed on the upper portion of an electric furnace the inside temperature of which was maintained at $400^{\circ}C$ and $600^{\circ}C$, for investigation of heat transfer through the plate from inside of the electric furnace to outside atmosphere. Surface temperatures were measured in real time using a thermographic camera. The particle size of SiC was varied in the range of $1.3{\sim}17.5{\mu}m$ and the insulation was found to be most excellent when SiC of $2.2{\mu}m$ was incorporated. When the size of SiC was smaller or larger than $2.2{\mu}m$, the heat insulation effect was decreased. Inorganic binders of alkali silicate and phosphate were tested and the phosphate was found to maintain the heat insulation property while increasing mechanical properties.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.1109-1116
• /
• 2009

건축기술의 발달로 유리가 벽의 구조로 일반화도어 건축되고 있으며, 기존 벽의 역할인 수직 하중을 지탱하는 역할이 없어지게 되었다. 기능과 아름다운 면을 강조하게 되어 벽이 커튼의 역할만 하게 되어, 객차 실내 유리창에 접근시 차가운 느낌으로 불쾌감을 유발 한다. 그리고 유리창 아래에 바닥 난방을 했음에도 유리창에 외풍 발생으로 결로 현상이 발생하며, 즉 유리창 주변에 물방울이 발생(곰팡이 발생 원인)하여 겨울철 난방 에너지와 여름철 외부 온열이 유리를 통해 이동 하게 된다. 그러므로 에너지효율 감소에 절대적으로 영향을 준다. 객차에 발열 유리시스템을 적용하면 유리창 표면에는 냉기의 확산이 방생 하지 않으며, 객차의 실내 냉 난방시 에너지 절감 효과가 있다.

• Applied Microscopy
• /
• 제42권1호
• /
• pp.43-48
• /
• 2012

본 연구는 ceresin 왁스와 candellila 왁스 및 microcrystalline왁스를 혼합하고 액체파라핀 오일을 첨가하여 성형한 립스틱(LS-1, LS-2)과 capric/caprylic triglyceride 오일을 첨가하여 성형한 립스틱(LS-3, LS-4)을 각각 제조하여 성형 후 $5^{\circ}C$ 냉장실에 보관한 립스틱(LS-1, LS-3)과 성형 후 냉장실($5^{\circ}C$)에 18시간 방치한 후 항온기($45^{\circ}C$)에 5시간 보관한 다음 냉장실($5^{\circ}C$)에서 계속 보관한 립스틱(LS-2, LS-4) 왁스의 3차원적 구조를 주사전자현미경으로 관찰하였다. $5^{\circ}C$ 냉장실에서 보관된 LS-1과 LS-3 립스틱 왁스 구조는 오일의 종류와 관계없이 $45^{\circ}C$ 항온기에 5시간 방치한 다음 냉장실($5^{\circ}C$)에 보관한 LS-2과 LS-4 립스틱의 구조보다 깨끗한 모양을 하고 있었다. 또한, 왁스구조의 크기도 사용한 왁스의 종류와 관계없이 성형 후 보관온도가 증가함에 따라 왁스의 3차원적 구조가 변형되는 것으로 확인되었다. 본 연구결과 립스틱의 성형 후 보관온도가 증가하면 왁스구조의 크기가 증가하고 모양도 불규칙하게 변형되어 오일의 발한현상을 일으킬 수 있다.

