• 한국전기전자재료학회논문지
• /
• 제21권10호
• /
• pp.954-960
• /
• 2008

The effects of elastic modulus coefficient and linear expansion coefficient of overhead distribution power line(ACSR $58 mm^2$) on sag behavior in distribution line have been investigated to clarify the difference between specification and experimental level. The elastic modulus coefficients of Al wire and steel wire were $5,182.6 kgf/mm^2,\;18,348.8 kgf/mm^2$, respectively Therefore, the computational composition elastic modulus coefficient of the power line was $7,063.5 kgf/mm^2$, while that of experimentally measured was $7681.1 kgf/mm^2$. As a result, we found that elastic modulus coefficient which was experimentally measured was higher than that of computational by 8.7 %. However, when planner designs the sag of disoibution line, the elastic modulus coefficient of power line $8,400 kgf/mm^2$ should be generally adopted. These two different using values lead to the sag difference of 0.62 m. The other results will be discussed.

• 한국지반환경공학회 논문집
• /
• 제8권4호
• /
• pp.47-55
• /
• 2007

본 연구는 연약지반의 압밀특성을 나타내는 정수중 하나인 압밀계수($C_v$)를 결정하는데 있어 피에조 콘 관입시험(PCPT)결과의 적용성을 평가하고자 양산-물금지역의 연약지반에서 실시된 피에조 콘 관입시험 자료와 같은 지역 44개소에서 시추한 심도별로 총 172개 자연시료를 사용하여 기본적인 실내토질시험(압밀시험, Atterberg 한계시험, 입도분포시험 등)을 실시하였다. 각 시료의 압밀시험결과를 사용하여 Terzaghi(1943) 압밀 이론으로 구한 구속탄성계수(M) 및 압밀계수($C_v$)를 각 시료에 상응하는 현장 흙에서 실시한 피에조 콘 관입시험(PCPT) 결과로 구한 구속탄성계수 및 압밀계수와 비교분석하였다. 압밀시험으로 구한 구속탄성계수는 피에조 콘 관입시험으로 구한 구속탄성계수와 높은 상관성을 보였고 Jones & Rust(1995)가 제안한 경험식으로 계산된 구속탄성계수가 본 연구에서 피에조 콘 관입시험으로 구한 구속탄성계수와 유사한 값을 보였다. 압밀시험으로 구한 압밀계수와 콘 관입시험 결과로 구한 압밀계수는 직선적 관계를 보였고 콘 관입시험 결과로 구한 압밀계수 값은 압밀시험으로 구한 압밀계수 값의 54%정도로 나타났다.

• Structural Engineering and Mechanics
• /
• 제72권6호
• /
• pp.737-746
• /
• 2019

Concrete mechanical properties change constantly with age, temperature, humidity and the other environmental factors. This research studies the effects of temperature and age on the development of concrete elastic modulus by a series of prism specimens. Elastic modulus test was conducted at various temperatures and ages in the laboratory to examine the effects of temperature and age on it. The experimental results reveal that the concrete elastic modulus decreases with the rise of temperature but increases with age. Then, a temperature coefficient K is proposed to describe the effects of temperature and validated by existing studies. Finally, on the basis of K, analytical models are proposed to determine the elastic modulus of concrete at a given temperature and age. The proposed models can offer designers an approach to obtain more accurate properties of concrete structures through the elastic modulus modification based on actual age and temperature, rather than using a value merely based on laboratory testing.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.302-305
• /
• 2005

In this study, settlement characteristics of 38 CFRD was investigated from monitoring data and the method to estimate the dam settlements considering valley shape during constructions was proposed. The construction modulus of dam was found to be dependent on void ratios and valley shape factor. The construction modulus varied with valley shape and decreased with increasing void ratio. Also, the modulus was increased when the shape coefficient was less than 4. The settlement investigation results showed that the total settlement was proportional to the value of the settlement coefficient multiplied by the shape coefficient divided by void ratio.

• 한국기계가공학회지
• /
• 제17권5호
• /
• pp.8-15
• /
• 2018

Films with special properties (e.g., water-repellent films, optical films, anti-reflection films, and flexible films) are referred to as functional films. Recently, there has been interest in fine patterning methods for film fabrication. In particular there have been many studies that use a UV nanoimprint process involving a UV curing method. In this paper, a polymer film was fabricated by the UV nanoimprint process with a micro-pattern, and its durability was evaluated by a wear test and a nano-indentation test. The film mechanical properties (such as coefficient of friction, hardness, and modulus of elasticity) were measured. Moreover, the choice of PUA type resin used in the UV nanoimprint process was confirmed to impact the durability of the thin film. Despite making the polymer film samples using the same method and PUA type resin, different coefficient of friction, hardness, and modulus of elasticity values were obtained. PUA 4 resin had the most favorable coefficient of friction, hardness, and modulus of elasticity. This material is predicted to produce a high durability functional film.

