• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.35.2-35.2
• /
• 2011

A wind turbine power performance test is very important to wind turbine manufacturers because a wind farm developer or planner must want to define power performance characteristics and reliability of new wind turbines. Based on the IEC 61400-12-1, A wind turbine test site has to be nicely installed at flat terrain for testing. We are developing the wind power system which is IEC wind class IIa model with rated power of 3MW. KEPCO's Gochang power testing center was considered as candidates to build the test site without site calibration. This paper aims to verify the validity of the test site by using implement site assessment result that was based on IEC 61400-12-1.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.10
• /
• pp.159-165
• /
• 2007

This paper presents a method for the derivation of model parameters of a co-generation system using data measured through on-site generator characteristic testing and validates its model parameters. Dynamic models such as generator, excitation system, and turbine/governor are mainly dealt in this paper. For the purpose of validation of derived model parameters, the measured results are compared with simulation results. The comparisons between measured results and simulation results show good match.

• International Commerce and Information Review
• /
• v.8 no.2
• /
• pp.59-78
• /
• 2006

Considering rapid development of Internet Portal Site Contents in Korea, it is an important issue to analyze consumers' satisfaction and e-loyalty. This research develops, and empirically test a model for explaining/predicting the satisfaction and e-loyalty with internet-based Electronic Trade Site. This paper describes a theoretical model for investigating the Satisfaction and e-Loyalty of the Electronic Trade Site. This study investigates the concept of the satisfaction, e-loyalty in Electronic Trade Site and its determinants, and tries to establish e-loyalty analyzing model. The model of the satisfaction, e-loyalty electronic trade site is tested here using data from 158 samples. Based on the research model, a comprehensive set of hypotheses is formulated and a methodology for testing them is outlined. some of the hypotheses are tested empirically to demonstrate the applicability of the theoretical model. In examining the relationships of the determinants factors, service quality satisfaction show in significantly by Reliability, Information Provided, Trustworthiness, Convenience, International of contents but that show in not significantly by Interaction. In addition, Electronic Trade site retention shows indirect effect between customer satisfaction and referral. Although our research can not show the determinants of e-loyalty in the electronic trade site the empirical result give both theoretical and managerial implication for managing the consumers' satisfaction and e-loyalty in electronic trade site.

• Journal of Mechanical Science and Technology
• /
• v.15 no.9
• /
• pp.1319-1327
• /
• 2001

The results of stand and field testing of a combustion chamber for a heavy-duty 150 MW gas turbine are discussed. The model represented one of 14 identical segments of a tubular multican combustor constructed 1:1 scale. The model experiments were executed at a lower pressure than that in a real gas turbine. Combustion efficiency, pressure loss factor, pattern factor, liner wall temperature, flame radiation, fluctuating pressure and NOx emission were measured at partial and full loads for both model and on-site testing. The comparison of these items in the stand and field test results led to has the development of a method of calculation and the improvement of gas turbine combustors.

• International Journal of Quality Innovation
• /
• v.1 no.1
• /
• pp.64-74
• /
• 2000

This paper investigates the issue of performance testing on web browsing environments. Among the typical non-functional characteristics, index of link validity will be deeply explored. A framework to certify link correctness in web site is proposed. All possible navigation paths are first formulated to represent a usage model with the Markov chain property, which is then used to generate test script file statistically. With collecting any existing failure information followed by tracing these testing browsed paths, certification analysis may be performed by applying Markov chain theory. The certification result will yield some significant information such as: test coverage, reliability measure, confidence interval, etc. The proposed mechanism may provide not only completed but also systemic methodologies to find any linking errors and other web technologies errors. Besides, an actual practice of the proposed approach to a web-based system will be demonstrated quantitatively through a certification tool.