• Corrosion Science and Technology
• /
• 제13권1호
• /
• pp.28-35
• /
• 2014

Recently, the fuel oil of diesel engines of marine ships has been increasingly changed to heavy oil of low quality as the oil price is getting higher and higher. Therefore, the spiral gear attached at the motor of the oil purifier which plays an important role to purify the heavy oil is also easy to expose at severe environmental condition due to the purification of the heavy oil in higher temperature. Thus, the material of the spiral gear requires a better mechanical strength, wear and corrosion resistance. In this study, the heat treatment(tempering) with various holding time at temperature of $500^{\circ}C$ was carried out to the alloy of Cu-7Al-2.5Si as centrifugal casting, and the properties of both hardness and corrosion resistance with and without heat treatment were investigated with observation of the microstructure and with electrochemical methods, such as measurement of corrosion potential, cathodic and anodic polarization curves, cyclic voltammogram, and a.c. impedance. in natural seawater solution. The ${\alpha}$, ${\beta}^{\prime}$ and ${\gamma}_2$ phases were observed in the material in spite of no heat treatment due to quenching effect of a spin mold. However, their phases, that is, ${\beta}^{\prime}$ and ${\gamma}_2$ phases decreased gradually with increasing the holding time at a constant temperature of $500^{\circ}C$. The hardness more or less decreased with heat treatment, however its corrosion resistance was improved with the heat treatment. Furthermore, the longer holding time, the better corrosion resistance. In addition, when the holding time was 48hrs, its corrosion current density showed the lowest value. The pattern of corroded surface was nearly similar to that of the pitting corrosion, and this morphology was greatly observed in the case of no heat treatment. It is considered that ${\gamma}_2$ phase at the grain boundary was corroded preferentially as an anode. However, the pattern of general corrosion exhibited increasingly due to decreasing the ${\gamma}_2$ phase with heat treatment. Consequently, it is suggested that the corrosion resistance of Cu-7Al-2.5Si alloy can be improved with the heat treatment as a holding time for 48 hrs at $500^{\circ}C$.

• 대한소아치과학회지
• /
• 제29권4호
• /
• pp.632-640
• /
• 2002

초음파 진동을 치의학에 처음 이용한 것은 치석 제거기였으나, 최근에는 주조금속과 레진 인레이를 접착할 때, 인산아연시멘트나 레진시멘트의 점도를 낮추는데 이용되고 있다. 이러한 초음파 진동은 재료의 흐름성을 증가시킴으로써 피막도를 낮추고, 따라서 수복물 주위의 미제누출을 감소시킬 수 있는 장점이 있다. 그러나, 복합레진의 수복에 있어서 이러한 초음파 진동의 임상적 효과에 관한 연구가 아직까지 미흡한 실정이다. 이에 저자는 초음파 진동을 상아질 결합제에 적용하여 점도를 감소시킴으로써 상아세관으로의 레진 침투 정도의 변화와 결합력에 미치는 효과를 알아보고자 하였다. 발거 후 실온의 0.1% thymol 용액에 보관된 88개의 건전한 사람의 대구치를 치관부 법랑질을 제거하고 아크릴 레진을 이용하여 직경 1-inch의 PVC 관에 매몰하였다. 각 시편의 교합면이 아크릴봉과 동일한 높이가 되도록 220-, 500-grit의 연마지로 순차적으로 연마하였고, 무작위로 추출하여 각 군당 22개씩 네 군으로 분류하였다. 1군과 2군은 Single Bond(3M-ESPE, St. Paul, USA)를 3군과 4군은 One-Step(Bisco Inc., Schaumburg, USA)을 제조사의 지시에 따라 치면을 산부식, 수세, 건조한 후 연속하여 2번을 도포하였다. 2군과 4군은 초음파 치석제거기를 이용하여 치면에 대고 10 초간 진동을 가한 후 광중합하였다. 이후 직경 2.3mm, 높이 3.5mm의 Teflon mold(Ultradent Products Inc., South Jordan, USA)를 이용하여 복합레진을 충전한 후 40초씩 두 번에 나누어 광중합하였다. 모든 시편은 24시간 동안 실온의 수도물에 보관한 후 열순환을 시행하고, 만능측정기(Instron 4465, Canton, USA)로 전단결합강도를 측정하였으며 resin tag의 양상을 비교하기 위해 각 군의 시편의 치질을 탈회시킨 후에 표면을 주사전자 현미경으로 관찰하여 다음과 같은 결과를 얻었다. 1. 초음파 진동을 가하지 않은 1군, 3군에 비해 초음파 진동을 가한 2군과 4군에서 전단결합강도가 유의하게 높게 나타났다(p<0.05). 2. Single Bond와 One-Step의 전단결합강도는 유의한 차이를 보이지 않았다(p>0.05). 3. 전자현미경 관찰에서 초음파 진동을 가한 군에서 resin tag의 길이가 길었고, lateral branch의 수도 많이 관찰되었다.

