• 한국입자에어로졸학회지
• /
• 제9권4호
• /
• pp.209-219
• /
• 2013

We have used the modified diffusion flame burner to synthesize silica coated iron oxide nanoparticles having enhanced superparamagnetic property. Silica-encapsulated iron oxide particles were directly observed using a high resolution transmission electron microscope. From the energy dispersive X-ray spectroscopy (EDS) and zeta potential measurements, the iron oxide particles were found to be completely covered by a silica coating layer. X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) measurements revealed that the iron oxide core consists of ${\gamma}-Fe_2O_3$ rather than ${\alpha}-Fe_2O_3$. Our magnetization measurements support this conclusion. Biocompatibility test of the silica-coated iron oxide nanoparticles is also conducted using the protein adsorption onto the coated particle.

• Bulletin of the Korean Chemical Society
• /
• 제33권7호
• /
• pp.2224-2228
• /
• 2012

This study describes the ability of capillary electrochromatography (CEC) for the determination of imidacloprid and carbendazim in tomato samples. A novel liquid crystal crown ether modified hybrid silica monolithic column was synthesized, characterized and developed as separation column for the first time. Baseline separation of imidacloprid and carbendazim could be achieved using a mobile phase containing 90% (v/v) 20 mmol/L phosphate buffer (pH 7.0) and 10% (v/v) acetonitrile. The matrix matched calibration curves were linear with correlation coefficient $r^2$ > 0.9998 in the range of 0.20-10.00 mg/L. The limits of detection for imidacloprid and carbendazim were 0.061 and 0.15 mg/kg, respectively, which were below the maximum residue limits established by the European Union as well as Codex Alimentarius. Average recoveries for imidacloprid and carbendazim varied from 101.6-108.0% with relative standard deviations lower than 6.3%. This method was applied to the analysis of tomatoes collected from local markets.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 추계 학술논문 발표대회
• /
• pp.68-71
• /
• 2013

Reactive Powder Concrete (RPC) is an ultra high strength and high ductility cement-based composite material and has shown some promise as a new generation concrete in construction field. It is characterized by a silica fume-cement mixture with very low water-binder (w/b) ratio and very dense microstructure, which is formed using various powders such as cement, silica fume and very fine quartz sand (0.15~0.4mm) instead of ordinary coarse aggregate. However, the unit weight of cement in RPC is as high as 900~1,000 kg/㎥ due to the use of very fine sand instead of coarse aggregate, and a large volume of relatively expensive silica fume as a high reactivity pozzolan is also used, which is not produced in Korea and thus must be imported. Since the density of RPC has a heavy weight at 2.5~3.0 g/㎤. In this study, the modified RPC was made by the combination of ternary pozzolanic materials such as blast furnace slag and fly ash, silica fume in order to economically and practically feasible for Korea's situation. The fire resistance and structural behavior of the modified RPC exposed to high temperature were investigated.

• 한국산학기술학회논문지
• /
• 제20권5호
• /
• pp.1-6
• /
• 2019

유기 염료가 도핑 된 실리카 나노입자는 바이오 라벨링, 바이오 이미징 및 바이오 센싱에 사용되고 있는 유망한 나노소재이다. 일반적으로 형광 실리카 나노입자는 수정된 스토버 방법($St{\ddot{o}}ber$ Method)으로 합성된다. 본 연구에서는 다양한 크기를 갖는 염료가 첨가되지 않은 형광 실리카 나노입자를 수정된 스토버 합성법인 졸겔 공정으로 합성하였다. 졸겔 공정 중에 기능성 물질인 APTES를 첨가제로 첨가하였다. 졸겔 공정으로 합성된 실리카 나노입자는 $400^{\circ}C$에서 2시간 동안 하소되었다. 합성된 실리카 나노입자의 표면형상과 크기를 전계방출 주사전자현미경으로 조사하였고, 합성된 실리카 나노입자의 형광 특성은 파장 365 nm의 자외선 램프를 조사하여 확인하였다. 또한 합성된 실리카 나노입자의 광발광 (PL) 특성을 형광 분석 형광법으로 조사하였다. 그 결과 합성된 실리카 나노입자는 입자의 크기와 무관하게 모두 청색 형광 특성을 갖는 것으로 확인되었다. 특히, 실리카 나노입자의 크기가 증가할수록 PL 강도는 감소하였다. 염료가 첨가되지 않은 실리카 나노입자의 청색 형광 특성은 APTES 층의 $NH_2$ 기능기와 실리카 매트릭스 뼈대 내부의 산소관련 결함과의 결합에 기인하는 것으로 추정된다.

• KCI Concrete Journal
• /
• 제14권2호
• /
• pp.76-80
• /
• 2002

The role of high volume Class F fly ash in reducing expansion due to Alkali-Silica Reaction (ASR) was investigated. A series of modified ASTM C 1260 tests were performed under three different levels of NaOH normality, extending the test period to 28 days, using high- or low alkali cement, and Class F fly ash up to 58 ％ by mass of cement. A reactive siliceous fine aggregate was used. The test results confirm that HVFA replacement in a cementitious system significantly helps in controlling expansion caused by ASR.