• Wind and Structures
• /
• v.1 no.1
• /
• pp.67-75
• /
• 1998

Tiger Gate Bridge, a steel suspension bridge with a main span of 888 m and a stiffening box girder, is located at the Pearl River Estuary, Guangdong Province, one of the typhoon-prone area in China. Focusing on the developing of the full aeroelastic model of the bridge and simulation of the wind field of the bridge site in a large boundary wind tunnel at Tongji University, Shanghai, China, some main results about the wind resistant properties of the bridge including aerodynamic instability, buffeting responses both being in operation and erection stages by using of a full aeroelastic model wind tunnel testing are introduced. Some of analytical approaches to those aerodynamic behaviours are also presented, and compared with experimental data of the testing.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.4
• /
• pp.33-46
• /
• 2007

HWAW (Harmonic Wavelet Analysis of Wave) method, which is non-destructive method using body and surface waves, has the advantages of obtaining 2D subsurface imaging because it uses a short receiver spacing to obtain the $V_s$ profile of whole depth. Even though the reliability of HWAW method has already been verified by using the numerical simulation in the various layered models, it is very difficult to evaluate the reliability of HWAW in the field because the exact $V_s$ values of the experimental site are unknown. In this study, a model testing site where the material properties and layer information could be controlled was constructed to verify the reliability of HWAW method. The detailed geometry of the testing site was strictly measured by surveying, and 140 vertical and horizontal geophones were established at the boundary of each layer to evaluate the dynamic material properties. Using the interval travel times between the upper and lower geophones, the body wave velocities of each layer were 2 dimensionally obtained as reference data, and comparative study using HWAW method was performed. By comparing 2D Vs profile obtained by HWAW method to the reference data, the reliability of HWAW method was verified.

• Journal of KIBIM
• /
• v.10 no.3
• /
• pp.22-32
• /
• 2020

Apartment building site planning is one of time consuming and labor-intensive tasks in architectural design field, due to its complexity in zoning regulations, building codes, local restrictions, and site-specific conditions. In other words, the process can be seen as a very complicated mathematical function with layers of variables and parameters, which ironically can be automated using computational methods on parametric tools. In this paper, a practical method of automating site planning of an apartment complex has been proposed by utilizing parametric approaches in Rhino 3D and Grasshopper. Two primary parameters, building heights and positions, determine the efficacy of building layouts under all regulatory standards, thus testing out numerous combinations of the two will produce some successful layout alternatives. For this, equation solver has been used for iterating the parametric model to sort out meaningful results among others. It also has been proven that the proposed process significantly reduced the time in site planning down to less than an hour on most cases, and many successful alternatives could be obtained by using multiple computers. Post evaluation processes such as day light and view shed analysis helped sort out the best performing ones out of functioning alternatives.

• Journal of Information Technology Applications and Management
• /
• v.23 no.4
• /
• pp.101-116
• /
• 2016

In this paper, we suggested a model that reflects the role played by the consumer's regulatory focus (promotion focus and prevention focus) as determinant factors of trust in the Web site. Also, we considered the moderating effects of consumers' purchasing experience toward online shopping. We conducted a two-month survey of 230 individuals using online shopping sites for hypotheses testing. The study results are summarized as follows. Firstly, promotion focused consumers showed higher trust to a web site compared to prevention focused consumers. Secondly, the moderating effect of purchasing experience between regulatory focus and consumer trust to a web site is statistically significant. The effect of a prevention focused consumers on consumer trust to a web site is stronger when purchasing experience toward online shopping is high compared to low. Based on these findings, this study presents practical and academic implications of the research.

• Fire Science and Engineering
• /
• v.29 no.4
• /
• pp.26-32
• /
• 2015

Carbon dioxide principally extinguishes fires by smothering, but an acceptable amount of extinguishing agent is needed. To assure the performance of carbon dioxide systems in Korea, computer programs certified by NEMA are being applied in system design. But the design errors can occur because the geometry of a model test facility is not the same as that of the actual fire area. Since the discharge rate tends to vary considerably with the flow pattern in a pipe, an on-site discharge test is necessary to ensure the performance of the system, especially with low pressure carbon dioxide. Technical standards for carbon dioxide systems do not give detailed guidelines for discharge tests at present. Based on comparative analysis of standards and practical tests, this paper suggests a methodology for on-site discharge tests.