• 한국도로학회논문집
• /
• 제12권2호
• /
• pp.115-121
• /
• 2010

입도조정기층 재료의 역학적 특성평가를 위하여 15개 시료에 대해 반복재하 삼축압축시험, CBR 시험, 투수계수시험을 수행하였다. 입도조정기층 재료의 CBR 값은 32~110 범위(평균 81)에서 매우 폭넓게 결정되었으며, 수침조건에서 팽창량은 0.04mm 이하로 나타났다. 입도조정기층 재료의 탄성계수는 체적응력의 영향을 매우 크게 받았으며 선형체적응력모델의 적용성이 가장 뛰어남을 확인하였다. 입도조정기층 재료의 탄성계수는 100MPa~600MPa, 모델계수 $k_1$은 80~270, 모델계수 $k_2$는 0.1~0.6 사이에서 결정 되었다. 체가름시험과 다짐시험에서 결정된 지수물성치로부터 입도조정기층 재료의 탄성계수를 결정하는 경험모형을 제안하였다. 제안된 경험모형의 결정계수는 모델계수 $k_1$ 결정에 있어서는 0.423, 모델계수 $k_2$ 결정에 있어서는 0.920, 응력단계별 탄성계수 결정에 있어서는 0.872로 평가되었다.

• Geomechanics and Engineering
• /
• 제14권1호
• /
• pp.29-42
• /
• 2018

This paper presents the results of an empirical study in which square rock-like blocks containing two parallel pre-existing rough non-persistent joints were subjected to uniaxial compression load. The main purpose of this study was to investigate uniaxial compressive strength and deformation modulus of jointed specimens. Response Surface Method (RSM) was utilized to design experiments and investigate the effect of four joint parameters, namely joint roughness coefficient (JRC), bridge length (L), bridge angle (${\gamma}$), and joint inclination (${\theta}$). The interaction of these parameters on the uniaxial compressive strength (UCS) and deformation modulus of the blocks was investigated as well. The results indicated that an increase in joint roughness coefficient, bridge length and bridge angle increased compressive strength and deformation modulus. Moreover, increasing joint inclination decreased the two mechanical properties. The concept of 'interlocking cracks' which are mixed mode (shear-tensile cracks) was introduced. This type of cracks can happen in higher level of JRC. Initiation and propagation of this type of cracks reduces mechanical properties of sample before reaching its peak strength. The results of the Response Surface Methodology showed that the mutual interaction of the joint parameters had a significant influence on the compressive strength and deformation modulus.

• 한국지열·수열에너지학회논문집
• /
• 제17권4호
• /
• pp.15-27
• /
• 2021

In this study, the effect of design factors in a pump station on the pressure variations which are the main cause of water hammering has been investigated by numerical simulations. As design factors, the flow rate, Young's modulus, diameter, thickness, roughness coefficient of pipeline are considered. The relationships between the pressure variations and the design factors are analyzed. The results show that the pressure variation increases sensitively with the flow rate and Young's modulus, and increases gradually with the thickness and roughness coefficient of pipe, whereas it decreases with the pipe diameter. The wavelength of the pressure wave becomes longer for a smaller Young's modulus, a smaller pipe thickness and a bigger pipe diameter. These relationships are nondimensionalized, and logarithmic curve-fitted functions are proposed by regression analysis. Most effective factors on the nondimensional pressure variation is Young's modulus. Flow rate, roughness coefficient, relative thickness and pipe diameters are the next impact factors.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.59-62
• /
• 2000

In this study, the distribution of the effective modulus was investigated statistically Plain weave structures were modeled with random stacking phase shift angles and the effective modulus was calculated by the unit cell analysis. The analysis results indicated that the effect of random phase shift angles was significant on the modulus distribution. As the number of layers increased, the coefficient of variation decreased and higher degree of homogeneity was attained.

• 지질공학
• /
• 제29권3호
• /
• pp.339-349
• /
• 2019

국내 40개 구조물 설계 시 수행된 1,646개의 실내 및 현장시험 결과를 활용하여 국내 암종에 따른 동탄성계수의 분포특성을 파악하기 위하여 암종별 P파 속도, 정탄성계수, 동탄성계수 간의 상관식을 도출하고 기존 연구사례와 비교하여 검증하였다. P파 속도와 정탄성계수의 관계를 살펴보면 편마암에서는 선형, 화강암과 사암에서는 지수 함수의 관계를 보인다. 결정계수($R^2$)는 0.491~0.642로 높지 않지만, 결정계수를 0.836~0.990로 제시하고 있는 기존의 연구사례와 유사한 분포범위를 보인다. 정탄성계수와 동탄성계수의 상관식은 모든 암종에서 선형적인 관계를 보이며, 결정계수는 0.543~0.676이다. P파 속도와 동탄성계수의 상관식은 지수함수의 관계를 보이며, 결정계수는 0.875~0.940으로 높게 나타난다.