• Structural Engineering and Mechanics
• /
• 제54권6호
• /
• pp.1201-1216
• /
• 2015

This paper presents the details of size independent fracture energy and bi-linear tension softening relation for nano modified high strength concrete. Nano silica in powder form has been used as partial replacement of cement by 2 wt%. Two popular methods, namely, simplified boundary effect method of Karihaloo et al. (2003) and RILEM (1985) fracture energy with P-${\delta}$ tail correction have been employed for estimation of size independent fracture energy for nano modified high strength concrete (compressive strength ranges from 55 MPa to 72 MPa). It is found that both the methods gave nearly same values, which is an additional evidence that either of them can be employed for determination of size independent fracture energy. Bi-linear tension softening relation corresponding to their size independent fracture energy has been constructed in an inverse manner based on the concept of non-linear hinge from the load-crack mouth opening plots of notched three-point bend beams.

• Bulletin of the Korean Chemical Society
• /
• 제34권12호
• /
• pp.3805-3810
• /
• 2013

The surface modification of silica particles (SPs) was systemically conducted by the treatment of 0.1-10 wt % phenylsilanetriol (PST) on the basis of SPs used through two step processes: 1) the PST coating of SPs via evaporation under reduced pressure and 2) their thermal condensation leading to Si-O-Si bond formation via heating at $130^{\circ}C$. The evaluation of the modified SPs was conducted by the simple floating test on water and the measurement of the contact angle (CA) of water droplet on the 2-dimensional layer of modified SPs on slide glass. When PST was used about 2 wt % or above on the basis of SPs (about average size: 50 nm) used, the modified SPs were fully floated on the water and all dispersed into upper organic solvent layer after a shaking with the mixture of the water and benzene, indicating that the modified SPs have hydrophobic properties. The modified SPs were characterized by $^{29}Si$ MAS NMR and physicochemical properties including SEM, TEM, BET, adsorption/desorption isotherms, etc. were measured and compared each other in details. This research demonstrates that the organosilanetriol is a good modifier applicable for the surface modification of inorganic oxide particles using a low amount of modifier on the basis of oxide particles used.

• 공업화학
• /
• 제8권5호
• /
• pp.830-836
• /
• 1997

본 실험에서는 물유리를 사용하여 산세척에 의하여 제조된 산화철 입자의 표면개질에 대하여 연구하였다. 사용한 물유리의 $SiO_2$와 $Na_2O$의 몰비($SiO_2/Na_2O$)는 1, 2, 3.5이였다. 첨가되는 실리카의 양과 pH에 따라 산화철 현탁액의 분산성을 입자의 표면하전과 침강속도에 의하여 평가하였다. 그리고, 중성 영역에서 산화철 입자의 분산안정성을 유지할 수 있는 표면개질제(실리카)의 양을 도출하였으며, 물유리에 의한 산화철 입자의 표면개질을 습식 볼밀링에 의하여 슬러리 상태에서 실시하였다. 그 결과, 표면처리한 산화철 현탁액의 분산 안정성은 실리카의 양과 pH에 상호 의존하였다. 미처리한 산화철은 등전점인 pH 8에서 분산안정성을 잃고 있었으나, 산화철에 대하여 약 0.8wt%의 실리카로 표면처리한 산화철은 pH 5 이상 중성영역에서 분산안정성을 나타내었으며, 음이온성 계면활성제를 0.2wt% 이상 첨가에 의한 분산안정성이 더욱 증가되었다.

• Transactions on Electrical and Electronic Materials
• /
• 제7권4호
• /
• pp.167-172
• /
• 2006

Submicron colloidal silica coated with ceria were prepared by mixing of silica and nano ceria particles and modified by hydrothermal reaction. The polishing efficiency of the ceria coated silica slurry was tested over oxide film on silicon wafer. By changing the polishing pressure in the range of $140{\sim}420g/cm^2$ with the ceria coated silica slurries in $100{\sim}300nm$, rates, WIWNU and friction force were measured. The removal rate was in the order of 200, 100, and 300 nm size silica coated with ceria. It was known that the smaller particle size gives the higher removal rate with higher contact area in Cu slurry. In the case of oxide film, the indentation volume as well as contact area gives effect on the removal rate depending on the size of abrasives. The indentation volume increase with the size of abrasive particles, which results to higher removal rate. The highest removal rate in 200 nm silica core coated with ceria is discussed as proper combination of indentation and contact area effect.

• 한국세라믹학회지
• /
• 제45권1호
• /
• pp.48-53
• /
• 2008

In order to reduce signal delay in ULSI, an intermetal material of low dielectric constant is required. Ordered mesoporous silica film is proper to intermetal dielectric due to its low dielectric constant and superior mechanical properties. The ordered mesoporous silica film prepared by TEOS (tetraethoxysilane) / MTES (methyltriethoxysilane) mixed silica precursor and Brij-76 surfactant was surface-modified by HMDS (hexamethyldisilazane) treatment to reduce its dielectric constant. HMDS can substitute $-Si(CH_3)_3$ groups for -OH groups on the surface of silica wall. In order to modify interior silica wall, HMDS was treated by two different processes except the conventional spin coating. One process is that film is dipped and stirred in HMDS/n-hexane solution, and the other process is that film is exposed to evaporated HMDS. Through the investigation with different HMDS treatment, it was concluded that surface modification in evaporated HMDS was more effective to modify interior silica wall of nano-sized pores.