• Journal of Communications and Networks
• /
• v.11 no.3
• /
• pp.279-286
• /
• 2009

This paper proposes an adaptive mode switching algorithm between two strategies in multiple antenna cellular networks:A single-user mode and a multi-user mode for the broadcast channel. If full channel state information is available at the base station, it is known that a multi user transmission strategy would outperform all single-user transmission strategies. In the absence of full side information, it is unclear what the capacity achieving method is, and thus there are few criteria to decide which of the myriad possible methods performs best given a system configuration. We compare a single user transmission and a multi user transmission with linear receivers in this paper where the transmitter and the receivers have multiple antennas, and find that neither strategy dom inates the other. There is instead a transition point between the two strategies. Then, the mode switching point is determined both ana lytically and numerically for a multiple antenna cellular downlink with correlation between transmit antennas.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.839-842
• /
• 2004

We present a fast-switching electro-optical device based on flexoelectro-optic effect in short pitch cholesterics oriented in uniform lying helix texture. The device has two operating modes: amplitude and phase modulation mode. The amplitude modulation mode is a fast in-plane switching of the device optic axis that enables to achieve a high percent of modulation of the transmitted light intensity whereas the phase mode gives a continuous change of the refractive index and thus of the phase shift of the transmitted light. By using a small concentration of diacrylate monomer and selecting the illumination conditions we have been able to create a inhomogeneous polymeric network mostly localized at both substrate surfaces and stabilize the two switching modes.

• 전기의세계
• /
• v.29 no.5
• /
• pp.321-328
• /
• 1980

The Q-switching oscillator of TE $M_{00}$ mode was constructed in order to improve the properties of energy focusing and amplification, and prevent laser materials from breakdown. The Q-switching was done by means of electro-optical effect using Glan prism and KDP Pockels cell. Sharp laser pulse of risetime-1 ns and variable pulse width 2-10 ns was obtained from Q-switching laser pulse by PTM method using a laser triggered spark gap (LTSG), Glan prism and Pockels cell. A single ultra-short pulse (picosec order in pulse width) was obtained from mode-locked pulse train in combination of a mode-locked oscillator using saturable dye cell with pulse shaping system using PTM method.d.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.171-171
• /
• 2010

Electro-optic characteristics of liquid crystal display using fringe field switching(FFS) device depend on many parameters such as cell retardation, electrode structure, rubbing angle, cell gap and dielectric anisotropy. In this paper, the light efficiency of FFS mode will be analyzed to confirm the electro-optic characteristics according to positive dielectric anisotropy such as transmittance, operating voltage and response time.

• Journal of Power Electronics
• /
• v.11 no.4
• /
• pp.520-526
• /
• 2011

This paper presents a balanced soft-chopping circuit and a modified PI controller for a high speed 4/2 Switched Reluctance Motor (SRM) with a 16 pulse per revolution encoder. The proposed balanced soft-chopping circuit can supply double the switching frequency in the fixed switching frequency of power devices to reduce current ripple. The modified PI controller uses maximum voltage, back-emf voltage and PI control modes to overcome the over-shoot current due to the time delay effect of current sensing. The maximum voltage mode can supply a fast excitation current with consideration of the hardware time delay. Then the back-emf voltage mode can suppress the current over-shoot with consideration of the feedback signal delay. Finally, the PI control mode can adjust the phase current to a desired value with a fast switching frequency due to the proposed balanced soft-chopping technology.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.10 no.3
• /
• pp.260-269
• /
• 2000

The fuzzy and state-feedback control systems have been applied in various areas from non-linear to linear systems. A Fuzzy controller is endowed with control rules and membership function that are constructed on the knowledge of expert, as like intuition and experience. but It is very difficult to obtain the exact values which are the membership function and consequent parameters. though apply back-propagation algorithm to the system, the convergence time a much. Besides, the state-feedback system is most widely used in industry due to its simple control structure and easily able to design the controller. but it is weak in complex system of higher degree and non-linear. In this paper presents the design of a fuzzy switching mode, it these two controllers work at different operation conditions, the advantages of both controller can be retained and the disadvantages can be removed. Between the Fuzzy and the State-feedback controlles, the good outputs are selected by the switching mode. Moreover it is powerful in complex system of higher degree and non-linear. In these sense compared with the state-feedback controller, the performance of the proposed controller was improvedin the section of linearization.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.4
• /
• pp.186-192
• /
• 2002

In this paper, interleaved boost power factor corrector(IBPFC) is applied as a pre-regulator in switch mode power supply. IBPFC can reduce input current ripple and effectively increase the switching frequency without increasing the switching losses, because input current is divided each 50% by two switching devices. IBPFC can be classified as three cases by duty ratio condition in continuous current mode and be carried out state space average modeling. According to the modeling, steady and transient state analysis is performed by steady elements and perturbation element. Control transfer function is derived for design of control system.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.38 no.1
• /
• pp.43-50
• /
• 1989

In this paper we present a new approach to control system design for multivariable systems using a sliding mode. In the applications of variable structure system (VSS) theory to multivariable systems, there exist some difficulties such as how to determine switching gains and how to reduce chattering phenomena in input and state trajectories. To cope with these drawbacks we introduce switching dynamics instead of switching logics to obtain the sliding mode. Consequently, we can obtain the new design approach which is much simpler than the VSS theory, And there do not exist chattering phenomena in this method because the obtained control inputs are continuous. Hierarchical control concepts are used to the control system design. Numerical examples are discussed as illustrations.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.3
• /
• pp.1-5
• /
• 2000

This paper presents a new sort of multilayer piezoelectric ceramic transformer for switching regulation power supplies. This piezoelectric transformer operate in the second thickness resonant vibration mode. Accordingly its resonant frequency is higher than 1 NHz, Because output power is low if input and output part of transformer are consisted of single layer, this research suggests a new method, which is consisted of both input and output part of transformer have 2-layered piezoelectric ceramics, The size of transformer is 20 mm in width and length, and 1.4 mm in thickness, respectively, To design a high efficient switching circuit of the transformer, internal circuit parameters were measured and then weve calculated a parameter of inductor nd capacitor to design a driving circuit, Weve used a MISFET and its driver circuit modified a calp oscillator circuit as the primary switching circuit.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.142-152
• /
• 2016

Common mode voltage (CMV) generation is a major problem in switching power converter fed induction motor drive systems. CMV is the zero sequence voltage generated due to the switching action of power converters. Even a small magnitude of CMV with a high rate of change may circulate large bearing currents which may damage a machine's bearings and shorten its life. There are several methods of controlling CMV. This paper presents 3-level sinusoidal pulse width modulation based techniques to control the magnitude and rate of change of CMV in multilevel AC-DC-AC drive systems. Simulation and experimental investigations have been presented to validate the performance of proposed technique to control CMV in 3-level neutral point clamped inverter based AC-DC-AC system.