• 한국안전학회지
• /
• 제9권1호
• /
• pp.28-30
• /
• 1994

Ultrasonic for MoSi$_2$/Y. C. Kim, C. K. Namkoong/MoSi$_2$in the silicides has excellence in the oxidation and corrosion resistence. When the solid state bonding sintered-MoSi$_2$/metal or the thermal sprayed coating by powder-MoSi$_2$on the metal are carried out, the defects may be occured at the bonded surface. So, the method for evaluating the existence of the defects by non-destructive inspection is strongly desired. Here, the characteristics of ultrasonic for sintered-MoSi$_2$are elucidated and the possibility of the detection of defects using by ultrasonic is investigated.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• 제3권1호
• /
• pp.35-39
• /
• 2000

The present study dealt with the relationships among the interfacial shear strength, the thickness of interfacial reaction layer and the impact value of $Nb/MoSi_2$ laminate composites. In addition, the tensile test was conducted to evaluate the fracture strain of $Nb/MoSi_2$ laminate composites. To change the thickness of the reaction layer, $Nb/MoSi_2$ laminate composites alternating sintered MoSi2 layers and Nb foils were fabricated as the parameter of hot press temperature. It has been found that the growth of the reaction layer increases the interfacial shear strength and decreases the impact value by localizing a plastic deformation of Nb foil. There also exist appropriate shear strength and the thickness of the reaction layer, which are capable of maximizing the fracture energy of $Nb/MoSi_2$.

• 한국분말재료학회지
• /
• 제4권4호
• /
• pp.298-303
• /
• 1997

The activated sintering behavior of $MoSi_2$ powder compacts with addition of 0.5 and 1.0 wt.%Ni during the sintering under As atmosphere was studied. The shrinkage was measured and the microstructures were observed by SEM (scanning electron microscopy) and BEI (backscattered electron image) along with the phase analysis by EDS during heating up to 155$0^{\circ}C$ and holding for various time at 155$0^{\circ}C$. The most of shrinkage occurred upon heating and 92% of theoretical density was attained after sintering for 1 hr at 155$0^{\circ}C$. However, little shrinkage ensued even for prolonged sintering over 1 hr at 155$0^{\circ}C$. A liquid film formed at about 135$0^{\circ}C$ along necks and grain boundaries. The polyhedral grain structure composed of $(Mo,Ni)_5Si_3$and $Ni_2Si$ across the $MoSi_2$ grain boundary developed at 155$0^{\circ}C$. It was concluded that the activated sintering of $MoSi_2$ powder by Ni led to the diffusion of Si into Ni decreasing the liquidus temperature and the enhanced diffusion of Mo and Si through such a liquid phase and/or interboundary of $(Mo,Ni)_5Si_3$.

• 한국세라믹학회지
• /
• 제31권4호
• /
• pp.399-406
• /
• 1994

The SiC/MoSi2 composite material was prepared by infiltration with the mixture of metal Si and MoSi2 into the preform of $\alpha$-SiC and graphite under the vacuum atmosphere of 10-1 torr. The mechanical properties, phases and microstructural characteristics have been investigated by employing an universal testing machine, scanning electron microscope and X-ray diffractometer. With the increase of MoSi2/Si mixing content, the quantity of the residual silicon phase was decreased and the hardness and fracture toughness of composite materials were increased. Also, as the infiltration temperature increased, a lot of fine-grained $\beta$-SiC phases, which were produced from the reaction of graphite and liquid silicon melt, were transformed to $\alpha$-SiC phases.

• 한국해양공학회지
• /
• 제23권6호
• /
• pp.93-98
• /
• 2009

The mechanical properties of $MoSi_2$ based composites containing various types of reinforcement, such as SiC, $ZrO_2$, and W, were investigated, based on detailed examinations of their microstructures. $MoSi_2$ based composites were fabricated at a temperature of $1350^{\circ}C$ using a hot-press device. The volume fraction of SiC and $ZrO_2$ particles in this composite system was fixed as 20%. The volume fraction of three types of W particles was changed from 10% to 30%. The characteristics of the $MoSi_2$ based composites were determined by means of optical microscopy and a three-point bending test. The addition of W particles to the $MoSi_2$ powders exhibited a sufficient improvement in the microstructure and mechanical property of the sintered $MoSi_2$ materials, compared to those of SiC and $ZrO_2$ particles. In particular, W/$MoSi_2$ composites containing W particles of 20 vol% represented a good flexural strength of about 530MPa at room temperature, accompanying a relative density of about 92%. The flexural strength of the W/$MoSi_2$ composites tended to decrease with an increase in the average size of the W particles.

• 한국자기학회지
• /
• 제9권5호
• /
• pp.256-262
• /
• 1999

DC/RF magnetron sputtering system을 이용하여 CoCr 박막 및 CoCrMo 박막의 Si 하지층의 도입에 따른 자기적 특성 및 미세구조의 변화에 대해 살펴보았다. 박막의 자기적 특성을 VSM을 통하여 측정한 결과, 고온에서 증착된 CoCrMo/Si 박막의 경우가 CoCr/Si 박막과는 달리 Si 하지층의 두께가 증가할수록 수직보자력값이 증가하는 것을 알 수 있었으며 AFM과 SEM을 이용한 surface morphology의 변화를 통하여 결정립 미세화와 균일화가 수직보자력을 증진시킴을 알 수 있었다. 또한, 박막의 결정배향성 및 미세구조를 XRD와 SEM을 통하여 관찰한 결과, CoCrMo/Si 박막의 (0002)우선 배향성이 CoCr/Si 박막의 (0002) 우선 배향성보다 상당히 크게 증진된 것을 볼 수 있었으며, SEM의 단면 측정을 통하여 CoCrMo/Si 박막과 CoCr/Si 박막의 기판 표면에서 성장하는 columnar 구조의 발달을 잘 관찰할 수 있었다.