• 한국식품저장유통학회지
• /
• 제9권3호
• /
• pp.315-320
• /
• 2002

전통메주의 과다건조로 인한 품질저하 및 유해 곰팡이 오염으로 인한 위생적 문제를 개선하기 위하여 백국균(Roligosporus)을 종국 제조에 이용하여 "캡슐형 메주"를 착안하고 그 품질특성을 조사하였다. R oligosporus을 0.5, 1, 2% (w/w) 비율로 첨가하여 캡슐형 메주와 종국을 넣지 않고 성형한 대조구 I,II형을 10~15$^{\circ}C$에서 3일간의 자연 건조하였다. 27일간 실외에서 발효한 대조구 I형이라 하고, 대조구 II형과 캡슐 타입 메주는 $25^{\circ}C$에서 7일간의 1차 발효(습도 80%)와 20일간의 실외 2차 발효(2.7$^{\circ}C$, 12월)를 실시하여 제조하여 이들의 품질특성을 상호, 비교하였다. 수분함량은 대조구 메주보다 캡슐형 메주에서 2.88~7.55%까지 높은 함량 차이를 보였다. pH값과 적정산도는 유의적인 차이가 없었다. 아미노태 질소는 대조구 I형(347.2 mg%)보다 캡슐형 메주군(800.80, 816.0, 901.60 mg%)은 대조구 I형보다 2.2~2.6배의 높은 발효율을 보였다. 환원당 함량은 캡슐형 메주군이 2.78~3.13%로 대조구 I형은 2.10%, 대조구 II형은 2.31%에 유사한 값을 나타냈다. 대조구 I형의 색차계 색도의 명도(L)값은 대조구 II형 및 캡슐형 메주보다 높았다. 메주보다 높았다.

• 생명과학회지
• /
• 제19권6호
• /
• pp.781-786
• /
• 2009

양파즙을 추출하여 수분과 설탕비를 맞추어 수분함량대비 0%, 3%, 6%, 9%, 12%, 15%를 첨가하여 식빵을 제조하였다. 식빵의 무게, 부피 및 비용적은 양파즙 첨가량이 증가할수록 증가하였고, 굽기손실율은 양파즙 첨가량이 증가할수록 낮아졌다. 색도를 측정한 결과 양파즙 첨가량이 증가할수록 백색도(L 값)는 낮게 나타났으며, 적색도 (a값)와 황색도 (b값)는 양파즙 첨가량이 많을수록 높게 나타났다. 양파즙 첨가 식빵의 pH 결과는 저장 기간 동안 감소하였으며, 무첨가군이 가장 높게 나타났고 양파즙 첨가 식빵이 낮게 나타났다. 경도를 측정한 결과 양파즙을 첨가할수록 낮았으며 무첨가군이 높게 나타났다. 저장기간이 경과함에 따라 경도는 증가하였으며 무첨가군이 양파즙 첨가군에 비해 급격하게 증가하였다. 저장기간이 경과함에 따라 수분활성도는 감소하였으나 양파즙 첨가식빵이 무첨가군에 비해 높았으며 호기성균과 곰팡이균의 변화 또한 저장기간이 증가할수록 균수는 증가하였다. 관능평가 결과 맛, 향, 표면상태, 식감, 종합적인 기호도에서 무첨가군과 유의적인 차이는 없었으나 3% 첨가군이 가장 높게 평가되었다. 관능결과로부터 양파즙 3${\sim}$5% 를 첨가하는 것이 최적의 범위로 판단되었고 양파즙을 첨가함으로 인해 건강, 기호성 식품일 뿐만 아니라 제품의 저장기간도 연장시켜주는 것으로 확인되었다.