• 한국자기학회지
• /
• 제10권6호
• /
• pp.269-273
• /
• 2000

Fe-l7Cr-2M(M=Si, Nb, Mo)합금분말을 Electrode Rotating Atomizer로 제조한 후 성형하여 소결한 시편의 첨가원소, 성형 압력 및 소결온도 에 따른 교류자기특성의 변화를 체계적으로 조사하였다 제조된 Fe-l7Cr-2M(M=Si, Nb, Mo) 합금분말의 형상은 구형이며, 포화자화값은 Mo와 Nb을 첨가한 Fe-l7Cr-2Mo과 Fe-l7Cr-Nb의 경우 약 155 emu/g로 Si을 첨가한 경우보다 크다. 성형압력 12 ton/$cm^2$, 소결온도 1200 $^{\circ}C$에서 제조된 Fe-l7Cr-2M(M=Si, Nb, Mo)합금분말 소결체의 진폭비 투자율은 주파수, f=1 kHz에서 3~5 Oe의 인가자장 범위에서 가장 크다. 전력손실은 인가자장 H$_{a}$ =5 Oe, 주파수 f=1 kHz에서 Fe-l7Cr-2Nb 경우 40 mW/cc로 Si이나 Mo를 첨가한 경우 보다 약 1/2값을 나타낸다.

• 한국표면공학회지
• /
• 제40권6호
• /
• pp.279-282
• /
• 2007

Cr-Mo-Si-C-N coatings were deposited on steel and Si wafer by a hybrid system of AIP and sputtering techniques using Cr, Mo and Si target in $Ar/N_2/CH_4$ gaseous mixture. Instrumental analyses of XRD and XPS revealed that the Cr-Mo-Si-C-N coatings must be a composite consisting of fine(Cr, Mo and Si)(C and N) crystallites and amorphous $Si_3N_4$ and SiC. The hardness value of Cr-Mo-Si-C-N coatings significantly increased from 41 GPa of Cr-Mo-C-N coatings to about 53 GPa with Si content of 9.3 at.% due to the refinement of (Cr, Mo and Si)(C and N) crystallites and the composite microstructure characteristics. A systematic investigation of the microstructures and mechanical properties of Cr-Mo-Si-C-N coatings prepared with various Si contents is reported in this paper.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.23-28
• /
• 2002

This paper describes the machining characteristics of the $MoSi_2$ based composites by electric discharge drilling with various tubular electrodes, besides, Hardness characteristics and microstructures of $Nb/MoSi_2$ laminate composites were evaluated from the variation of fabricating conditions such as preparation temperature, applied pressure and pressure holding time. $MoSi_2$ -based composites has been developed in new materials for jet engine of supersonic-speed airplanes and gas turbine for high- temperature generator. Achieving this objective may require new hard materials with high strength and high temperature-resistance. However, With the exception of grinding, traditional machining methods are not applicable to these new materials. Electric discharge machining (EDM) is a thermal process that utilizes a spark discharge to melt a conductive material, the tool electrode being almost non-unloaded, because there is no direct contact between the tool electrode and the workpiece. By combining a nonconducting ceramics with more conducting ceramic it was possible to raise the electrical conductivity. From experimental results, it was found that the lamination from Nb sheet and $MoSi_2$ powder was an excellent strategy to improve hardness characteristics of monolithic $MoSi_2$. However, interfacial reaction products like (Nb, Mo)$SiO_2$ and $Nb_2Si_3$ formed at the interface of $Nb/MoSi_2$ and increased with fabricating temperature. $MoSi_2$ composites which a hole drilling was not possible by the conventional machining process, enhanced the capacity of ED-drilling by adding $NbSi_2$ relative to that of SiC or $ZrO_2$ reinforcements.

• 마이크로전자및패키징학회지
• /
• 제8권2호
• /
• pp.15-18
• /
• 2001

Magnetron sputtering 장비를 이용하여 극자외선 노광 공정용 Mo/Si 다층 박막을 증착하였다. 증착 파워로는 Mo의 경우 DC파워를, Si의 경우 RF파워를 이용하였다. 각각의 target에 인가되는 DC 또는 RF 파워의 시간 및 파워 조절을 통해서 원하는 구조인자를 가진 다층박막을 증착하였다. 증착된 다층박막을 단면 TEM, low/high angle XRD 등을 이용하여 박막의 미세구조와 interfacial layer의 거동을 살펴 보았으며, low angle XRD로부터 다층박막을 간접적으로 평가할 수 있었으며, 단면 TEM으로부터 Si위에 형성되는 Mo의 interfacial layer가 Mo위에 형성되는 경우보다 두꺼운 것을 알 수 있었다.